Table of Contents

Advertisement

Available languages

Available languages

Ver 1_ES_EN
MANUAL DEL USUARIO Y DEL INSTALADOR
Estimado cliente, le agradecemos la confianza depositada en nuestra empresa al comprar este
producto.
Por favor, antes de instalar o utilizar el aparato por primera vez, lea atentamente estas
instrucciones.
Este Termo Eléctrico ha sido fabricado de acuerdo con los estándares de calidad más exigentes y
siguiendo lo establecido en las Normas Europeas de Seguridad Eléctrica y Compatibilidad Electromagnética. Las
características técnicas del aparato están indicadas en la placa de características situada en la parte posterior de
la tapa inferior de los termos.
La instalación debe ser llevada a cabo por personal cualificado. Cualquier trabajo de reparación o
mantenimiento (eliminación de incrustaciones calcáreas, cambio o revisión de ánodo, etc...) debe ser
llevado a cabo por Servicios de Asistencia Técnica Autorizados por APARICI.
Información técnica:
MODELO
CAPACIDAD
VOLTAJE (V CC)
POTENCIA (W)
CLASE
GRADO DE
PROTECCIÓN
Tª REGULACIÓN
TERMOSTATO(ºC)
TIPO DE
TERMOSTATO DE
REGULACIÓN
TIPO DE
TERMOSTATO DE
SEGURIDAD
REGULACIÓN
EXTERIOR
TIPO DE
RESISTENCIA
DEPÓSITO
ESMALTADO
ÁNODO DE
MAGNÉSIO
P. NOMINAL
P. VÁLVULA
APARICI – SOLxxxN
MANUAL DEL INSTALADOR
SOL050
SOL075
50
CARACTERÍSTICAS ELÉCTRICAS:
60 / 120
60 / 120
530 / 1060
530 / 1060
I
IPX4
65
BULBO
BULBO
BULBO
BULBO
SI
BLINDADA
BLINDADA
BAJO VAINA
BAJO VAINA
CARACTERÍSTICAS HIDRÁULICAS:
SI
SI
9 bar
10 bar
DIMENSIONES
MODELO
SOL050
G1/2'
TOMAS DE
AGUA
SOL100
75
100
60 / 120
530 / 1060
I
I
IPX4
IPX4
65
65
BULBO
BULBO
SI
SI
BLINDADA BAJO
VAINA
SI
SI
SI
SI
9 bar
9 bar
10 bar
10 bar
SOL075
SOL100
SOL120
G1/2'
G1/2'
1
SOL120
120
60 / 120
530 / 1060
I
IPX4
65
BULBO
BULBO
SI
BLINDADA BAJO
VAINA
SI
SI
9 bar
10 bar
G1/2'

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SOL Series and is the answer not in the manual?

Questions and answers

Mercedes
March 2, 2025

En que posición hay que poner el botón lateral para poner el termo en modo eco?

User image 67c432538347b
1 comments:
Mr. Anderson
March 2, 2025

The manual states that the thermostat used in the Aparici SOL Series allows temperature regulation and includes an "ECO" position. To set the thermostat to eco mode, turn the side button to the position labeled "ECO," which corresponds to a specific approximate water temperature inside the tank.

This answer is automatically generated

Summary of Contents for Aparici SOL Series

  • Page 1 La instalación debe ser llevada a cabo por personal cualificado. Cualquier trabajo de reparación o mantenimiento (eliminación de incrustaciones calcáreas, cambio o revisión de ánodo, etc...) debe ser llevado a cabo por Servicios de Asistencia Técnica Autorizados por APARICI. MANUAL DEL INSTALADOR Información técnica:...
  • Page 2 2.- ANCLAJE DEL APARATO Por su diseño, los termos eléctricos APARICI de estas series están previstos para ser instalados en tres posiciones, según se observa en las figuras 2.1, 2.2 y 2.3.
  • Page 3: Conexión Hidráulica

    Ver 1_ES_EN Fig. 2.2 3. Horizontal tapa de registro a la derecha. En esta posición la entrada de agua fría (F) se realiza por el tubo inferior y la de la caliente por el superior (C). Sin embargo, por la configuración del aparato, la primera operación a realizar para instalar el mismo, es intercambiar los tubos roscado de entrada (difusor) y salida del termo, situando el de la derecha en la izquierda y viceversa (visto el termo en posición vertical).
  • Page 4: Conexión Eléctrica

