Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Epson PowerLite Pro Cinema 9350
Summary of Contents for Epson PowerLite Pro Cinema 9350
- Page 1 ® PowerLite Pro Cinema 9350/9700 UB Home Theater Projector User’ s Guide...
-
Page 2: Copyright Notice
Epson product. Epson is not responsible for any use of this information as applied to other products. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to... -
Page 3: Table Of Contents
Contents Introduction Projector Parts Remote Control Optional Accessories Registration and Warranty Using This Manual Setting Up the Projector Choosing a Location Installing the Projector Connecting the Cables Connecting Video and Computer Equipment Making Other Connections Installing Batteries in the Remote Control Turning the Projector On and Off Turning On the Projector Turning Off the Projector... - Page 4 Making Detailed Adjustments Using the Menu System Changing How the Menus Display Adjusting the Picture Quality Input Brightness Settings Sharpness and Picture Quality Settings Color Settings Adjustments for Computer Images Selecting Memory Settings and Resetting the Projector Selecting Memory Settings Creating Memory Settings Renaming Memory Settings Deleting Saved Memory Settings...
- Page 5 Solving Remote Control Problems Where to Get Help Specifications General Lamp Remote Control Dimensions Electrical Environmental Safety Compatible Video Formats ESC/VP21 Command Codes Notices Important Safety Information FCC Compliance Statement Declaration of Conformity Epson America, Inc. Limited Warranty Index Contents...
-
Page 6: Introduction
Auto Iris system that constantly controls the light output based on the gamma and black/white levels of your projected content, for perfectly adjusted images and deepest blacks ■ Epson C Fine ® 3LCD technology for reliable picture quality, increased contrast ratio and uniform colors ■... -
Page 7: Projector Parts
Projector Parts Front Lamp cover Ventilation slots Horizontal lens shift dial Back Component video port HDMI ports Air intake (filter) Control panel (top) Focus ring Lens cover Infrared receiver S-Video port Video port Cable holder Vertical lens shift dial Control panel (side) Zoom ring Infrared receiver... -
Page 8: Projector Control Panel
Bottom Mounting bracket attachment points Optional cable cover attachment points (brass colored) Projector Control Panel Top control panel Power button Source button Switches the video input source Warning lights Introduction Side control panel Menu button Enter button Displays the Selects menu items or menus opens the line menu Menu navigation... -
Page 9: Remote Control
Remote Control Power button Turns projector on or off Default button Restores default settings when menu is displayed Menu navigation buttons Memory button Recalls custom picture settings RGBCMY button Adjusts the hue, saturation, and brightness for each color Gamma button Adjusts the gamma values of the screen display Pattern button... -
Page 10: Optional Accessories
Your projector comes with a basic three-year carry-in warranty. For details, see page 74. In addition, Epson offers free Extra Care equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada. See your Extra Care Home Service brochure for details. -
Page 11: Using This Manual
Note: Contains important information about your projector. Tip: Contains helpful projection tips. Need additional help? Take advantage of Epson’s automated support services 24 hours a day at epson.com/support (U.S.) or epson.ca/support (Canada). Use this site to view FAQs (Frequently Asked Questions) or product information and e-mail your questions to Epson support. -
Page 12: Setting Up The Projector
Setting Up the Projector Follow the instructions in this section to choose a location for the projector, connect the cables, and display an image. Choosing a Location You can install the projector for the viewing setups shown below, as well as rear projection. Center Side Ceiling... - Page 13 Ideally, keep the projector level and place it at a height so its lens is centered between the top and bottom of the screen, as shown below. If this is not possible, use the lens shift dials to reposition the image. As a rule of thumb, you can use lens shift to move the image up or down by nearly its full height, and left or right by about one-half its width (for details, see page 25).
- Page 14 The size of the image is determined by the distance from the projector’s lens to the screen. Depending on your display settings and how you use the Zoom ring, the actual size may differ. Use these tables as a guide for projector placement: 16:9 aspect ratio Projection distance 2.8 to 6.2 feet...
- Page 15 To determine the exact image size when you know the projection distance (or the exact projection distance when you know the desired image size), you can use the Image Size Calculator. This program is available on the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada).
-
Page 16: Installing The Projector
Front/Ceiling 4. Press the button when done. Menu Note that you can rotate the Epson logo plate 180 degrees when suspending the projector from a ceiling. If you are planning to use an AV controller with the projector, refer to the table of ESC/VP21 command codes on page 69. - Page 17 The following illustrations show the dimensions of the projector: 5.4 in. 36 mm 0.5 in. 2.3 mm M4×9mm 0.2 in. 4.5 mm 131 mm 17.7 in. 450 mm 11.8 in. 300 mm 5.9 in. 150 mm 2.2 in. 56 mm 1.8 in.
