Special Functions; Special Functions Special Functions 17; Clock Programming; Grease Lter Saturation Alarm - Electrolux RH30WC60GS Installation, Use & Care Manual

Special functions

Clock pr

Clock programming

Clock pr ogramming ogramming ogramming
Clock pr Clock pr ogramming
The clock can be reprogrammed at any time except during an active timed function.
The clock can be displayed in a twelve hour format and valid clock times are from 1:00 to 12:59.
The clock can be reprogrammed pressing the "T T T T T imer
adjusted with the " " and "
The user can have minute increments / decrements of 1 minute, but if the user keep pressing the "
" " buttons for more than 1 second, the increments / decrements will be of 5 minutes.
During this option the control will round to the nearest 5 minutes.
The user can nish on reprogramming the clock pressing the " T T T T T imer
After 1 minute of no button pressed the control will accept the programmed clock time and will add one
minute to the set clock.
Gr Gr Gr Gr Grease lter saturation alarm ease lter saturation alarm ease lter saturation alarm ease lter saturation alarm ease lter saturation alarm
After thirty fan functional hours, the display will show " Gr Gr Gr Gr Grease Filter
When this icon is shown in the display, the grease lters installed are required to be washed.
To reset the grease lter saturation alarm the user must press the "
action the icon " Gr Gr Gr Gr Grease lter ease lter ease lter" is not displayed, and the hood has the normal display operation. ease lter
ease lter
Char Char coal lter saturation alarm (Recir coal lter saturation alarm (Recir
Char Charcoal lter saturation alarm (Recir Char coal lter saturation alarm (Recir coal lter saturation alarm (Recirculating accessories)
After one hundred and twenty functional hours of the fan, the display will show " Char
is active. When this icon ashes on display, the charcoal lters installed are required to be replaced or
reactivated.
To reset the charcoal lter saturation indication the user must press the "
Char Char
this time the icon " Char Char Char coal lter

Audible signal activation and deactivation

Audible signal activation and deactivation Audible signal activation and deactivation
Audible signal activation and deactivation Audible signal activation and deactivation
The audible signals can be activated or deactivated pressing the "Light
If the audible signal is activated, a tone must sound and the " Snd
2 seconds.
If the audible signal is deactivated, the " Snd
tone must sound.
Char Charcoal lter inclusion and exclusion (Recir Char coal lter inclusion and exclusion (Recir coal lter inclusion and exclusion (Recirculating accessories) coal lter inclusion and exclusion (Recir
Char Char coal lter inclusion and exclusion (Recir
The charcoal lter inclusion or exclusion can be set by pressing the "
time for 5 seconds.
The Inclusion or exclusion of charcoal lter must be selected while the lamps and the motor are OFF .
When the charcoal lter has been excluded, the charcoal lter alarm is disabled.

Heat sensor

Heat sensor
Heat sensor Heat sensor Heat sensor
The control is equipped with a heat sensor that will turn on the blower at second speed if excessive heat
158° F 158° F 70°C 70°C
occurs (over 158° F 158° F or 70°C 158° F 70°C) surrounding the control area. 70°C
If the blower is OFF or if it is operating at rst speed, the blower will be set automatically to second speed,
the display shows the word " CArE
During this state, the user may raise the blower speed to third speed but can not decrease the speed.
When the temperature level on the hood drops to normal, the blower will operate in the setting de ned by
the user before the alarm occured.
Control buttons - Special functions
imer imer imer imer" button for 5 seconds, and after, the clock can be
" buttons. Colon ":" will ash indicating clock programming mode.
culating accessories) culating accessories)
culating accessories) culating accessories)
coal lter coal lter
coal lter coal lter" is not displayed and the hood has the normal display operation.
Snd Snd Snd" symbol must appear on the display for 2 seconds and no Snd
culating accessories) culating accessories) culating accessories)
culating accessories)
CArE CArE CArE" to indicate that heat sensor has detected an excessive heat.
CArE
imer imer
imer" button. imer
ease Filter ease Filter
ease Filter ease Filter" if the fan is active.
" button for 5 seconds, after this
Char Char Char coal Filter
Char
" button for 5 seconds, after
Light" button for 5 seconds. Light Light Light
Snd Snd Snd" symbol must appear on the display for
Snd
" and " " buttons at the same
"/
coal Filter coal Filter" if the fan coal Filter
coal Filter
17 17 17 17
17