Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Esse-ti 4G.evox
Summary of Contents for Esse-ti 4G.evox
- Page 1 User’s manual 29/04/2022...
- Page 2 All Esse-ti products are subjected to extensive reliability operational testing laboratories in order to provide total guarantee for the user. Esse-ti reserves the right to modify the product characteristics at any time without prior notice.
-
Page 3: Table Of Contents
Inserting the antenna ........................11 Connection to the telephone line ....................11 Connection to the LifTrack ......................12 Connection to the power supply ....................13 Turning 4G.evox on ........................13 4G.evox mounting operations ...................... 14 PROGRAMMING ........................ 15 Programming via telephone ....................15 SIM card expiration control ...................... -
Page 4: General Installation Instructions
• The product must be EXCLUSIVELY used for the purpose it was designed for. Esse-ti shall not be responsible for damages arising from improper use. • The product has been designed in compliance with the regulations in force and must be installed in systems that comply with the provisions of law. -
Page 5: Description
DESCRIPTION 4G.evox is a 4G telephone gateway designed to be used in conjunction with the LifTrack monitoring system. Connected to LifTrack via CAN-bus, 4G.evox forwards the information collected and processed by LifTrack sensors and inputs, via data, to an Esse-ti server. -
Page 6: Main Features
NiMH 800 mAh 7,2 V back up battery • 11-26 Vdc power supply input • Firmware update OTA Package contents • 4G.evox • Magnetic base antenna with cable (L= 2 m) • External adapter (input 100-240 Vac 50-60 Hz; output 12 Vdc 500 mA; CE mark) •... - Page 7 Functions • Local programming via telephone (DTMF tones) • Remote programming via SMS • Reading of programming codes via SMS • Data transmission through standard CAN-bus • Voice calls • Data connection and voice call simultaneously • Display of caller identification •...
-
Page 8: Hardware Description
Hardware description Antenna cable connector SIM CARD housing Terminal blocks for CAN-bus data transmission Micro USB A/B port for PC connection Main terminal blocks 100-240 Vac 12 Vdc external adapter input Backup battery connector LED indicating device operation status (red), LED indicating data transmission (yellow), LED indicating power supply status (blue), LED indicating signal strength (green), LED indicating line status (white) -
Page 9: Leds
MAIN TERMINAL BLOCKS Telephone line output for telephone set connection or autodialer/PABX analogue line connection +12/24 V 11-26 Vdc power supply terminal block Negative CAN-BUS TERMINAL BLOCKS CAN bus L CAN bus H LEDs Red LED: Device status indicator LED Yellow LED: Data transmission indicator LED Blue LED: Power supply status indicator LED Green LED: 4G LTE/UMTS/GSM signal indicator LED... -
Page 10: Installation
INSTALLATION Installation recommendations • 4G.evox must be installed in a location where the radio signal allows for using the 4G LTE/UMTS/GSM system. • It is advisable to leave plenty of space around 4G.evox for maintenance operations. • Do not install 4G.evox outdoors, since it lacks protection devices against weather conditions that can damage 4G.evox (water, humidity, etc.). -
Page 11: Inserting The Antenna
➢ Position the antenna with magnetic base so that any metal surfaces do not block the signal. Connection to the telephone line ➢ Connect 4G.evox to a standard telephone or to the PSTN input terminals of a PABX or autodialer using the TEL terminals (E in the picture at page Page 11... -
Page 12: Connection To The Liftrack
Connection to the LifTrack ➢ Connect 4G.evox to the LifTrack monitoring system following the diagram shown below: Page 12... -
Page 13: Connection To The Power Supply
Turning 4G.evox on ➢ Power 4G.evox. ➢ Wait 45 seconds after power-up to give time to 4G.evox to register correctly with the 4G LTE/UMTS/GSM network. ➢ Make sure the red LED (device status) flashes as shown in chapter “Signals”... -
Page 14: 4G.evox Mounting Operations
➢ Drill two holes with 5 mm diameter on the wall at a distance of 50 mm. ➢ Insert the 2 wall plugs and screws down until the screws are at a 5 mm distance from the wall. ➢ Place 4G.evox onto the two screws through the two back slots. Page 14... -
Page 15: Programming
PROGRAMMING It is possible to configure 4G.evox locally via a multi-frequency telephone or remotely via SMS. ROGRAMMING VIA TELEPHONE ➢ Connect 4G.evox to a multi-frequency telephone using TEL terminals (E in the picture at page 8). ➢ Lift the handset and dial the desired programming code (see table "Programming via telephone"). - Page 16 XXX: MCC of your telephone operator ROAMING Y…Y: MNC of your telephone operator **5*0*XXX*Y...Y# SETTING (in case 4G.evox registers with a different provider than the programmed, it is not possible to make or receive any calls) Default: roaming enabled Notification frequency...
- Page 17 1= notifications enabled EXTERNAL POWER Instructions to use e-stant web can be downloaded at the following link: ON E-STANT http://webshare.esse-ti.it/guide.zip X…X: telephone number appointed for SMS notifications of SIM card expiration, external power **40*X…X*X…X# NOTIFICATION failure/restore, 4G LTE/UMTS/GSM network restore,...
- Page 18 PROGRAMMING VIA TELEPHONE XX: minutes of external power failure, from 01 to 99 **81*XXYY# YY: minutes of external power restore, from 01 to 99 EXTERNAL POWER FAILURE **81*0# Disabling CONTROL Default: control disabled ENTERING NUMBERS TO CALL X…X: programming password **26*X…X*Y*Z…Z*Z…Z# Y: table position, from 1 to 6 Z…Z: telephone number...