-
Page 18: Connecting The Cables
Connecting the Cables Connecting Video and Computer Equipment You can connect the projector to many types of video equipment, such as a Blu-ray ™ Disc /DVD player, digital tuner, cable or satellite box, video game console, camcorder, or digital camera. You can also connect it to a desktop or laptop PC or Apple system. - Page 19 For best results, connect your video equipment to the equipment doesn’t support HDMI, connect it to one of the following ports (highest quality listed first): (for component video), Component When you connect a large or heavy cable to the projector, such as an HDMI cable, it is recommended that you fasten it to one of the two cable holders using a commercially available cable tie.
-
Page 20: Making Other Connections
Making Other Connections Connect the power cable and other cables described below, depending on how you plan to use the projector. ■ Plug the power cable into the projector and a grounded electrical outlet. ■ Trigger out when the projector is turned on. This lets a central control system monitor whether the projector is on or off, and can be used to raise or lower your projection screen automatically when the projector... -
Page 21: Installing Batteries In The Remote Control
Installing Batteries in the Remote Control The remote control uses two AA batteries. WARNING: Keep batteries away from children. If a battery is swallowed, contact your doctor immediately. 1. Release the tab and lift open the cover. 2. Insert two new AA batteries as shown. 3. -
Page 22: Turning Off The Projector
4. Press the Ppower button on the remote control or projector. Note: To prevent children from turning on the projector, you can use the Child Lock feature. See page 32 for details. If you’ll be using the projector at an altitude above 4921 feet (1500 meters), turn on High Altitude Mode so the fan can properly cool the projector at the high altitude air pressure. -
Page 23: Selecting The Image Source
Selecting the Image Source The source buttons on the projector and remote control let you switch between images from different pieces of equipment connected to the projector (such as a Blu-ray Disc/DVD player, cable or satellite box, or video game console). Press the button on the remote control that corresponds to the port to which your Source... -
Page 24: Positioning The Image
Positioning the Image If the image is not centered on the screen, use the horizontal and vertical lens shift dials to adjust its position. Caution: Do not try to move the lens by hand, or you may damage the projector. Always use the lens shift dials to change the lens position. - Page 25 The image cannot be moved to the maximum distance in both the vertical and horizontal directions. For example, the image cannot be shifted vertically when it has been shifted horizontally by the full amount. When the image has been shifted vertically by the full amount, it can be shifted up to 9 percent of the width of the image.
-
Page 26: Making Basic Adjustments
Making Basic Adjustments Follow the instructions in this chapter to make basic adjustments to the image shape, size, color, and quality. For further refinements, see “Making Detailed Adjustments” on page 33. Focusing and Zooming Use the focus ring to sharpen the image. Use the zoom ring to reduce or enlarge the image. -
Page 27: Choosing The Aspect Ratio
Choosing the Aspect Ratio In many cases, video signals are automatically resized to fit on your screen when is selected as the Aspect setting. Auto You may need to change the size of the image (or aspect ratio) for certain image types by pressing the on the remote control. -
Page 28: Choosing The Color Mode
Note: When displaying 720p, 1080i, or 1080p signals through the HDMI or Component video port, the aspect ratio is automatically selected and you cannot change it. If you display a 4:3 image using the Zoom setting, the top and bottom will be cut off. You can use the Zoom Caption Pos. -
Page 29: Advanced Color Adjustments
The built-in Epson Cinema Filter automatically improves color reproduction in a darkened room; it is not used when you select (Pro Cinema 9700 UB) or (Pro Cinema Vivid Dynamic 9350) or (Pro Cinema 9700 UB) or (Pro Cinema 9350). Cinema Day... -
Page 30: Adjusting The Gamma Setting
Adjusting the Gamma Setting You can select from five gamma settings (2.0 to 2.4) or customize your own setting from your image or a displayed graph. Lower values will increase the contrast of dark areas, but tend to blur the bright areas. Higher values will darken the light areas. Gamma presets make minor adjustments to mid-tone values. -
Page 31: Adjusting Rgbcmy
Adjusting RGBCMY Use this feature to adjust the hue, saturation, and brightness for each of the red (R), green (G), blue (B), cyan (C), magenta (M), and yellow (Y) color components. 1. Press the button. You see the following displayed on the screen: RBGCMY 2. -
Page 32: Locking The Projector
Locking the Projector The projector includes two lock settings to prevent the image from being accidentally changed once it’s adjusted, and to keep children from turning on the projector without adult supervision. To access the lock settings, follow these steps: 1. -
Page 33: Making Detailed Adjustments
Making Detailed Adjustments You can use the projector’s on-screen menus to make detailed adjustments to the image quality—such as the brightness, contrast, sharpness, and color. You can also change the menu display, sleep mode settings, and other projector features. Using the Menu System You can access the menu system either from the remote control or the buttons on the projector’s control panel. - Page 34 3. Press the u, d, l, or r button to change settings as necessary. You may have to press the button to confirm your choice. Enter 4. When you’re finished, press the button to exit the menu system. Menu To display one of the line menus, press the bottom of the image: 1.
