Summary of Contents for Terex Genie Superlift Advantage SL-5
Page 1
Par ts Manual Par ts & Service Manual Serial Number Range Serial Number Range Superlift from serial number 9594-101 to 5501-15094 Advantage and from SLA02-15095 to SLA04-25258 Part No. 32283 Rev A6 August 2007...
Parts and Service Manual - First July, 2007 Table of Contents Introduction Important Information ...................... ii Section One Safety Rules General Safety Rules ....................iii Section Two Specifications Superlift 5 ..........................2 - 1 Superlift 10 ..........................2 - 1 Superlift 15 ..........................
Page 3
Parts and Service Manual - First Edition TABLE OF CONTENTS Section Four Scheduled Maintenance Procedures, cont. Inspect All Welds ...................... 4 - 5 Clean the Columns ....................4 - 5 Inspect and Lubricate the Winch ................4 - 6 Inspect and Lubricate the Rotating Barrel Handler ........... 4 - 6 Lubricate the Casters and Wheels ................
Page 4
Parts and Service Manual - First August 2007 TABLE OF CONTENTS Section Seven Service Parts How To Order Parts ....................7 - 1 Figure 7-A Decals and Paint (Rev A; August 2007) ..............7 - 2 Figure 7-B Number 1 Mast Attached Parts (Rev A; August 2007) ..........7 - 6 Figure 7-C Standard Base Components (Rev A;...
Page 5
Parts and Service Manual - First Edition This page intentionally left blank. Genie Superlift Advantage Part No. 32283...
Part and Service Manual - First Edition Section 2 - Specifications Specifications Model SL-5 SL-10 SL-15 SL-20 SL-25 Height-Stowed 199 cm 199 cm 199 cm 199 cm 199 cm Width Standard Base 80 cm 80 cm 80 cm 80 cm 80 cm Width - stabilizers lowered Standard Base...
Page 7
Section 2 - Specifications Part and Service Manual - First Edition SPECIFICATIONS Dimensions - Operating SL-5 SL-10 SL-15 SL-20 SL-25 Standard Forks forks down 4 ft 10 9 ft 9 in 14 ft 7 19 ft 6 in 24 ft 4 in 1.5 m 4.5 m 7.4 m...
Page 9
Section 2 - Specifications Part and Service Manual - First Edition This page intentionally left blank. 2 - 4 Genie Superlift Advantage Part No. 32283...
Parts and Service Manual - First Edition Section 3 - Scheduled Maintenance Inspections Scheduled Maintenance Inspections About This Section Dealer service New parts Tools are suggested required required Schedule There are three types of maintenance inspections that must be performed according to a schedule— daily, quarterly and annually.
Page 11
Section 3 - Scheduled Maintenance Inspections Parts and Service Manual - First Edition Maintenance Tables Dealer Table A service Tools are New parts suggested required required Inspect the Operator's Manual Inspect the Decals and Placards Inspect for Damage, Loose or Missing Parts Check the Winch Operation Inspect the Columns for Damage Inspect the Cable and Cable Pulleys...
Page 12
Parts and Service Manual - First Edition Section 3 - Scheduled Maintenance Inspections MAINTENANCE TABLES Dealer Table C service New parts Tools are suggested required required Lubricate the Casters and Wheels Inspect the Mast Assembly for Wear Replace the Winch Friction Disks Inspect the Safety Brake System Inspect the Painted Surfaces Part No.
Section 3 - Scheduled Maintenance Inspections Parts and Service Manual - First Edition Maintenance Inspection Report Model Checklist A Y N R Checklist B Y N R Dealer service Tools are New parts Operator's manual Column hold down suggested Serial number required required Decals and placards...
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures Scheduled Maintenance Procedures About This Section This section contains detailed procedures for each scheduled maintenance inspection. Each procedure includes a description, safety warnings and step-by-step instructions. Observe and Obey: Symbols Legend Indicates the presence of a hazard Maintenance procedures shall be completed by...
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures Table A Procedures 2 Inspect all decals for legibility and damage. Replace any damaged or illegible decal Inspect the Operator's Manual immediately. Maintaining the operator's manual in good Contact your authorized Genie condition is essential to safe machine operation.
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures TABLE A PROCEDURES 2 Raise and lower all columns through a complete cycle. Check the Winch Operation Result: Columns should raise and lower Detection of damage to the winch is essential to smoothly, free of hesitation and binding.
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures TABLE A PROCEDURES Check the Mast for Proper Inspect the Casters and Wheels Sequencing Extremely dirty conditions may require that the casters and wheels be inspected and lubricated Detection of damage to the mast is essential for more often.
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures Table B Procedures Inspect the Column Hold Down Clean the Columns System Clean columns are essential to good machine performance and safe operation. Extremely dirty Detection of damage to the column hold down conditions may require that the columns be system is essential for safe machine operation.
Page 19
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures TABLE B PROCEDURES Inspect and Lubricate the Winch Inspect and Lubricate the Rotating Barrel Handler Maintaining the winch is essential to good machine performance and safe operation. An unsafe Maintaining the barrel handler is essential to good working condition exists if the winch has excessive performance and safe operation.
Page 20
Parts and Service Manual - First Edition Section 4 - Scheduled Maintenance Procedures Table C Procedures Lubricate the Casters and Wheels Inspect the Mast Assembly for Wear Extremely dirty conditions may require that the casters and wheels be inspected and lubricated Detection of excessive or unusual wear in the mast more often.
Need help?
Do you have a question about the Genie Superlift Advantage SL-5 and is the answer not in the manual?
Questions and answers