1. Manuals
  2. Brands
  3. Unverferth Manuals
  4. Farm Equipment
  5. Perfecta 10
  6. Manual

Unverferth Perfecta 10 Manual

Hide thumbs Also See for Perfecta 10:
Table of Contents

Advertisement

Quick Links

Download this manual
Seedbed Tillage
Rigid Perfecta
®
Folding Perfecta
up to 28'
®
Bedded Crop Perfecta
®
Models 10 / 12 / 14
Size 10'-28'
Serial Number A59300100 & Up
Part No. 74279

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Perfecta 10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Unverferth Perfecta 10

Summary of Contents for Unverferth Perfecta 10

  • Page 1 Seedbed Tillage Rigid Perfecta ® Folding Perfecta up to 28’ ® Bedded Crop Perfecta ® Models 10 / 12 / 14 Size 10’-28’ Serial Number A59300100 & Up Part No. 74279...
  • Page 2 FIELD CULTIVATORS — Introduction Foreword This symbol identifies important safety messages. When you see it, read the message that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them carefully and follow them closely when working around or using this machine.

  • Page 3: Product Information

    The information, specifications, and illustrations in the manual are on the basis of information available at the time it was written. Due to continuing improvements in the design and manu- facture of Unverferth products, all specifications and information contained herein are subject to change without notice.

  • Page 4: Table Of Contents

    FIELD CULTIVATORS — Introduction Table of Contents Foreword ............................2 Product Information ........................3 SECTION I Safety General Hazard Information ....................... 1-2 Safety Decals ..........................1-3 Following Safety Instructions ..................... 1-4 Before Servicing ......................... 1-4 Before Operating ........................1-5 During Operation ........................1-5 Before Transporting ........................
  • Page 5 FIELD CULTIVATORS — Introduction Table of Contents SECTION II Set Up General Set Up Information ....................... 2-3 Rigid Perfecta — Shipping Bundles ..................2-4 Folding Perfecta — Shipping Bundles ..................2-6 Bedded Crop Perfecta — Shipping Bundles ................2-8 Basic Set Up ..........................2-10 Mast Assembly .........................
  • Page 6 FIELD CULTIVATORS — Introduction Table of Contents SECTION III Operation General Operation Information ....................3-2 Preparing Tractor ........................3-2 Front-End Weights ....................... 3-2 Sway Blocks ........................3-2 Wheel Spacing ........................3-2 Tractor Quick Hitch ......................3-3 Tractor 3-Point Top Link Arm ..................... 3-3 Drawbar Position .........................
  • Page 7 FIELD CULTIVATORS — Introduction Table of Contents SECTION IV Maintenance Storage ............................4-2 Lubrication ..........................4-2 Wheel Bearings ........................4-2 Wing Assembly ........................4-2 Hub Assembly ..........................4-2 Replacing Single Rolling Harrow Basket Bearings ..............4-3 Replacing Double Rolling Harrow Basket Bearings ..............4-4 Installing Retaining Rings ......................
  • Page 8 FIELD CULTIVATORS — Introduction Table of Contents SECTION V Parts Mast Components with Square Truss Tubes ................5-2 Mast Components with Round Truss Tubes ................5-4 Main Frame – Rigid Perfecta ....................5-6 Main Frame – Folding Perfecta ....................5-8 Main Frame –...

  • Page 9: Section I

    — Safety FIELD CULTIVATORS SECTION I Safety General Hazard Information ....................... 1-2 Safety Decals ..........................1-3 Following Safety Instructions ..................... 1-4 Before Servicing ......................... 1-4 Before Operating ........................1-5 During Operation ........................1-5 Before Transporting ........................1-5 During Transport ......................... 1-6 Pressurized Oil ...........................

  • Page 10: General Hazard Information

    It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth Mfg. Co., Inc. ask that you be that kind of operator.

  • Page 11: Safety Decals

    — Safety FIELD CULTIVATORS Safety Decals PART NO. 95136 PART NO. 97961 PART NO. 95445 PART NO. 97972 PART NO. 900751 PART NO. 9829 PART #9003127 SMV EMBLEM AMBER REFLECTOR PART NO. 99507 PART #9003125 PART #9003126 FLUORESCENT REFLECTOR RED REFLECTOR...

  • Page 12: Following Safety Instructions

    — Safety FIELD CULTIVATORS Following Safety Instructions • Read and understand this operator’s manual before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts approved by the manufacturer.

  • Page 13: Before Operating

    — Safety FIELD CULTIVATORS Before Operating • Do not stand between towing vehicle and implement during hitching. • Always make certain everyone and everything is clear of the machine before beginning operation. • Verify that all safety shields are in place and properly secured. •...

  • Page 14: During Transport

    — Safety FIELD CULTIVATORS During Transport • Comply with all laws governing highway safety when moving machinery. • Use transport lights as required by all laws to adequately warn operators of other vehicles. • Use good judgment when transporting equipment on highways. Regulate speed to road conditions and maintain complete control.

  • Page 15: Preparing For Emergencies

    — Safety FIELD CULTIVATORS Preparing for Emergencies • Keep a first aid kit and properly rated fire extinguisher nearby. • Keep emergency numbers for fire, rescue, and poison control personnel near the phone. Wearing Protective Equipment • Wear clothing and personal protective equipment appropriate for the job. •...
  • Page 16 — Safety FIELD CULTIVATORS Notes...
  • Page 17 — Set Up FIELD CULTIVATORS SECTION II Set Up General Set Up Information ....................... 2-3 Rigid Perfecta — Shipping Bundles ..................2-4 Folding Perfecta — Shipping Bundles ..................2-6 Bedded Crop Perfecta — Shipping Bundles ................2-8 Basic Set Up ..........................2-10 Mast Assembly .........................
  • Page 18 — Set Up FIELD CULTIVATORS Notes...

  • Page 19: General Set Up Information

    — Set Up FIELD CULTIVATORS General Set Up Information This section contains all of the instructions required for the complete assembly of the entire field cultivator. For your safety, and the safety of others, use proper tools and equipment and always use safe working procedures.