-
Page 35: Changing How The Menus Display
Changing How the Menus Display Use these options to control how the menus display. ■ Language Settings > Language Select from 21 languages to use in the menu system. ■ Menu Position Settings > Display > Menu Position Use the arrow buttons to choose a position on the screen for displaying the menu. ■... - Page 36 ■ EPSON Super White Signal > Advanced > EPSON Super White Note: This setting can be used only when a composite video, S-Video, or component video signal is being input and the Color Mode is set to THX (Pro Cinema 9700 UB), Natural (Pro...
-
Page 37: Sharpness And Picture Quality Settings
■ HDMI Video Range Signal > Advanced > HDMI Video Range Note: This setting can be used only when HDMI1 or HDMI2 is selected as the image source (see page 23). This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). -
Page 38: Noise Reduction
■ Progressive Signal > Progressive Converts interlaced to progressive signals. The projector uses 3D DigiScan Circuitry Processing for video-sourced images. For film-sourced images, you can select from 2-2, 2-3, or 4-4 pulldown detection, depending on your model. Leave the setting on output. - Page 39 ■ Block NR (Pro Cinema 9700 UB only) Signal > Advanced > Block NR Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28) or with a signal input through the PC port. This setting reduces block noise that can appear when projecting MPEG images that have been compressed at a low bit rate.
-
Page 40: Color Settings
Color Settings If the image colors don’t look correct, you can adjust them using these settings. Use the first three settings described below to make the most visible changes. If you only need to make slight adjustments, you can fine-tune the picture with the remaining settings. Most color settings are stored separately for each image source and color mode. - Page 41 ■ RGB Image > Advanced > RGB Note: This setting cannot be used when the Color Mode is set to x.v.Color (see page 28). Use the RGB settings to fine-tune the color of the image. You can adjust the offset and gain for each signal color (red, green, and blue).
-
Page 42: Adjustments For Computer Images
■ Color Gamut (Pro Cinema 9700 UB only) Image > Advanced > Color Gamut Note: The Color Gamut setting can only be used when the Color Mode is set to THX (see page 28). You can select from three different color gamut settings according to the source material and locale. -
Page 43: Selecting Memory Settings And Resetting The Projector
■ Tracking Signal > Tracking Adjust the tracking to eliminate vertical bands. It is easiest to adjust the tracking when the image contains a lot of fine detail (such as black text on a white background). ■ Sync. Signal > Sync. Adjust the synchronization to eliminate blurriness. -
Page 44: Creating Memory Settings
Creating Memory Settings Memory settings can be used to store most of the picture quality settings on page 37 and color settings on page 40. Before saving them to memory, adjust the settings to the desired levels. 1. Press the Memory 2. -
Page 45: Deleting Saved Memory Settings
Deleting Saved Memory Settings You can clear all your memory settings at once. 1. Press the button on the remote control. Menu 2. Open the menu, then select Reset 3. Select , then press the Note: You can delete memory settings one at a time with the Erase Memory setting under the Memory menu. -
Page 46: Customizing Projector Features
3. Do one of the following: ■ Select Reset Lamp Hours You should reset the lamp timer only when you install a new projector lamp. See page 56 for more information. ■ Select Reset Memory ■ Select Reset All Component, Save Memory, Language, and Lamp Hours). Customizing Projector Features Use the settings in this section to adjust the image size and position, suppress on-screen text, and select basic setup options. -
Page 47: Screen Options
■ Zoom Caption Pos. Signal > Zoom Caption Pos. Lets you adjust the shape and position of the image so that subtitles are visible (available only if the aspect ratio has been set to of the image, and Zoom Caption Pos. before changing the zoom position. -
Page 48: Video Signal
■ Video Signal Settings > Input Signal > Video Signal Leave this setting on NTSC or PAL (for standard TV formats). ■ Component Settings > Input Signal > Component Change this setting to match the type of equipment connected to the Component port. For component video, select or select YCbCr... -
Page 49: High Altitude Mode
■ Control Panel Lock Settings > Control Panel Lock Lets you disable all the buttons on the projector’s control panel to prevent the image from being accidentally changed once it is adjusted. See page 32 for more information. ■ High Altitude Mode Settings >... -
Page 50: Maintenance
Maintenance Your projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. You also may need to clean the air filter to prevent overheating. WARNING: Before you clean any part of the projector, turn it off and unplug the power cord. Never open any cover on the projector, except the lamp and filter covers. -
Page 51: Cleaning The Projector Case
Cleaning the Projector Case Before you clean the case, turn off the projector and unplug the power cord. ■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth. ■ To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral detergent. - Page 52 If the dirt is difficult to remove or the filter is broken, replace it. You can purchase air filter part number V13H134A21 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).
