Controlling Other Components - Onkyo HT-R520 Instruction Manual

HT-R520_En.book Page 50 Monday, March 15, 2004 2:47 PM

Controlling Other Components

You can use the HT-R520's remote controller (RC-
570M) to control your other AV components, including
those made by other manufacturers. To do this you first
need to enter the appropriate remote control code for
your DVD player, TV, VCR, cable receiver, or satellite
receiver. Then you need to select the corresponding
remote controller mode (see page 10).
By entering the appropriate remote control code, the
[CD], [MD], and [CDR] mode buttons can also be used
with other manufacturer's components (e.g., DVD, TV,
VCR, satellite or cable receiver).
ON STANDBY
T V
I
V1 V2 V3
1 2 3
DVD MULTI CH
4 5 6
CD TAPE TUNER
7 8 9
+ 10
0
CLEAR
--/---
TONE
_
+
REMOTE MODE
DVD CD MD
TV VCR CABLE
DIMMER
TV
INPUT
+
CH
DISC
ENTER
-
PREV
Entering Remote Control Codes
Entering the appropriate remote control code for your
TV, VCR, and so on will allow you to control it with the
HT-R520's remote controller. You'll need to perform this
procedure for each component that you want to control.
1 Look up the remote control code for your
component.
See "Remote Control Codes" on page 51.
2
While holding down the [DVD], [TV],
[VCR], [CABLE], [SAT], [CD], [MD], or
[CDR] mode button, press the [STANDBY]
button.
Remote indicator flashes twice.
3 Within 30 seconds, use the number but-
tons to enter the 4-digit remote control
code.
50
Remote
indicator
I
TV
INPUT
STANDBY
+
TV CH
-
Number
buttons
T V VOL
TUNER/
TAPE
AMP
CDR
DVD, CD, MD,
CDR, TV, VCR,
SAT
CABLE, SAT
SLEEP
VOL
4
Select the remote controller mode, point
the remote controller at the component,
and check its operation.
Remote controller buttons that can be used in
DVD mode are shown on page 12. Those that can
be used with the TV, VCR, CABLE, and SAT
modes are shown on page 55.
If the remote controller works as expected, the code has
been entered correctly. If not, try again or try another
code.
Codes for Onkyo DVD Players
The remote control code for an Onkyo DVD player
depends on whether it's connected via
5001: Use this code if you've connected an
and an analog audio cable (RCA) to your DVD
player. This is the default setting, so if you're
using , you don't need to change anything.
Point the remote controller at the HT-R520 to
operate the DVD player.
5002: Use this code if your DVD player doesn't have
an socket, or you're not using
the remote controller at the DVD player to
operate it.
Resetting the [DVD], [CD], [MD] or [CDR]
Mode Button
By default, the [DVD], [CD], [MD] & [CDR] mode but-
tons are preprogrammed with remote control codes for
controlling Onkyo components connected via
you've entered another code for a button and now want
to return to its default, perform the following procedure.
1 While holding down the mode button that
you want to reset, press the TV [
ton.
Remote indicator flashes twice.
2
Press the mode button again.
The mode button is reset.
Resetting the Remote Controller
This section explains how to reset the remote controller
to its default settings.
1 While holding down the [AMP] mode but-
ton, press the
[STANDBY] button.
Remote indicator flashes 5 times.
2
Press the [AMP] mode button again.
The remote controller is reset.
, as follows:
cable
. Point
. If
] but-