    Ver 1_ES_EN Puesta en servicio: Antes de conectar hidráulicamente el termo, dejar fluir el agua durante unos minutos a fin de que se elimine cualquier cuerpo extraño que haya en las tuberías, el cual pueda obstruir o dañar la válvula de seguridad alterando el funcionamiento de la misma.
  • Page 5 Ver 1_ES_EN Fig. – 5 Esquema unifilar modelo APARICI SOLxxx Montaje de la resistencia adecuada en función del campo de colectores empleado ¡IMPORTANTE! Este trabajo debe ser realizad por personal competente. En ningún caso debe ser realizado por el usuario.
  • Page 6 Ver 1_ES_EN c. Quitar el mando de regulación. d. Despegar la etiqueta frontal del termo. e. Desconectar el piloto de 30V-530W y retirarlo. A continuación montar el nuevo piloto de 60V-1060W. Pegar una nueva etiqueta frontal...
  • Page 7 Ver 1_ES_EN g. Montar el mando de regulación. h. Cerrar la tapa del termo. Proceder a la conexión del termo al campo de colectores según e indica en la figura 4. 5.- NORMATIVA DE CONEXIÓN ELÉCTRICA. La instalación eléctrica del termo, está regulada por las normas específicas incluidas en el Reglamento Electrotécnico para baja tensión y la norma CEI 64-8.
  • Page 8: Recomendaciones De Instalación

    APARICI recomienda la instalación de una válvula reductora de presión, regulada entre 2.5 y 3 bar, y un vaso de expansión. La válvula reductora de presión debe de instalarse lo más cerca posible de la acometida de la vivienda y alejada, a su vez, de la entrada del agua al aparato.
  • Page 9: Condiciones De Garantía

    A partir de los primeros 6 MESES, APARICI le prolonga la garantía hasta los DOS AÑOS desde la fecha de entrega amparándose en la presente Garantía Comercial. Durante este periodo, el Servicio Técnico Oficial determinará...
  • Page 10 Ante la eventualidad de una avería, puede consultar la documentación de su aparato para ver cuál es el Servicio Técnico Oficial más cercano a usted, acceder a la página web de la empresa (www.aparici.es) o bien puede contactar al número de teléfono 93 474 24 23. Del mismo modo, si necesita hacer cualquier comunicación legal con nuestra empresa debe dirigirse a NOFER,S.L., Avenida de la Fama,118 08940 Cornellá...
  • Page 11: Electrical Characteristics

    Ver 1_ES_EN USER'S AND INSTALLATION MANUAL APARICI – SOLxxx Dear buyer, we thank you for purchase of our product. Prior to installation and first use of the electric water heater, please carefully read these instructions. This water heater has been manufactured in compliance with the relevant standards and tested by the relevant authorities as indicated by the Safety Certificate and the Electromagnetic Compatibility Certificate.
  • Page 12 2.- APPLIANCE WALL HANG Due to its particular design, the APARICI electrical water heaters could be installed in three positions as you could see at fig-2.1, 2.2 and 2.3: 1.
  • Page 13: Connection To The Water Supply

    Ver 1_ES_EN Fig. 2.1 2. Horizontal with maintenance cover on left side. In this case inlet cold water pipe (F) will be placed every time in the bottom pipe and hot water outlet pipe (C) in the upper part. The safety valve must be installed in the bottom pipe Fig.
  • Page 14 Ver 1_ES_EN Legend: 1- Return safety valve 6- Checking fitting 2- Checking valve connection 7- Funnel with outlet connection 3- Non-return valve 4- Pressure reduction valve F - Cold water 5- Closing valve C - Hot water Putting into service: Before connect hydraulically the water heater to water network lets the water flow some to time to remove all dirty which could damage the safety valve and block the diffuser.
  • Page 15 Ver 1_ES_EN The below drawing shows the electrical water heater diagram: Fig. – 5 APARICI – SOL electrical diagram. Installation of the appropriate heating element according to the collector field used IMPORTANT! This work must be carried out by competent personnel. In no case should it be done by the user.
  • Page 16 Ver 1_ES_EN c. Remove the regulation knob. d. Remove rthe front label. e. Disconnect the 30V-530W pilot light and remove it. Then assembly the new 60V-1060W pilot light. Paste the new front label.
  • Page 17 Ver 1_ES_EN g. Assembly again the regulation knob. h. Closet he maintenance cover.. Proceed to connect the water heater to the collector field as indicated in figure 4. 5.- ELECTRICAL CONNECTIONS STANDARDS. The electrical installation must fulfil the international standards CEI 64-8. According to these standards, electrical appliances must be installed following the below indications at bathrooms and WC: 1.- zone 0: Installation is totally forbidden at this area.
  • Page 18: Installation Recommendations

    Fig. – 6 6.- INSTALLATION RECOMMENDATIONS In order to have a correct operation of the APARICI electric water heater, please take into account the below considerations: 1. Water pressure at electric water heater inlet must be between 1.5 and 5 bar. Also all considerations explained at point 3) of this manual must be taken into account.
  • Page 19 Ver 1_ES_EN Position ‘+’: 65ºC. Maximum water temperature inside the tank. The operation of electric immersion heater is shown by pilot light. 2.- CLEANING. The external parts of the water heater may be cleaned with a mild detergent solution. Do not use solvents and abrasives.

This manual is also suitable for:

Sol050Sol075Sol100Sol120

Table of Contents

Save PDF