  • Page 20: Rigid Perfecta - Shipping Bundles

    — Set Up FIELD CULTIVATORS Rigid Perfecta — Shipping Bundles...

  • Page 21: Rigid Perfecta - Shipping Bundles

    — Set Up FIELD CULTIVATORS Rigid Perfecta — Shipping Bundles ITEM PART NO. DESCRIPTION NOTES 71182 Spike One Bar 4’ Assembly For Rigid Perfecta Models 71183 Spike One Bar 5’ Assembly with Spike Leveler Option 71579B Spike One Bar 6’ Assembly 74670B Diagonal Bent Right-Hand “Y”...

  • Page 22: Folding Perfecta - Shipping Bundles

    — Set Up FIELD CULTIVATORS Folding Perfecta — Shipping Bundles...
  • Page 23 — Set Up FIELD CULTIVATORS Folding Perfecta — Shipping Bundles ITEM PART NO. DESCRIPTION NOTES 71181 Spike One Bar 3’ Assembly 71182 Spike One Bar 4’ Assembly For Folding Perfecta Models with Spike Leveler Option 71183 Spike One Bar 5’ Assembly 71579B Spike One Bar 6’...

  • Page 24: Bedded Crop Perfecta - Shipping Bundles

    — Set Up FIELD CULTIVATORS Bedded Crop Perfecta — Shipping Bundles...

  • Page 25: Bedded Crop Perfecta - Shipping Bundles

    — Set Up FIELD CULTIVATORS Bedded Crop Perfecta — Shipping Bundles ITEM PART NO. DESCRIPTION NOTES 71299 Spike One Bar 2’ Assembly 71182 Spike One Bar 4’ Assembly For All Bedded Crop Perfecta Models 71183 Spike One Bar 5’ Assembly 71579B Spike One Bar 6’...

  • Page 26: Basic Set Up

    — Set Up FIELD CULTIVATORS Basic Set Up Models 12 and 14, outer S-tines on each end of the machine are equipped with 2” wide point shovel. Units are shipped as shown to prevent damage to shovel in shipment. Point must be reversed before beginning operation.
  • Page 27 — Set Up FIELD CULTIVATORS Mast Assembly (continued) 5. Attach rear mast trusses (and side trusses on folding units). Brace Tube Weldment 1"-14UNS x 4" Capscrew (74860B) (9390-413) 1"-14UNS Elastic Jam Nut (9397-018) Remove Hardware FIG. 2-2 1"-14UNS x 3 1/2" Capscrew (9390-411) 1"-14UNS Elastic Jam Nut (9397-018) Front Strut Weldment...

  • Page 28: Wing Assembly

    — Set Up FIELD CULTIVATORS Wing Assembly 1. Using a safe lifting device rated at a minimum of 2,000 lbs., attach wings to the base using four 1 1/8" Dia. x 3 5/8" pins (82323), retain into position with four 3/8” Dia. x 2" spiral pins (91144-207) (Fig.

  • Page 29: Hydraulic Assembly

    — Set Up FIELD CULTIVATORS Hydraulic Assembly NOTE: Hydraulic cylinder should be installed with hydraulic ports facing up. 1. Install base end of hydraulic cylinder to the FIG. 2-6 OM-00316 main frame cylinder mount using a 1" Dia. x 3 3/4” pin (85632) and two 1/4" Dia. x 1 7/8" spiral pins (91144-165) (Fig.

  • Page 30: Hose Routing Diagram

    — Set Up FIELD CULTIVATORS Hydraulic Assembly (continued) HOSE ROUTING DIAGRAM For Main Frame Plumbing, Refer to PARTS Section for hoses, fitting types and position. To Tractor 32” Locking 15 1/2” Locking Cable Tie Cable Tie 2-14...

  • Page 31: Purging Hydraulic System

    — Set Up FIELD CULTIVATORS Hydraulic Assembly (continued) 3. Install hydraulic components to the machine. • Do not use any tape or thread sealant as all fittings have mechanical or O-ring seals. This pre- vents contamination from tape or thread sealants from entering the tractor's hydraulic system. NOTE: Refer to the "Hose Routing Diagram"...

  • Page 32: Hydraulic System Checks

    — Set Up FIELD CULTIVATORS Hydraulic Assembly (continued) Hydraulic System Checks ON ALL UNITS - CHECK THE FOLLOWING: ROUTING OF ALL HOSES: Hoses should not be kinked, twisted, or rubbing against sharp edges. FITTINGS AND CONNECTIONS: Check for leaks. Refer to "Torque Chart" in "MAINTENANCE" Section. HOSES Be sure hoses have room to "FLEX".

  • Page 33: Mounting Arm Assembly - Single Basket

    — Set Up FIELD CULTIVATORS Mounting Arm Assembly - Single Basket Assembly of the one-bar/Rolling Harrow baskets to the machine is best accomplished with the unit setting on the ground. See "Overhead Layouts" (on Positioning Components) in "ASSEMBLY" Section for dimensions showing mounting arm locations depending on style of leveler bar and harrow sizes and location on rear of the machine.

  • Page 34: Mounting Arm Assembly - Double Basket & Single Drum Roller

    — Set Up FIELD CULTIVATORS Mounting Arm Assembly - Double Basket & Single Drum Roller Assembly of the one-bar/Rolling Harrow baskets to the machine is best accomplished with the unit setting on the ground. See "Overhead Layouts" (on Positioning Components) in "ASSEMBLY" Section for dimensions showing mounting arm locations depending on style of leveler bar and harrow sizes and location on rear of the machine.

  • Page 35: Rolling Harrow Assembly - Single Basket

    — Set Up FIELD CULTIVATORS Rolling Harrow Assembly - Single Basket 1. Refer to table (below) for determining Rolling Harrow basket width required, on each section. ROLLING HARROW ROLLING HARROW WIDTH FRAME-WIDTH 35" 47" 59" 71" FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER •...