-
Page 19: Sim Card Expiration Control
The built-in backup batteries ensure 8 operating hours in idle mode and 2 operating hours in conversation mode. If the battery check is enabled, every 15 days 4G.evox controls the integrity of the battery. If the battery is found dead or damaged, a notification SMS is sent with the following text message: “Dead battery”. -
Page 20: External Power Failure Control
- when dialing the telephone number 3339876543, 4G.evox will make a call to 0717506066 - etc. - when dialing any number not included in the “Dialed number” column, 4G.evox will send a call to the first telephone number included in the “Preset number” column. Page 20... - Page 21 ➢ Dial a telephone number by the connected telephone (autodialer or other telephone device) with 4G.evox. 4G.evox will check if the dialed number is already matched with a preset telephone number. If so, it will send a call to the preset number.
-
Page 22: Programming Via Sms
SMS. In case the administrator number has been previously set, programming via SMS is only allowed from such telephone number. An SMS notifying that programming has been completed will be sent back by 4G.evox to the same telephone number that forwarded the programming SMS. - Page 23 PROGRAMMING / READING CODE (C..C) Reading administrator number Setting programming password 19*X…X*Y…Y*Y…Y# Enabling SIM card expiration control 53*X…X# Disabling SIM card expiration control 53*0# Reading SIM card expiration control status Battery check enabling Battery check disabling Reading battery check status Low-battery check minimum value 52*X# Reading low-battery minimum value...
-
Page 24: Notification Message Format
Notification message format The format of the message notifying the user or the administrator who previously sent out a programming SMS, is the same as the programming message format. SMS notifying an accepted command ET?IL1*xxx#c..c SMS notifying a rejected command ET?IL1*xxx#c..cERR Example: outgoing SMS to enable battery check and to set the following incoming... -
Page 25: Services
UTGOING CALLS Allows you to dial over the mobile network. If 4G.evox is connected to a PABX, autodialer or other telephone device, please refer to the relevant instructions. If 4G.evox is connected to a telephone: ➢... -
Page 26: Measuring The Signal Level
This procedure allows you to check the 4G LTE/UMTS/GSM signal level through your telephone. ➢ Lift the handset and dial the code **30#. ➢ Wait for the signal reading. 4G.evox will send a number of short tones corresponding to the signal level: Tones Quality No signal... -
Page 27: Reading The Days Missing To Sim Card Expiration
EADING THE DAYS MISSING TO CARD EXPIRATION This procedure allows you to check how many days until the SIM card expiration. ➢ Lift the handset and dial **54#. ➢ After the confirmation tone hang up. After receiving the request, the gateway will send an SMS to the number programmed to be alerted. -
Page 28: Reading Advanced Device And Radio Cell Parameters
ET-IL1 programming string start *xxx# password string (default xxx = 0) 4G.evox will send one or two SMS to the number that sent the request with the following data: String Meaning (the values shown are for illustrative purposes) ET?IL1*XXX#904GEVOX*... -
Page 29: Liftrack
LIFTRACK For configuration and use of the 4G.evox in conjunction with LifTrack please refer to the guides LifTrack and e-stant web available from the following Internet address: http://webshare.esse-ti.it/LifTrack.zip Page 29... -
Page 30: Signals
Dialling It indicates that 4G.evox is ready for dialing Dissuasion It indicates that 4G.evox has not properly registered with the mobile provider or a delay in dialling or the end of conversation or an access to services not permitted Busy... -
Page 31: Calls Signals
It indicates an incoming call Device status indicator LED (RED) It may indicate that 4G.evox has not been correctly registered with the network, the SIM card is protected by the PIN code or other problems It indicates 4G.evox is correctly registered to the network... -
Page 32: Power Supply Status Indicator Led (Blue)
Power supply status indicator LED (BLUE) It indicates that the external power supply is connected and the battery has max capacity charge It indicates that the external power supply is connected and the battery has good capacity charge It indicates that the external power supply is connected and the battery has medium capacity charge It indicates that the external power supply is connected and the battery has low capacity charge... -
Page 33: Lte/Umts/Gsm Signal Indicator Led (Green)
4G LTE/UMTS/GSM signal indicator LED (GREEN) No signal Low signal level (2G/3G network) Medium signal level (2G/3G network) Good signal level (2G/3G network) High signal level (2G/3G network) Low signal level (4G network) Medium signal level (4G network) Good signal level (4G network) High signal level (4G network) It indicates the SIM card is protected by the PIN code It indicates the SIM card is protected by the PUK code... -
Page 34: Problem-Detection Guide
The autodialer connected to Increase the voltage by the Telephone line voltage on TEL 4G.evox does not detect the programming “Telephone line terminals is insufficient telephone line voltage” The autodialer connected to... -
Page 35: Eu Declaration Of Conformity
EU DECLARATION OF CONFORMITY Hereby, Esse-ti S.r.l. declares that the equipment type 4G.evox is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available from the following Internet address: https://www.esse-ti.it/en/dichiarazioni-di-conformita Page 35... - Page 36 4G.evox 29/04/2022 Esse-ti S.r.l. Via G. Capodaglio, 9 – 62019 Recanati (MC) – ITALY Tel. +39 0717506066 – Fax +39 0717506057 www.esse-ti.it – e-mail: support@esse-ti.it...
Need help?
Do you have a question about the 4G.evox and is the answer not in the manual?
Questions and answers