Haiwell PLC User Manual page 7

en.haiwell.com
Step 6: CR26H Writes value 2 to end the calibration process
27H Low bytes of base weight of weights in channel 1, paragraph 1
28H High bytes of base weight of weights in channel 1, paragraph 1
29H Low bytes of base weight of weights in channel 1, paragraph 2
2AH High bytes of base weight of weights in channel 1, paragraph 2
2BH Low bytes of base weight of weights in channel 1, paragraph 3
2CH High bytes of base weight of weights in channel 1, paragraph 3
2DH Automatic peeling range of channel 1
2EH Channel 1 Weight Upper Limit Low Bytes (32 Bit Display)
2FH Channel 1 Weight Upper Limit High Bytes (32Bit Display)
30H~4FH Reserve
50H Channel 2 average weight
Channel 2 status code:
bit0：no-load（zero point weight）
bit1：exceed the weight upper limit
51H
bit2：stability of measurement value
bit3~15：reserved
52H Channel 2 Real-time weight
Channel 2 uses 32-bit display flags:
53H 0: 16-bit weight display
1: 32-bit weight display
Channel 2 Real-time Weight 32 Bit Value:
54H~55H 54H: 32-bit low byte
55H: 32-bit high byte
The average weight of channel 2 is 32 bits:
56H~57H 56H: 32-bit low byte
57H:32-bit high byte
58H Channel 2 Skin Weight Low Bytes
59H Channel 2 Skin Weight High Bytes
Channel 2 Control Setting
Bit 0: Reservation
5AH
Bit 1: Gross/Net Weight Display, 0-Gross Weight, 1-Net Weight
Bit2-15: Reservation
Channel 2 sampling frequency 0-7.5Hz，1-15Hz，2-30Hz，
5BH
3-60Hz，4-120Hz,5-240Hz，6-480Hz，7-960Hz
Reserved
5CH-5DH
5EH Channel 2 average number of times
5FH Channel 2 filter ratio
60H Channel 2 standstill checking times
Channel 2 standtill checking range
61H
Channel 2 zero tracking intensity
62H 0 :close zero tracking function
others: show zero tracking intensity(absolute value)
Channel 2 zero-point detection range
63H
Channel 2 weight upper limit
Set the upper limit value of weight, when measurement value is
64H
over the set value will record error code
Channel 2 Skin Weight Read (Settings)
When 16-bit display, read the current weight value (50H) as the
65H weight value of the leather weight and store it at 58H.
When 32-bit display, read CR56H and CR57H as skin weight Z
value and store them at 58H and 59H.
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
R
R
R
R/W32
R
R/W
R/W
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
7 / 24
Haiwell PLC -- Load Cell Module User Manual
2000
0
0
0
0
0
0
32767
32767
0
0
16 bits only use 58H, 32
bits use 58H 59H.
0
Switch the current
display weight to wool
Weight or net weight,
0 used in calculation the
value of 58H and 59H as
tare weight
3 range：0~7
10 range：1~100
2 range：0~5
5 range：0~500
range：0~10000
2
vaule,range ：
Abolute
0
0~200
vaule,range ：
Abolute
10
0~10000
32767
0: no operation
1: Read the weight value
0 as the tare weight and
store it at 58H 59H.
Others: Invalid