Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Neousys Technology PCIe-PoE425bt
Summary of Contents for Neousys Technology PCIe-PoE425bt
- Page 1 Neousys Technology Inc. PCIe-PoE425bt User Manual Revision 1.0...
-
Page 2: Table Of Contents
ESD Precautions ........................7 About This Manual ......................... 8 Introduction PCIe-PoE425bt Specification ................... 10 Dimension ......................... 11 Setting Up Your PCIe-PoE425bt Card Unpacking Your PCIe-PoE425bt ................12 Status LEDs ......................13 DIP Switches ......................14 2.3.1 Switching Between at and bt Modes ..............14 2.3.2... -
Page 3: Legal Information
Legal Information Legal Information All Neousys Technology Inc. products shall be subject to the latest Standard Warranty Policy. Neousys Technology Inc. may modify, update or upgrade the software, firmware or any accompanying user documentation without prior notice. Neousys Technology Inc. will provide access to these new software, firmware or documentation releases from download sections of our website or through our service partners. -
Page 4: Contact Information
Tel: +886-4-2321-6650 Email, Website Americas Neousys Technology America, Inc. 3384 Commercial Avenue, Northbrook, IL 60062, USA (Illinois, USA) Tel: +1-847-656-3298 Email, Website China Shanghai Neousys Technology Co., Ltd. Room 429, Building 33, Guiping Road 680, Shanghai 200233, China Tel: +86-2161155366 Email, Website... -
Page 5: Notices
Disclaimer to change without prior notice. It does not represent commitment from Neousys Technology Inc. Neousys Technology Inc. shall not be liable for any direct, indirect, special, incidental, or consequential damages arising from the use of the product or documentation, nor for any infringement on third party rights. -
Page 6: Safety Precautions
Safety Precautions Safety Precautions Read these instructions carefully before you install, operate, or transport the system. Install the system or DIN rail associated with, at a sturdy location Install the power socket outlet near the system where it is easily accessible ... -
Page 7: Service And Maintenance
Service and Maintenance Service and Maintenance ONLY qualified personnel should service the system Shutdown the system, disconnect the power cord and all other connections before servicing the system When replacing/ installing additional components (expansion card, memory module, etc.), insert them as gently as possible while assuring proper connector engagement ESD Precautions ... -
Page 8: About This Manual
About This Manual About This Manual This manual introduces and describes how to setup/ install Neousys Technology PCIe-PoE425bt. As one of the first 2.5Gb industrial Power over Ethernet frame grabber cards on the market, it offers expandability, stability, flexibility and fast Ethernet access to peripheral devices. -
Page 9: Introduction
It is in compliance with IEEE 802.3bz standard to provide 2.5 Gbps bandwidth and is backward-compatible with 1000BASE-T, 100BASE-TX, and 10BASE-TE Ethernet. The PCIe-PoE425bt also features IEEE 802.3bt PSE capability. IEEE 802.3bt, or PoE++, the latest addition to Power over Ethernet specifications, allowing a single port to provide up to 90W of power supplied to a PD over a standard CAT-5e or CAT-6 Ethernet cable. -
Page 10: Pcie-Poe425Bt Specification
PCIe-PoE425bt PCIe-PoE425bt Specification Bus interface 4-lanes, Gen2 PCI Express interface 2.5G Ethernet ports by four Intel® I225-IT controllers, supporting 9.5 kB Gigabit Ethernet Port jumbo frame, teaming and IEEE 1588 In compliant with IEEE 802.3bt PoE++ Type 3 and Type 4 PSE,... -
Page 11: Dimension
PCIe-PoE425bt Dimension NOTE All measurements are in millimeters (mm). -
Page 12: Setting Up Your Pcie-Poe425Bt Card
Setting Up Your PCIe-PoE425bt Card Unpacking Your PCIe-PoE425bt Upon receiving the PCIe-PoE425bt package, please check immediately if the package contains all the items listed in the following table. If any item is missing or damaged, please contact your local dealer or Neousys Technology. -
Page 13: Status Leds
PCIe-PoE425bt Status LEDs Speed LED (1) LED Color Status Description Orange 2500 Mbps Orange 1000 Mbps Green or orange Green 100 Mbps 10 Mbps Active/Link LED (2) LED Color Status Description Ethernet port is disconnected Orange Ethernet port is connected and no data transmission... -
Page 14: Dip Switches
ID can be used as a parameter in API to specify the card. 2.3.1 Switching Between at and bt Modes The PCIe-PoE425bt card offers two power supply source methods. Users can choose between at mode (IEEE 802.3at) or high at mode (IEEE 802.3bt) by configuring DIP switch 4. Mode... -
Page 15: Board Id Settings
PCIe-PoE425bt 2.3.2 Board ID Settings The following illustrations describe DIP switch board ID settings. When installing multiple cards, please remember to set a different ID for each card. Board ID DIP Switch Position (P1 ~ P3) -
Page 16: Pcie-Poe425Bt Card Installation
PCIe-PoE425bt PCIe-PoE425bt Card Installation Once you have set up the DIP switch ID of your PCIe-PoE425bt for multi-card installation, then you are ready to install the PCIe-PoE425bt into the system. Please refer to the following installation procedures. Before disassembling the system enclosure and installing the card, please read the following instructions: ... -
Page 17: Hardware Installation
Power off and unplug the power cable from the system you wish to install to. Open the chassis (side panel) of the computer you wish to install the PCIe-PoE425bt into. Locate the x4 PCIe slot or a spare and compatible x16/ x8 PCIe slot. - Page 18 PCIe-PoE425bt Secure the PCIe-PoE425bt to the chassis with a screw. Connect the 6-pin PCIe power cable to the daughter board and the card, if need be. Reinstall the system’s chassis (panel) to complete the hardware installation process.
