Operation; Maintenance - Gardena EasyClean Li Operator's Manual

3. OPERATION

Wait for the engine to stop before you adjust
or transport the product.
To charge the battery [ Fig. O1 / O2 ]:
CAUTION!
Overvoltage damages the battery and
the charging power supply.
v Make sure that you use the correct mains
voltage.
Before you use the battery the first time, the battery must
be completely charged.
The lithium-ion battery can be charged in any state of
charge and the charging process can be disconnected at
any time without to damage the battery (no memory effect).
If the vacuum cleaner switches off during operation, the
battery is empty and must be charged (it may be possible
that the vacuum cleaner can be started again briefly after-
wards, but then switches off automatically immediately).
When the battery charging cable
charging station, the vacuum cleaner can be charged via
the charging station.
v Insert the vacuum cleaner into the charging station.
1. Connect the charging power supply
socket.
2. Connect the battery charger cable
ing socket of the vaccum
ß
station .
Fc
When the battery charging indicator
the battery is being charged.
When the battery charging indicator
green, the battery is completely charged
(charging time, see 7. TECHNICAL DATA).
3. Examine the charge status regularly while you charge.

4. MAINTENANCE

Wait for the engine to stop before you main-
tain the product.
To clean the vacuum cleaner [Fig. M1 ]:
DANGER! Risk of injury!
Risk of injury and risk of damage to the
product.
1. Do not clean the product with water or with a
water jet (in particular high-pressure water jet).
2. Do not clean with chemicals including petrol
or solvents. Some can destroy critical plastic
parts.
(11)
The airflow slots must always be clean.
(1)
1. Remove the nozzle from the suction connection
2. Push the unlock button
(7)
container .
14
(E)
is connected to the
(C)
into a mains
(E)
to the charg-
; – or – of the charging
(Lc) flashes green,
(Lc) illuminates
(6)
and pull off the debris
4. When the battery is completely charged, disconnect the
battery charger cable
5. Disconnect the charging power supply
mains.
Areas of application [ Fig. O3 ]:
To replace the filters, see 4. MAINTENANCE
Clean the vacuum cleaner.
1. For outdoor use:
With coarse filter
2. For indoor use:
(9)
Fine filter with orange ring (not in the scope of
delivery).
The filter cage (8)
filter (9) .
To start the vacuum cleaner [ Fig. O4 ]:
To start:
v Hold the handle
(The start switch remains locked and does not have to
be held).
The vacuum cleaner starts.
To stop:
v Pull the start switch
The vacuum cleaner stops.
To empty the debris container [ Fig. O5 ]:
1. Hold the vacuum cleaner downwards, push the unlock
(6)
button and pull off the debris container
2. Empty the debris container
3. If necessary, clean the filter (see 4. MAINTENANCE).
4. Place the debris container
vacuum cleaner.
5. Push the debris container
hand vacuum cleaner until the unlock button
engages.
3. Empty the debris container
4. Turn the filter cage
the coarse filter cage
5. Remove the filter
6. Clean all removed parts under running water.
7. Clean the suction opening
and the motor unit with a dry cloth.
8. Reassemble all parts in reverse order.
To clean the charger:
Make sure that the surface and the contacts of the
charging socket and the charger always are clean and
dry before you connect the charger.
(2) Do not use running water.
.
Clean the contacts and the plastic parts with a soft and
dry cloth.
(E)
from the charging socket
(C)
from the
(9)
.
must not be mounted without the
(4)
and slide the start switch
(5)
backwards.
(7)
(7)
.
(7) on the bottom of the
(7) against the top of the
(7)
.
(8)
anti-clockwise and remove
(8)
(bayonet lock).
(9)
.
(10)
, the airflow slots
;
.
(5)
forward.
.
(6) audibly
(11)