  • Page 36: Rolling Harrow Assembly - Double Basket

    — Set Up FIELD CULTIVATORS Rolling Harrow Assembly - Double Basket FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER • THE MACHINE AT ANY TIME WHILE BEING HOISTED. BE SURE ALL LIFTING DEVICES AND SUPPORTS ARE RATED FOR THE LOADS BEING HOISTED. THESE ASSEMBLY INSTRUCTIONS WILL REQUIRE SAFE LIFTING DEVICES UP TO 500 LBS.

  • Page 37: Drum Scraper Assembly

    — Set Up FIELD CULTIVATORS Drum Scraper Assembly • KEEP HANDS CLEAR OF PINCH POINT AREAS. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING THE IMPLEMENT. 1. Locate scrapers, bar mounts and hardware FIG. 2-13 bags.

  • Page 38: Drum Roller Assembly

    — Set Up FIELD CULTIVATORS Drum Roller Assembly • KEEP HANDS CLEAR OF PINCH POINT AREAS. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING THE IMPLEMENT. • FALLING OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH. DO NOT WORK UNDER THE MACHINE AT ANY TIME WHILE BEING HOISTED.

  • Page 39: Leveler Bar Assembly

    2. See Adjustments Section for procedure to adjust leveling bar tension. 3. Determine the style of leveler bar to be installed and follow instructions for that style. Unverferth Manufacturing does not recommend mixing leveler bar styles on a machine. See torque chart for proper tightening of all leveler bar hardware.

  • Page 40: Diagonal Tooth Leveler Bar

    — Set Up FIELD CULTIVATORS Leveler Bar Assembly (continued) LH Tooth (74676B) Locknut (9800) Diagonal Tooth Leveler Bar Flat Washer (91069PL) LH "Y" Tooth (74671B) Diagonal tooth leveler bars come in right-hand and left-hand assemblies. The teeth will point diagonally to the outside of the machine on each assembly. 1.

  • Page 41: Gauge Wheels

    — Set Up FIELD CULTIVATORS Gauge Wheels • For ease of assembly install hardware loosely until assembly is complete, then tighten all hard- ware. 1. Position gauge wheels onto the machine. Use the "Overhead Layouts" (on Positioning Components) in the Set Up Section to determine the wheel location on the cultivator frame.

  • Page 42: Transport Marking & Light Kits

    See federal regulation 49 CFR 562; available at www.govinfo.gov for US federal law requirements. See your Unverferth dealer for additional brackets, reflectors, or lights to meet your requirements. Lights & SMV Emblem for Rigid Perfecta Units Refer to “OVERHEAD LIGHT/REFLECTOR LAYOUTS” on the following pages for proper positioning of lights.

  • Page 43: Lights

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits (86763B & 86764B) Lights & SMV Emblem for Folding Perfecta Units Please refer to “OVERHEAD LIGHT/REFLECTOR LAYOUTS” on the following pages for proper positioning of lights. 1. Secure the left-hand light bracket (86770B) and right-hand light bracket (86769B) with amber round lights (9003876) and light bracket guard (78920B) with red round light (9003877) using 1/2”-13UNC U-bolts (96566) and 1/2”-13UNC lock nuts (9800) as shown in Fig.

  • Page 44: Overhead Layouts

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Overhead Layouts NOTE: Center All Reflectors Vertically On Tube 12' & 13' RIGID UNITS Amber Reflector (9003127) Amber Reflector (9003127) 3 1/4 3 1/4 2 1/4 Bracket & Amber Light SMV Emblem Bracket &...

  • Page 45: 14' & 15' Rigid Units

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Overhead Layouts 14' & 15' NOTE: Center All Reflectors Vertically On Tube RIGID UNITS Amber Reflector (9003127) Amber Reflector (9003127) 3 1/2 3 1/2 2 1/4 Bracket & Amber Light SMV Emblem Bracket &...

  • Page 46: 18' & 20' Rigid Units

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Overhead Layouts 18' & 20' RIGID UNITS NOTE: Center All Reflectors Vertically On Tube 2-30...

  • Page 47: Folding Unit Base

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Overhead Layouts ALL FOLDING UNIT (BASE) NOTE: Center All Reflectors Vertically On Tube Right-Hand Bracket & Amber Light Locate to the far end of the frame. Left-Hand Bracket & Amber Light Locate to the far end of the frame.

  • Page 48: 15' Bedded Unit

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Overhead Layouts NOTE: Center All Reflectors Vertically On Tube 15' BEDDED UNIT 2-32...

  • Page 49: Wiring Harness

    — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Wiring Harness When installing the harnesses, do not cut or break the wire coverings. Tie harnesses away from moving parts, such as cylinders and folding links. The wiring harnesses consist of four pieces;...
  • Page 50 — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Wiring Harness FIG. 3-17 2-34...
  • Page 51 — Set Up FIELD CULTIVATORS Transport Marking & Light Kits — Wiring Harness RIGID 12' Main Wiring MAIN FRAME Harness SHOWN Cross Wiring Extension Extension Harness Harness Harness FOLDING 12' Main Wiring MAIN FRAME Harness SHOWN Cross Wiring Extension Extension Harness Harness Harness...

  • Page 52: Checking Function

    FIELD CULTIVATORS Checking Function To check for proper functioning of the Unverferth Transport Marking Kit, perform the following: 1. Turn on the tractor’s flashing lights. The amber extremity lights on the Perfecta cultivator should flash in unison with the tractor lights.

  • Page 53: Extensions (Optional)

    — Set Up FIELD CULTIVATORS Extensions (82745G or 82745R) (Optional) NOTE: On machine with optional extensions, refer to the following instructions for assembly. 1. Attach 6" long and 9" long extensions to the second and third tool bar as shown. Secure using two 1/2"...

  • Page 54: Bedded Crop Perfecta - On 60" Row Spacing Assembly

    — Set Up FIELD CULTIVATORS Bedded Crop Perfecta Models — On 60” Row Spacing Assembly On 5 bed x 60” Bedded Models, a spacer (87053B) must be installed on the bedding shanks on the main frame to avoid interference with the folding cylinders. 1.