-
Page 53: Replacing The Lamp
Turn off this product when not in use to prolong the life of the projector. You can purchase lamp part number V13H010L49 from an authorized Epson reseller. To find the nearest reseller, please call 800-GO-EPSON (800-463-7766). To purchase online, visit www.epsonstore.com (U.S. - Page 54 5. Insert the screwdriver that came with the lamp (or a similar tool) into the slot on the back of the projector to release the lamp cover. Then lift up the cover to remove it. 6. Loosen the two screws securing the lamp (they don’t come all the way out). 7.
- Page 55 8. Gently insert the new lamp and tighten its screws. Caution: Don’t touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure. 9. Replace the lamp cover. (The projector won’t work if the lamp cover is open or loose.) 10.
-
Page 56: Resetting The Lamp Usage Timer
Resetting the Lamp Usage Timer After replacing the lamp, plug the projector back in, turn on the power switch on the back, and press the Ppower button. Then follow these steps to reset the lamp usage timer: 1. Press the button on the projector or remote control. -
Page 57: Storing The Projector
Pack the projector in its original packaging or equivalent. Transporting the Projector Note: Epson shall not be liable for any damages incurred during transportation. The projector contains many glass and precision parts. When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials. -
Page 58: Problem Solving
Problem Solving This section explains how to interpret the projector’s status lights, solve problems with the picture and remote control, and contact technical support. What To Do When the Lights Come On or Flash The lights on top of the projector indicate the projector’s status and let you know when a problem occurs. - Page 59 There is an internal problem. Turn off the power switch on the back of the projector, and unplug it from the electrical outlet. Then contact Epson for assistance (see page 64). There is a fan or sensor problem. Turn off the power switch on the back of the projector, and unplug it from the electrical outlet.
-
Page 60: Solving Picture Problems
Solving Picture Problems You cannot turn on the projector. ■ Make sure the power cord is connected and the power switch in back of the projector is turned on. Then wait a moment for the Ppower light to come on before pressing the Ppower button. - Page 61 You’re using a computer and no picture appears on the screen. ® If you’re using a Windows laptop: ■ Press the function key that lets you display on an external monitor. It’s often labeled with an icon such as , but it may also be labeled key while pressing it.
- Page 62 The picture isn’t rectangular. ■ If the image looks like screen and angled toward it. Face the projector straight ahead (instead of at the center of the screen), then use the horizontal lens shift dial to center the image (see page 24). ■...