-
Page 19: Os Support And Driver Installation
Due to Intel’s policy, the system only provides driver support for Windows 10 64-bit. For Linux support, please use Linux kernel versions no later than 5.15. The following list contains the operating systems which have been tested in Neousys Technology Inc. Microsoft Windows 10 Professional 64-bit Microsoft Windows 10 IoT Enterprise 64-bit Ubuntu 22.04 LTS (5.15 kernel) -
Page 20: Network Settings
PCIe-PoE425bt Network Settings PCIe-PoE425bt offers Gigabit Ethernet connectivity via Intel I225-IT controller. When connecting to a high-speed PoE device, such as a GigE camera, you can configure driver settings for optimum transmission throughput and connection stability. Jumbo Frame Jumbo frames are Ethernet frames with more than 1500 bytes of payload. By increasing the payload size, large data packets can be transferred with less interruption, which reduces CPU utilization and increases overall data throughput. - Page 21 PCIe-PoE425bt Right click on the corresponding Local Area Connection (Marvell FastLinQ Edge 5Gbit Network …) and click on Properties.
- Page 22 PCIe-PoE425bt Click on the Configure button, the following dialog appears and click on the Advanced tab.
- Page 23 PCIe-PoE425bt Highlight Jumbo Packet and select a jumbo frame size from the Value drop-down list (9014 Byte is recommended for connecting devices with high data rate).
-
Page 24: Receive Buffers
PCIe-PoE425bt Receive Buffers Receive Buffers is another option which can affect data throughput. It determines the size of memory buffer allocated for receiving data. Increasing the size of Receive Buffers can improve the performance of receiving data. The default setting of Receive Buffers is 256 bytes. When connecting to an Ethernet device that generates large amount of data, you can set this option to a larger value (maximum 2048 bytes) for better performance. - Page 25 PCIe-PoE425bt Click on the Configure button, the following dialog appears and click on the Advanced tab.
- Page 26 PCIe-PoE425bt Scroll down the Property list and highlight Receive Buffers and enter a setting into the Value column (2048 Bytes is recommended for connecting devices with high data rate).
-
Page 27: Transmit Buffers
PCIe-PoE425bt Transmit Buffers Like Receive Buffers, Transmit Buffers can affect the transmission performance. The default setting of Transmit Buffers is 1024 bytes. If you encounter a performance issue while transmitting data, you can adjust the size of Transmit Buffers to a larger value (maximum 2048 bytes) for better performance. - Page 28 PCIe-PoE425bt Click Configure button, the following dialog appears and click on the Advanced tab.
- Page 29 PCIe-PoE425bt Scroll down and highlight Transmit Buffers and enter a setting into the Value column (2048 Bytes is recommended for connecting devices with high data rate).
-
Page 30: Appendix A Using Per-Port Poe On/Off Control
Appendix A Using Per-Port PoE On/Off Control PCIe-PoE425bt supports power on/off control for each of its PoE ports. With provided function APIs, users can turn on or turn off the power of each PoE port manually for fault-recovery or device power reset purpose. To use the function, you need to install the WDT_DIO_Setup.exe driver package. - Page 31 PCIe-PoE425bt 2. Click “Next >” and you may specify a directory you would like to install the files to or you can install to the default directory “C:\Neousys\WDT_DIO”.
- Page 32 PCIe-PoE425bt 3. Once the installation is finished, a dialog appears to prompt you to reboot the system. The WDT & DIO library will take effect after the system rebooted. 4. When you programming your program, the related files are located in...
-
Page 33: Per-Port On/Off Control Function Reference
PCIe-PoE425bt Per-Port On/Off Control Function Reference PCI_GetStatusPoEPort Syntax BYTE PCI_GetStatusPoEPort(DWORD boardId, DWORD port); Description Acquire current power on/off status of designated PoE port. boardId DWORD value (0 ~ 7) to indicate board ID set for your card. Please refer to DIP switch settings for your PCIe-PoE card. -
Page 34: Pci_Enablepoeport
PCIe-PoE425bt PCI_EnablePoEPort Syntax BOOL PCI_EnablePoEPort(DWORD boardId, DWORD port); Description Enable (turn on) PoE power for designated PoE port. boardId DWORD value (0 ~ 7) to indicate board ID set for your card. Parameter Please refer to DIP switch settings for your PCIe-PoE card. -
Page 35: Pci_Disablepoeport
PCIe-PoE425bt PCI_DisablePoEPort BOOL PCI_DisablePoEPort(DWORD boardId, DWORD port); Syntax Description Disable (turn off) PoE power for designated PoE port. boardId DWORD value (0 ~ 7) to indicate board ID set for your card. Parameter Please refer to DIP switch settings for your PCIe-PoE card.