  • Page 55: Bedded Crop Perfecta - On 60" Row Spacing Assembly

    — Set Up FIELD CULTIVATORS Bedded Crop Perfecta Models (continued) — On 60” Row Spacing Assembly 4. Basket mounting frames (87051B) must be installed for outer rolling baskets on the main frame (Fig. 2-28). Position mounting frames as shown on layout and secure with U-bolts (91434) and locknuts (9800).

  • Page 56: Overhead Layouts

    — Set Up FIELD CULTIVATORS Overhead Layout Use these "Overhead Layout" drawings (on the following pages) as an assembly guide for the positioning of components onto the cultivator frame. NOTE: All dimensions are in inches - unless otherwise specified. Model 10 Model 12 4”...
  • Page 57 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 10 Ft. Base - Single Basket 41 1/4 2-41...
  • Page 58 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 10 Ft. Base - Double Basket 41 1/4 2-42...
  • Page 59 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 10 Ft. Base - Single Drum Roller 41 1/4 2-43...
  • Page 60 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 12 Ft. Base - Single Basket 2-44...
  • Page 61 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 12 Ft. Base - Double Basket 2-45...
  • Page 62 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 12 Ft. Base - Single Drum Roller 2-46...
  • Page 63 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 13 Ft. Base - Single Basket 2-47...
  • Page 64 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 13 Ft. Base - Double Basket 2-48...
  • Page 65 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 13 Ft. Base - Single Drum Roller 2-49...
  • Page 66 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 14 Ft. Base - Single Basket 2-50...
  • Page 67 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 14 Ft. Base - Double Basket 2-51...
  • Page 68 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 14 Ft. Base - Single Drum Roller 2-52...
  • Page 69 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 15 Ft. Base - Single Basket 2-53...
  • Page 70 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 15 Ft. Base - Double Basket 2-54...
  • Page 71 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 15 Ft. Base - Single Drum Roller 2-55...
  • Page 72 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 2-56...
  • Page 73 — Set Up FIELD CULTIVATORS Overhead Layout — Rigid Perfecta Models 2-57...
  • Page 74 Space Approx. — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 9 FT. BASE WITH 4 1/2 FT. WINGS - SINGLE BASKET Space Approx. 2-58...
  • Page 75 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-59...
  • Page 76 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-60...
  • Page 77 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-61...
  • Page 78 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-62...
  • Page 79 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-63...
  • Page 80 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-64...
  • Page 81 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-65...
  • Page 82 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-66...
  • Page 83 — Set Up FIELD CULTIVATORS Overhead Layout — Folding Perfecta Models 2-67...
  • Page 84 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 7 FT. BASE WITH SHANKS ON 80" ROW SPACINGS 2-68...
  • Page 85 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 12 FT. BASE WITH SHANKS ON 36" ROW SPACINGS 2-69...
  • Page 86 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 15 FT. BASE WITH SHANKS ON 30" ROW SPACINGS 2-70...
  • Page 87 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 15 FT. BASE WITH SHANKS ON 38" ROW SPACINGS 5 TYP 8 3/4 TYP 20 TYP 18 TYP 10 TYP  2-71...
  • Page 88 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 15 FT. BASE WITH SHANKS ON 39" ROW SPACINGS 5 TYP 21 TYP 18 TYP 8 3/4 TYP 11 TYP FINISH: WEIGHT ASSEMBLE IMPLEMENT GREEN REV LEVEL LATEST CN CN7450 CRIMSON RED REVISION DATE...
  • Page 89 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 15 FT. BASE WITH SHANKS ON 40" ROW SPACINGS 5 TYP 22 TYP 18 TYP 8 3/4 TYP 12 TYP FINISH: WEIGHT ASSEMBLE REV LEVEL IMPLEMENT GREEN LATE CRIMSON RED REVISION DATE 3/18/2019 - 10:51...
  • Page 90 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-74...
  • Page 91 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-75...
  • Page 92 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-76...
  • Page 93 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-77...
  • Page 94 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-78...
  • Page 95 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-79...
  • Page 96 — Set Up FIELD CULTIVATORS Overhead Layout — Bedded Crop Perfecta Models 2-80...
  • Page 97 — Operation FIELD CULTIVATORS SECTION III Operation General Operation Information ....................3-2 Preparing Tractor ........................3-2 Front-End Weights ....................... 3-2 Sway Blocks ........................3-2 Wheel Spacing ........................3-2 Tractor Quick Hitch ......................3-3 Tractor 3-Point Top Link Arm ..................... 3-3 Drawbar Position .........................

  • Page 98: General Operation Information

    — Operation FIELD CULTIVATORS General Operation Information READ AND UNDERSTAND SAFETY RULES BEFORE OPERATING OR SERVICING THIS • MACHINE. REVIEW "SAFETY" SECTION IN THIS MANUAL IF NECESSARY. Read this operation section thoroughly. Acquaint yourself with the adjustments required to obtain efficient and trouble-free operations. Preparing Tractor Before operating implement refer to tractor operator’s manual for information concerning safe methods of operation, hydraulics, hitch adjustment, tire inflation, wheel adjustments, and...

  • Page 99: Tractor Quick Hitch

    — Operation FIELD CULTIVATORS Preparing Tractor (continued) Tractor Quick Hitch Recommended for convenient connection to tractor, also increases clearance between tractor and Perfecta in transport. Tractor 3-Point Top Link Arm Connect to the top hole on the tractor to allow the Perfecta to raise vertically. Using the bottom hole on the tractor causes the Perfecta to tip in toward the tractor as it raises, reducing clearance during transport.

  • Page 100: Preparing Field Cultivator

    — Operation FIELD CULTIVATORS Preparing Field Cultivator Mast And Hitch • Before connecting tractor to the implement, be sure the mast and hitch pins are assembled correctly. See SETUP section “Mast Assembly” for illustration and instructions on assembly. Perfecta Size & Style Tractor Hitch Type That The Perfecta Will Accept CAT.

  • Page 101: Tire Pressure

    — Operation FIELD CULTIVATORS Preparing Field Cultivator (continued) Tire Pressure Check tire pressure, see “MAINTENANCE” section for recommended air pressure. Be sure tire pressure is equal in all tires. IMPROPERLY TORQUED WHEEL NUTS/BOLTS CAN CAUSE A LOSS OF IMPLEMENT • CONTROL AND MACHINE DAMAGE.