-
Page 63: Solving Remote Control Problems
■ Fine-tune the colors with the settings listed on page 40. ■ If the picture looks dark, you may need to replace the lamp. Check the lamp usage timer to see how long the lamp has been in use (see page 56). Replace the lamp if it’s close to the end of its service life (see page 53). -
Page 64: Where To Get Help
Speak to a Support Representative To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector. This is the fastest way of speaking to a live representative, and it’s free. -
Page 65: Specifications
Specifications General Type of display Poly-silicon TFT active matrix Size of LCD panels 0.74 inch (18 mm) wide Lens F=2.0 to 3.17 Resolution (native format) 1920 × 1080 pixels, 1080p Brightness Pro Cinema 9350: Normal mode: White light output 2000 lumens (ISO 21118 standard) Color light output 2000 lumens Pro Cinema 9700 UB: Normal mode:... -
Page 66: Remote Control
Remote Control Range Batteries Dimensions Height Width Depth Weight Electrical Rated frequency Power supply Power consumption Specifications Approximately 30 feet (9 m) AA × 2 5.4 inches (136 mm), not including adjustable feet 17.7 inches (450 mm) 14.2 inches (360 mm); not including lens protrusion 16.1 lb (7.3 kg) (Pro Cinema 9350) 16.5 lb (7.5 kg) (Pro Cinema 9700 UB) 50/60 Hz AC... -
Page 67: Environmental
Environmental Temperature Operating: 41 to 95 °F (5 to 35 °C) Storage: 14 to 140 °F (–10 to 60 °C) Humidity Operating: 20 to 80% RH, non-condensing Storage: 10 to 90% RH, non-condensing Operating altitude Up to 7500 feet (2286 meters); over 4921 feet (1500 meters), enable High Altitude mode in the Settings menu (see page 49) Safety... - Page 68 Component video Format/ Signal SDTV 480i 576i 480p 576p HDTV 720p 1080i 1080p Analog RGB (computer display) Signal SVGA SXGA WXGA MAC13” MAC16” MAC19” MAC21” HDMI Signal SDTV 480i 576i 480p 576p HDTV 720p 1080i 1080p Specifications Refresh rate (Hz) Resolution 720 ×...
-
Page 69: Esc/Vp21 Command Codes
You can use an AV controller with a 9-pin null modem serial cable to control the projector. You can download the complete ESC/VP 21 Communication Manual for home theater projectors from the Epson website at epson.com/support (U.S.) or epson.ca/support (Canada). Following are some of the available codes:... - Page 70 Item Aspect ratio Specifications Normal Full Zoom Wide Anamorphic Wide (Pro Cinema 9700 UB) Horiz. Squeeze (Pro Cinema 9700 UB) Command ASPECT 00 ASPECT 40 ASPECT 50 ASPECT 70 ASPECT 80 ASPECT 90...
-
Page 71: Notices
Notices Important Safety Information Follow these safety instructions when setting up and using the projector: ■ Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes. Never let children look into the lens when it is on. ■... - Page 72 ■ The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash. ■ Allow the lamp to cool for one hour before replacing it. ■ Unplug the projector during lightning storms or when not in use for extended periods. ■...
-
Page 73: Fcc Compliance Statement
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. -
Page 74: Declaration Of Conformity
What Epson Will Do To Correct Problems: If your product requires service during the limited warranty period, please call Epson at the number on the bottom of this statement and be prepared to provide the model, serial number, and date of original purchase. Epson will, at its option, repair or replace the defective unit, without charge for parts or labor. - Page 75 Epson product for carry-in warranty service are your responsibility. Epson will pay for all freight charges if you choose to send your unit to Epson for repair. If a claimed defect cannot be identified or reproduced in service, you will be held responsible for costs incurred.
-
Page 76: Index
Index Numerics 2-2 Pull-down, 39 4-4 Pull-down, 39 Abs. Color Temp. setting, 40 Accessories, 10, 64 Air filter cleaning and replacing, 51 to 52 ordering, 10 Anamorphic lens, 20, 27 Anamorphic Wide setting, 27 Anti-theft device, 7, 10 Aspect button, 9, 27, 28, 60 Aspect ratio, selecting, 27 to 28, 46 Auto Iris setting, 36 Auto Setup, 42... - Page 77 10, 64 Home Service, 10 PrivateLine Support, 11, 64 technical support, 11, 64 warranty, 10, 74 to 75 EPSON Super White setting, 36 ESC/VP21 command codes, 69 FCC Compliance Statement, 73 Filter, see Air filter Flickering, 38, 62 Focus ring, 26...
- Page 78 Memory button, 9, 43 Memory settings creating, 44 renaming, 44 using, 43 Menu button, 9, 33 Menus available settings, 35 to 49 customizing display, 35 line menu, 9 using, 33 to 35 Message setting, 47 Mosquito NR, 38 Motion Detection, 38 Mounting projector, 16 Moving projector, 57 No image, 60 to 61...
- Page 79 Skin Tone setting, 40 Sleep mode, 48 Source buttons, 8, 9 Source, selecting image, 23 Specifications compatible video formats, 67 to 68 dimensions, 66 electrical, 66 environmental, 67 general, 65 lamp, 65 remote control, 66 Startup screen, selecting, 47 Static, 62 Storing projector, 57 Super-resolution, 42 Support, 11, 64...