Geutebruck G-ST 8000+/2U Instructions For Use

Advertisement

Quick Links

Instructions for Use G-ST 8000+/2U

General Safety Instructions

Commissioning

The device may only be commissioned by qualified
personnel who are familiar with the device and the
technology.
Make sure that all applicable safety requirements are
fulfilled.
WARNING
Electrical voltages!
Personal and property damage
All connection work should only be performed
on the device when it is switched off.
Do not remove the housing cover.
For the connection of control lines, please refer to the
instructions in the user manual.
Use a socket with a protective contact to connect the
power-supply unit.
Ensure a power supply of 110 VAC to 230 VAC. When
connecting external contacts, do not apply voltages
above 3.3 V, this may cause damage.
The operating system is precisely preconfigured for your
device.

Operation

When operating the device, the local applicable laws,
other regulations, standards, and rules of technology
must be observed. In the interest of a safe work
process, operating company and supervisors are
responsible for their compliance.
During all work, check the device for any damage. All
parts must be correctly mounted and fulfill all conditions
to ensure proper operation.
WARNING
Electrical voltages!
Personal and property damage
Do not use the device if it is damaged.
Disconnect the device from the power supply.
Do not use the supply cable for purposes for which it is
not intended. Protect the cable from heat, oil, and sharp
edges.
In dangerous situations or in case of malfunctions,
disconnect the device from the power supply immediately.
Password disclosure:
dialog box, enter the following:
User name:
Administrator
Pass word:
Pa$$w0rd
Then assign your own new password and write it down!
The password must be at least six characters long.
The password must contain characters from three of the
following categories:
Upper case letters (A to Z)
Lowercase letters (a through z)
Numbers in base 10 (0 to 9)
Non-alphabetic characters (for example !, $, #, %)
Please note that this is the Windows system
password, it is not possible to recover the password if
it is lost! The user profile Administrator allows full
access to your G-ST.
Confirm with the "ENTER" key.

Repair and Maintenance

Ensure that the device is repaired professionally. Mark
the defect clearly and disconnect the power plug so that
no accidents or damage can occur due to a defective
device or be caused by it until the device is repaired.
Do not remove the housing cover! There are only
maintenance-free components inside the device.
WARNING
Electrical voltages!
Personal and property damage
Disconnect the device from the power supply
during all repair and maintenance work.
Work on the electrical equipment may only be
performed by a qualified electrician.
CAUTION
Danger due to the use of non-original parts!
Personal and property damage
Only use original spare parts.
WARNING
Explosion hazard!
If the mainboard battery is replaced by an unsuitable
battery type, explosions may occur.
Make sure that a suitable battery type is used.
Dispose the battery according to the valid legal
requirements and local regulations.

Front View (Without Cover)

No. Element
1
Front panel with controls
and signal indicators.
1.
USB 3.0 ports
2.
Power key
3.
Reset key
4.
Operation indicator LED
5.
SATA LED
6.
Network LEDS
7.
UID LED
8.
Power- supply unit LED
9.
Power-supply unit error LED
10.
Alarm Reset key
11.
Fan error LED
12.
Fan Error Reset key
2
HDD plug-in with HDD slot 0-7.
Rear View
No. Element
1
Redundant power-supply units.
2
Port for PS/2 keyboard (6-pin mini-DIN socket).
3
Port for PS/2 mouse (6-pin mini-DIN socket).
4
USB 2.0 ports.
5
Display Port outputs for connecting a PC monitor.
6
Serial RS-232 interface (9-pin Sub-D connector).
7
DVI-D graphics output for connecting a PC monitor.
8
Network ports (Ethernet 10 /100 / 1000 Base/T - RJ45).
9
USB 3.0 ports.
10 Sound card ports.
11 10/100 Mbps RJ45 port for remote control of the RAID controller.
12 Control inputs for connecting external contacts for event-controlled image recording / relay outputs.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the G-ST 8000+/2U and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Geutebruck G-ST 8000+/2U

  • Page 1 Instructions for Use G-ST 8000+/2U Front View (Without Cover) General Safety Instructions Password disclosure: dialog box, enter the following: Commissioning  User name: Administrator  The device may only be commissioned by qualified Pass word: Pa$$w0rd personnel who are familiar with the device and the Then assign your own new password and write it down! technology.
  • Page 2 Intended Use with a special cushion packing. If possible, always use the original packaging. The G-ST 8000+/2U hardware platform is particularly suitable for use in large systems as well as in networked Transport and Storage Conditions: branches or subsidiaries. The device supports direct Temperature: 0°C to +40°C...

Table of Contents