  • Page 102: Attaching Field Cultivator To Tractor

    Lock the jaw latches into place. On the RIGID PERFECTA and BEDDED CROP PERFECTA 10’-20’ sizes, bushings (83881) are required on the lower hitch pins if being used with CAT 3 or CAT 3-N Quick-Hitch.

  • Page 103: Unfolding The Wings

    — Operation FIELD CULTIVATORS Unfolding The Wings KEEP CLEAR OF POWER LINES WHEN FOLDING/UNFOLDING WINGS. WINGS MAY • BECOME TALLER THAN SOME POWER LINES DURING THE FOLD CYCLE CAUSING ELECTROCUTION AND SERIOUS INJURY OR DEATH. MOVING WINGS CAN CAUSE SERIOUS INJURY OR DEATH. KEEP AWAY FROM FOLD- •...

  • Page 104: Leveling Cultivator Frame

    — Operation FIELD CULTIVATORS Leveling Cultivator Frame For best results when leveling your PERFECTA, position the tractor with the cultivator on a level floor. Check the tractor tire pressure and inflate equally from side-to-side. See your tractor operator’s manual for correct tire inflation pressure. Side-To-Side Leveling With the PERFECTA attached to the tractor, raise the cultivator a couple of inches off the floor.

  • Page 105: Transporting

    See federal regulation 49 CFR 562; available at www.govinfo.gov for US federal law requirements. See your Unverferth dealer for additional brackets, reflectors, or lights to meet your requirements. For safe transporting of these implements, the transport speed should never exceed 10 M.P.H.

  • Page 106: Unhitching

    — Operation FIELD CULTIVATORS Unhitching ALWAYS RELIEVE HYDRAULIC SYSTEM PRESSURE BEFORE DISCONNECTING HOSES • FROM TRACTOR OR SERVICING HYDRAULIC SYSTEM. SEE TRACTOR OPERATOR’S MANUAL FOR PROPER PROCEDURES. Lower the PERFECTA on a flat surface clear of any debris or obstruction. Unhitch the unit, disconnect the hydraulic hoses (FOLDING PERFECTA ONLY) and install dust covers over the hose plugs and outlets.

  • Page 107: Folding Perfecta

    — Operation FIELD CULTIVATORS Field Adjustments (continued) Folding Perfecta Singles 20.5 x 8 -10-- Standard on 4’, 5’, and 6’ wings. Duals 20.5 x 8-10 -- Standard on 7’ and 8’ wings. Bedded Crop Perfecta Singles 16.5 x 6.5-8 -- Standard on all sizes. The weight of the PERFECTA should be carried on the 3-PT.

  • Page 108: Rolling Harrow - Single Basket

    — Operation FIELD CULTIVATORS Field Adjustments (continued) Rolling Harrow - Single Basket The Rolling Harrow basket is designed to help provide an excellent seedbed when used in conjunction with the S-tines and one-bar drag tooth harrow. A maximum amount of leveling and conditioning of the soil is obtained when the roller is operated in the aggressive position (FIG.

  • Page 109: Rolling Harrow - Double Basket

    — Operation FIELD CULTIVATORS Field Adjustments (continued) Rolling Harrow - Double Basket Normal Position In most cases, the unit runs with the aggressive basket positioned to the front (FIG. 3-7) for maximum penetration in normal soil conditions. A maximum amount of leveling and conditioning of the soil is obtained when the aggressive basket is positioned to the front (as shown in FIG.
  • Page 110 — Operation FIELD CULTIVATORS Field Adjustments (continued) Alternate Position A maximum amount of firming and conditioning of the soil is obtained when the aggressive basket is positioned at the rear (as shown in FIG. 3-8). To reverse Rolling Harrow baskets, remove mounting pin (9500423) and spiral pin (91144-186) (FIG.

  • Page 111: Working Depth

    — Operation FIELD CULTIVATORS Field Adjustments (continued) Working Depth Position “X” - setting for normal S-tine working depth of 2-4 inches. Position "X" Position “Y” - setting for deeper S-tine working Position "Y" depth of 4-6 inches. Additional adjustment is provided (Position “Y” FIG.

  • Page 112: Spike Bar Adjustment

    — Operation FIELD CULTIVATORS Field Adjustments (continued) Spike Bar Adjustment FIG. 3-11 The spike tooth leveler bar can be mounted in any of the 3 holes of the hanger. Set the spike bar lower for more leveling action. The bar should be set to the same height on both hangers of each leveler bar section of the machine.
  • Page 113 — Operation FIELD CULTIVATORS Field Adjustments (continued) Bedded crop rear shank has adjustable foot FIG. 3-12 which is adjustable from 25 to 55 and may be adjusted by tightening or loosening set screw once angle/position is set, tighten both lower bolts.
  • Page 114 — Operation FIELD CULTIVATORS Field Adjustments (continued) POSITION "B" (FIG. 3-14) R.H. View Position "B" will allow the wing to remain level to the base. This setting should be used for turning in raised position, when fields are level and a rigid unit is desired. FIG.

  • Page 115: Single Basket Reinforcement Disc Plate Part #87229 (Optional)

    — Operation FIELD CULTIVATORS Single Basket Reinforcement Disc Plate Part #87229 (Optional) This option is for reinforcing both the regular and aggressive basket in rocky soils. This accessory will provide additional stiffness to your basket. • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING THE IMPLEMENT.
  • Page 116 FIG. 3-36 This option is for reinforcing both the regular Secure discs into place by tack welding. — Operation FIELD CULTIVATORS and aggressive basket in rocky soils. This ac- Weld where discs and basket blades are cessory will provide additional stiffness to your in contact (Fig.

