Related Manuals for Ebyte E83-2G4M03S
Summary of Contents for Ebyte E83-2G4M03S
- Page 1 Chengdu Ebyte Electronic Technology Co., Ltd. E83-2G4M03S User Manual E83-2G4M03S User Manual nRF5340 2.4GHz BLE 5.2 Module...
-
Page 2: Table Of Contents
7 Soldering ........................................14 7.1 Reflow temperature ..................................14 7.2 Reflow Soldering Curve ................................15 8 Similar Models ......................................15 9 Standard Packing info ....................................16 Revision History ......................................16 About ..........................................17 Copyright ©2012 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 3: Disclaimer And Copyright Notice
Technology Co., Ltd. reserves the right to modify the contents of this manual without any notice or prompt. This manual is only used as a guide . Chengdu Ebyte Electronic Technology Co., Ltd. does its best to provide accurate information in this manual. However, Chengdu Ebyte Electronic Technology Co., Ltd. does not ensure that the contents of the manual are completely error-free. -
Page 4: Overview
NRF5340 introduces most of the I/O ports to facilitate users' all-round development. E83-2G4M03S is a hardware platform, the module has no program by default, and users need to develop firmware; please refer to the official Datasheet for nRF5340 chip information, and the module has maximized the RF characteristics of the chip. -
Page 5: Parameters
1 Mbps / 1 Mbps BLE receive current RX only run current (DC/DC, 3 V) 2 Mbps / 2 Mbps BLE RX only run current LDO,3V, 2 Mbps / 2 Mbps BLE Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. - Page 6 Dual core 128/64 MHz ARM ® kernel Cortex ® - M33 Dimensions 1 6.0 * 1 6.0mm _ ±0.1mm Antenna interface Generation 1 IPEX Equivalent impedance is about 50Ω product weight 1.2g ±0.1 g Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd.
-
Page 7: Size And Pin Definition
USB D+; D+ data line directly connected to the UBS bus (see input Output nRF5340 manual for details) USB power supply, range 4.35V-5.5V (see nRF5340 manual for VBUS enter details) Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. - Page 8 Configurable general-purpose IO port ; I²C bus interface (see P1.02/I²C input Output nRF5340 manual for details) P0.08/TRACEDATA3/SC Configurable general-purpose IO port ; trace buffer input Output TRACEDATA[3]; SPIM4 (see nRF5340 manual for details) Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd.
- Page 9 Configurable general-purpose IO port ; analog input (see P0.27/AIN6 input Output nRF5340 manual for details) P0.17/QSPI_CLK input Output Configurable general-purpose IO port ; queue serial peripheral Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd.
-
Page 10: Firmware Flashing
The nFR5340 only supports nrfconnect sdk Official download link: https://academy.nordicsemi.com/lessons/lesson-1-nrf-connect-sdk-introduction/ For detailed environment installation tutorial, please refer to Nordic official: https://academy.nordicsemi.com/topic/exercise-1-1/ 2. Chip manual Official download link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fstruct_nrf53%2Fstruct%2Fnrf5340.html 4.2 Program burning Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. - Page 11 2. Use the Programmer tool in the official burning tool nRF Connect Desktop to burn the program, or use the VSCODE tool to burn the program. The official website tool can be downloaded at: https://www.nordicsemi.com/Products/Development-tools/nrf-connect-for-desktop Flashing program Ebyte EVB Not available for the moment. Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd.
-
Page 12: Developer Notes
If it is absolutely necessary to pass under the module, assuming that the module is soldered on the Top Layer, the top layer of the contact part of the module should be Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 13: Faq
6.2 Module is easily damaged Please check the power supply to ensure that it is between the recommended supply voltages, if exceeding the maximum value will cause permanent damage to the module; Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 14: Bit Error Rate Is Too High
If the power supply is not ideal, it may also cause garbled characters. Be sure to ensure the reliability of the power supply; Poor quality or too long extension cables and feeders can also cause high bit error rates. Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 15: Soldering
Time from room temperature to peak 6 minutes, maximum 8 minutes, maximum temperature ※The peak temperature (Tp) tolerance definition of the temperature profile is the upper limit of the user Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 16: Reflow Soldering Curve
E73-2G4M04S1 nRF52810 2.4G 4.2/5.0 17.5*28.7 patch PCB/IPX E73-2G4M04S1 nRF52832 2.4G 4.2/5.0 17.5*28.7 patch PCB/IPX nRF5340 Ceramic E83-2G4M03S 2.4G 4.2/5.0 16 * 16 patch Antenna E73-2G4M04S1 nRF51822 2.4G 17.5*28.7 patch PCB/IPX Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 17: Standard Packing Info
Chengdu Ebyte Electronic Technology Co., Ltd. E83-2G4M03S User Manual 9 Standard Packing info Revision History Version revision date Revision Notes Maintenance man 2022-09-29 initial version 2023-02-23 Error correction Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd. -
Page 18: About
E83-2G4M03S User Manual About Sales Hotline: 4000-330-990 Company Tel: 028-61543675 Technical support: support@cdebyte.com Official website: https://www.cdebyte.com Company address: Building B5, 199 West Avenue, Gaoxin West District, Chengdu City, Sichuan Province, China Copyright © 2002 , Chengdu Ebyte Electronic Technology Co., Ltd.