  • Page 117: Double Basket Weld-In Reinforcement Disc Part #74964 (Optional)

    — Operation FIELD CULTIVATORS Double Basket Weld-In Reinforcement Disc Part #74964 (Optional) This option is for reinforcing both the regular and aggressive basket in rocky soils. This accessory will provide additional stiffness to your basket. • TIPPING OR MOVEMENT OF THE MACHINE CAN CAUSE SERIOUS INJURY OR DEATH.
  • Page 118 — Operation FIELD CULTIVATORS Double Basket Weld-In Reinforcement Disc Part #74964 (Optional) 3. Remove powder coating before welding. Secure discs into place by tack welding. Weld Aggressive Basket where discs and basket blades are in contact (FIG. 2-21 & 2-22). Weld Disc FIG.
  • Page 119 — Maintenance FIELD CULTIVATORS SECTION IV Maintenance Storage ............................4-2 Lubrication ..........................4-2 Wheel Bearings ........................4-2 Wing Assembly ........................4-2 Hub Assembly ..........................4-2 Replacing Single Rolling Harrow Basket Bearings ..............4-3 Replacing Double Rolling Harrow Basket Bearings ..............4-4 Installing Retaining Rings ......................

  • Page 120: Storage

    — Maintenance FIELD CULTIVATORS Storage Your implement is an important investment. Spend a little time to protect it from destructive rust and corrosion. You will be repaid in longer service life and better performance. Do the following before placing the implement in storage: 1.

  • Page 121: Replacing Single Rolling Harrow Basket Bearings

    Tighten 5/16”-18UNC capscrews before you tighten the setscrew in the lock collar. Turn lock collar in the direction of travel. Tighten capscrews according to “Torque Chart”. All ROLLING HARROW® bearings are manufactured with triple-lip seals. It is important to use Unverferth bearings (87181) for maximum life.

  • Page 122: Replacing Double Rolling Harrow Basket Bearings

    — Maintenance FIELD CULTIVATORS Replacing Double Rolling Harrow Basket Bearings • EYE PROTECTION AND OTHER APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT MUST BE WORN WHILE SERVICING THIS IMPLEMENT. 1. Bearing replacement kit (74006) is available for the ROLLING HARROW. 2. Park unit on a firm level surface. Unfold wings, lower the PERFECTA to the ground, set the tractor parking brake, depressurize the hydraulic system, shut off the engine, and...
  • Page 123 — Maintenance FIELD CULTIVATORS Replacing Double Rolling Harrow Basket Bearings (continued) 11. Push the basket back into the frame. Align the hole in the bearing bolt with the hole in the frame side plate. Thread the new 5/8”-11UNC x 1 1/4” capscrew (900872) into the bearing bolt (74280) until the epoxy begins to engage.

  • Page 124: Installing Retaining Rings

    — Maintenance FIELD CULTIVATORS Installing Retaining Rings 1. USE PROPER TOOLS for assembling rings onto pins (for plain external retaining rings use a flat-blade retaining ring pliers). 2. Before inserting pins, be sure the GROOVE IS FREE FROM ALL FOREIGN MATERIAL (paint, dirt, etc.), to ensure a proper seating.

  • Page 125: Hydraulic System

    — Maintenance FIELD CULTIVATORS Hydraulic System MODELS WITH WINGS ONLY NOTE: For plumbing diagram - refer to "Hydraulic Diagram". Refer to PARTS Section for hydraulic components detailed listing. HYDRAULIC DIAGRAM FIG. 4-5 OM-00379 ITEM DESCRIPTION COMMENTS Wing Fold Cylinder Standard on ALL units with wings Orifices Standard on ALL units with wings...

  • Page 126: Troubleshooting

    — Maintenance FIELD CULTIVATORS Troubleshooting PROBABLE CAUSE CORRECTION Hydraulics Not Functioning Properly Refer to Tractor Operator’s Manual for valve and Incorrect hose hook-up to tractor control levers control lever arrangement Insufficient tractor hydraulic pressure Check hydraulic reservoir oil level Refer to tractor “Operator’s Manual” or hydraulic system recommendations Find cause and correct, see MAINTENANCE sec- Hydraulic components leaking oil...
  • Page 127 — Maintenance FIELD CULTIVATORS Complete Torque Chart – Capscrews - Grade 5 NOTE: Grade 5 capscrews can be identified by three radial dashes on head. NOTE: For wheel torque requirements, refer to Wheels and Tires. NOTE: Tighten U-bolts to have the same number of threads exposed on each end. FOOT NEWTON FOOT...

  • Page 128: Wheels And Tires

    — Maintenance FIELD CULTIVATORS Wheels and Tires Wheel Nut Torque IMPROPERLY TORQUED WHEEL NUTS/BOLTS CAN CAUSE A LOSS OF IMPLEMENT • CONTROL AND MA CHINE DAMAGE. TORQUE WHEEL NUTS/BOLTS TO VALUES IN TABLE. CHECK TORQUE BEFORE INITIAL USE, AFTER ONE HOUR OF USE, AND EACH HOUR UNTIL WHEEL NUTS/BOLTS MAINTAIN TORQUE VALUE.

  • Page 129: Tire Warranty

    — Maintenance FIELD CULTIVATORS Wheels and Tires Tire Warranty For questions regarding new tire warranty, please contact your local original equipment tire dealer. Used tires carry no warranty. Following are phone numbers and Websites for your convenience: Carlisle www.carlisletire.com Phone 800-260-7959 Fax 800-352-0075 Greenball www.greenball.com...
  • Page 130 — Maintenance FIELD CULTIVATORS Notes 4-12...
  • Page 131 — Parts FIELD CULTIVATORS SECTION V Parts Mast Components with Square Truss Tubes ................5-2 Mast Components with Round Truss Tubes ................5-4 Main Frame – Rigid Perfecta ....................5-6 Main Frame – Folding Perfecta ....................5-8 Main Frame – Bedded Crop Perfecta ..................5-10 Wing Components ........................

  • Page 132: Mast Components With Square Truss Tubes

    — Parts FIELD CULTIVATORS Mast Components with Square Truss Tubes Please visit www.unverferth.com/parts/ for the most current parts listing.
  • Page 133 — Parts FIELD CULTIVATORS Mast Components with Square Truss Tubes Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 3-Point Bolt-On Heavy Mast Asy 74862B W/Cast Clamps 62640 Spacer/Bushing 2” Long 87290 Pin Weldment 1” Dia. x 4 9/16”...

  • Page 134: Mast Components With Round Truss Tubes

    — Parts FIELD CULTIVATORS Mast Components with Round Truss Tubes Please visit www.unverferth.com/parts/ for the most current parts listing. 9' - used on 18'/20'/22'/24'/26' Folding 12' - used on 20’/22’/ 24'/26'/28' Folding Perfecta Models ONLY...
  • Page 135 — Parts FIELD CULTIVATORS Mast Components with Round Truss Tubes Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 86293 Mast Assembly Complete 62640 Tube/Spacer 2" Long 83552B Mast Weldment 83557B Plate 86292B Brace (round pipe)

  • Page 136: Main Frame - Rigid Perfecta

    — Parts FIELD CULTIVATORS Main Frame — Rigid Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing.
  • Page 137 — Parts FIELD CULTIVATORS Main Frame — Rigid Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 87684R Main Frame w/Decals (7 Ft.) =Red= 88697G Main Frame w/Decals (10 Ft.) =Green= 88697R Main Frame w/Decals (10 Ft.) =Red= 88697NG Main Frame w/Decals (10 Ft.) =Orange=...

  • Page 138: Main Frame - Folding Perfecta

    — Parts FIELD CULTIVATORS Main Frame — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. Serial No. A49340099 & Lower Serial No. A49340100 & Higher OM00329...
  • Page 139 — Parts FIELD CULTIVATORS Main Frame — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 88702G Main Frame (12 Ft.) w/Decals =Green= Serial # A61570100 and Higher 88702R Main Frame (12 Ft.) w/Decals =Red= 88701G Main Frame (9 Ft.) w/Decals =Green=...

  • Page 140: Main Frame - Bedded Crop Perfecta

    — Parts FIELD CULTIVATORS Main Frame — Bedded Crop Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. 5-10...
  • Page 141 — Parts FIELD CULTIVATORS Main Frame — Bedded Crop Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 88703G Main Frame 15’ Weldment (Green) w/Decals For 3-60” Beds Rigid Frame For 6-30” Beds Rigid Frame 88703R Main Frame 15’...

  • Page 142: Wing Components

    — Parts FIELD CULTIVATORS Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. (7 FT. L.H. WING SHOWN) 5-12...
  • Page 143 — Parts FIELD CULTIVATORS Wing Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9800 Top Locknut 1/2-13UNC 82741G Extension Tube Weldment 6” Long =Green= 82741R Extension Tube Weldment 6” Long =Red= 91120 U-Bolt 1/2-13UNC x 3 88687G R.H.

  • Page 144: Hydraulics - Folding Perfecta

    — Parts FIELD CULTIVATORS Hydraulics — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. View "A" OM-00335 5-14...
  • Page 145 — Parts FIELD CULTIVATORS Hydraulics — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. 9' BASE 12' BASE ITEM PART NO. DESCRIPTION 4' & 5' 6', 7' & 8' 4' & 5' 6', 7' & 8' WINGS...

  • Page 146: Single Rolling Harrow Basket & Mounting Arm Components

    — Parts FIELD CULTIVATORS Single Rolling Harrow Basket & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. DETAIL A 7 7/16 REF 5-16...
  • Page 147 — Parts FIELD CULTIVATORS Single Rolling Harrow Basket & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 87181 Flange Bearing Assembly Incl. washer, flange bearing, seal & collar 9404-019 5/16 Lock Washer 97321 Capscrew 5/16-18 x 7/8"...

  • Page 148: Double Rolling Harrow Basket & Mounting Arm Components

    — Parts FIELD CULTIVATORS Double Rolling Harrow Basket & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM 7479 9390 9928 8625 8925 8132 7484 9717 9405 7485 7547 7640 2149 7633 9024 9093 9501 9516...
  • Page 149 — Parts FIELD CULTIVATORS Double Rolling Harrow Basket & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 74793B Bent Arm Weldment 9390-068 Capscrew 3/8”-16UNC x 4 1/2” G5 9928 Lock Nut/Top 3/8”-16UNC 86251B Pin Weldment 5/8”...

  • Page 150: Single Drum Roller & Mounting Arm Components

    — Parts FIELD CULTIVATORS Single Drum Roller & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM 7642 8562 9801 7642 7643 9390 9928 7642 6717 8225 9717 8625 8132 8925 7484 7633 9093 9024 6792...
  • Page 151 — Parts FIELD CULTIVATORS Single Drum Roller & Mounting Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. QTY PER DRUM ROLLER ASSEMBLY PART ITEM DESCRIPTION NUMBER 3 FT. 4 FT. 5 FT. 6 FT. LH 6 FT. RH 78832B Drum Roller 3 Ft.

  • Page 152: Leveler Bar Components

    — Parts FIELD CULTIVATORS Leveler Bar Components Please visit www.unverferth.com/parts/ for the most current parts listing. SPIKED TOOTH DIAGONAL TOOTH 5-22...
  • Page 153 — Parts FIELD CULTIVATORS Leveler Bar Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NUMBER DESCRIPTION NOTES 74676B Diagonal Bent Left-Hand Tooth 74672B Diagonal Bent Right-Hand Tooth 74671B Diagonal Bent Left-Hand “Y” Tooth 74670B Diagonal Bent Right-Hand “Y” Tooth 91069PL Flat Washer 2"...

  • Page 154: Leveler Bar Assemblies

    — Parts FIELD CULTIVATORS Leveler Bar Assemblies Please visit www.unverferth.com/parts/ for the most current parts listing. 5-24...
  • Page 155 — Parts FIELD CULTIVATORS Leveler Bar Assemblies Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION 71299 Straight Spike-Tooth One Bar 2’ Assembly 71181 Straight Spike-Tooth One Bar 3’ Assembly 71182 Straight Spike-Tooth One Bar 4’ Assembly 106919 Straight Spike-Tooth One Bar 4 1/2’...

  • Page 156: S-Tines, Sweeps, & Shovels - Model 10

    — Parts FIELD CULTIVATORS S-Tines, Sweeps & Shovels — Model 10 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 82065 Clamp 9952 S-Tine 1 1/4 x 1/2 (32 x 12 M.M.) 9823 Plow Bolt 3/8-16UNC x 1 1/2" Lg.

  • Page 157: S-Tines, Sweeps, & Shovels - Model 12

    — Parts FIELD CULTIVATORS S-Tines, Sweeps & Shovels — Model 12 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 83417 Clamp 9405-082 Flat Washer 7/16" USS 91411 Plow Bolt 7/16-14UNC x 1 1/2" #3 Flat Head...

  • Page 158: S-Tines, Sweeps, & Shovels - Model 14

    — Parts FIELD CULTIVATORS S-Tines, Sweeps & Shovels — Model 14 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9405-082 Flat Washer 7/16" USS 93687 Sweep 7” 91411 Plow Bolt 7/16-14UNC x 1 1/2" #3 Flat Head...

  • Page 159: S-Tines - Bedded Crop Perfecta

    — Parts FIELD CULTIVATORS S-Tines — Bedded Crop Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 82065 Clamp 91381 Sweep 1/4 x 2 3/4 9390-112 Capscrew 1/2-13 x 4 1/2" Lg. 9800 Locknut 1/2-13 9952 S-Tine .472x1.25x18 7/32...
  • Page 160 — Parts FIELD CULTIVATORS S-Tine Heavy-Duty Assembly — Bedded Crop Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 75955B Plate 9002071B Shank 9002116B K-Flex Bracket 91411 Plow Bolt 7/16-14UNC x 1 1/2 Gr.5...

  • Page 161: Shank Assembly - Bedded Crop Perfecta

    — Parts FIELD CULTIVATORS Shank Assembly - Bedded Crop Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 83587 Shank Assembly 83580 Clamp Bracket 83581 Shank 83582 Foot 83586 Clamp Plate 91596 Capscrew 1/2-13UNC x 2 1/2" Lg. (Full Thread) 9390-126 Capscrew 5/8-11UNC x 2 1/2"...

  • Page 162: Dual Gauge Wheel - Prior To Serial #A59820100

    — Parts FIELD CULTIVATORS Dual Gauge Wheel — Prior to Serial #A59820100 Please visit www.unverferth.com/parts/ for the most current parts listing. OM-00382 5-32...
  • Page 163 — Parts FIELD CULTIVATORS Dual Gauge Wheel — Prior to Serial #A59820100 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 92519 Hub Assembly 91049 Bevel Nut 91052 Hub Stud Bolt 1/2-20UNF x 1.219 For Welded Hub 9347 Hub Stud Bolt 1/2-20UNF x 1.875 For Cast Hub...

  • Page 164: Dual Gauge Wheel - Beginning With Serial #A59820100

    — Parts FIELD CULTIVATORS Dual Gauge Wheel — Beginning with Serial #A59820100 Please visit www.unverferth.com/parts/ for the most current parts listing. 5-34...
  • Page 165 — Parts FIELD CULTIVATORS Dual Gauge Wheel — Beginning with Serial #A59820100 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Includes Items 2 73956B Gauge Wheel Assembly through 27 Includes Items 3 73957B Mounting Arm/Spindle/Hub Assembly...

  • Page 166: Single Gauge Wheel #83824

    — Parts FIELD CULTIVATORS Single Gauge Wheel #83824 Please visit www.unverferth.com/parts/ for the most current parts listing. OM-01431 5-36...
  • Page 167 — Parts FIELD CULTIVATORS Single Gauge Wheel #83824 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 92519 Hub Assembly 91049 Bevel Nut 91052 Hub Stud Bolt 1/2-20UNF x 1.219 For Welded Hub 9347 Hub Stud Bolt 1/2-20UNF x 1.875 For Cast Hub...

  • Page 168: Single Gauge Wheel #74606B

    — Parts FIELD CULTIVATORS Single Gauge Wheel #74606B Please visit www.unverferth.com/parts/ for the most current parts listing. 5-38...
  • Page 169 — Parts FIELD CULTIVATORS Single Gauge Wheel #74606B Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES Includes Items 2 74606B Gauge Wheel Assembly through 27 Includes Items 3 74607B Mounting Arm/Spindle/Hub Assembly through 21...
  • Page 170 — Parts FIELD CULTIVATORS Light Kit #86763B — Rigid Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. 5-40...
  • Page 171 — Parts FIELD CULTIVATORS Light Kit #86763B — Rigid Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES QTY. 22790 Wiring Harness 64132 Wiring Harness 72" 77803B Light Bracket Guard 77805B Light Bracket Assembly...
  • Page 172 — Parts FIELD CULTIVATORS Light Kit #86764B — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. 5-42...
  • Page 173 — Parts FIELD CULTIVATORS Light Kit #86764B — Folding Perfecta Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES QTY. 22790 Wiring Harness 64140 Wiring Harness 96" 78920B Light Bracket Guard 86466 Wiring Harness 86769B...

  • Page 174: 12" Extension Bundle Components (Optional)

    — Parts FIELD CULTIVATORS 12” Extension Bundle Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 82741G Tube Weldment 6" =Green= 82741R Tube Weldment 6" =Red= 82742G Tube Weldment 9" =Green= 82742R Tube Weldment 9" =Red= 82743G Tube Weldment 12"...

  • Page 175: 16" Extension Bundle Components (Optional)

    — Parts FIELD CULTIVATORS 16” Extension Bundle Components (Optional) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 82885G Tube Weldment 16" LH =Green= 82885R Tube Weldment 16" LH =Red= 82886G Tube Weldment 16" RH (Shown) =Green= 82886R Tube Weldment 16"...
  • Page 176 L:\MANUALS\PERFECTA\\74279.indd//July 2016-9//November 2016-10//May 2017-11/July 2017-12//November 2017-13//September 2018-14//March 2019-15//August 2019-16//OCTOBER 2020-17//August 2021-18//December 2021-19...

This manual is also suitable for:

Perfecta 12Perfecta 14

Table of Contents