Output Analog Menu ..........21 BACnet Menu ......22 (BACnet Addressing Setup) Stat Setup Menu ..........23 Display Options Menu ..........24 suPPOrt Having difficulty installing this product? Acutherm is here to help. Application support 510.785.0510 info@acutherm.com acutherm.com ACUTHERM ADVANTAGE - Manual | acutherm.com...
1½ times the duct diameter. MORE BORDER TYPES AVAILABLE. PLEASE SEE INDIVIDUAL MODEL SUBMITTALS FOR MORE DETAILS 6. Connect wall thermostat (see thermostat options pg 4) 7. Connect supply power (see supply power options (pg 2). acutherm.com | ACUTHERM ADVANTAGE - Manual...
1. Field Supplied 2. Transformer 3. APM Normal Operation • Power Signal (green) ‘On’ • Status (red) ‘Flashing’ • Reheat (orange) ‘On’ when heat on • Overload (red) ‘Off’ • Net Health (green) ‘Flash’ with BACnet ACUTHERM ADVANTAGE - Manual | acutherm.com...
DRONE JACK = DRONE DRONE JACK USE C35 CABLES USE C35 CABLES POWER JACK = MASTER POWER JACK = MASTER = DRONE DRONE JACK = DRONE USE C35 CABLES DRONE JACK USE C35 CABLES acutherm.com | ACUTHERM ADVANTAGE - Manual...
Page 6
T’Stat In jack. Setpoint is adjusted using the wall mounted sensor. See page 10 and 11 for more thermostat details. ROOM SENSOR DIAL THERMOSTAT LCD THERMOSTAT LCD THERMOSTAT LCD THERMOSTAT WITH WIRELESS WITH MOTION CO2 AND HUMIDITY THERMOSTAT SENSOR ACUTHERM ADVANTAGE - Manual | acutherm.com...
Page 7
Accessing the damper minimum settings using the menus availble on the LCD thermsotat >Service Menu >VVT >Dpr Cool Min or >Dpr Heat Min (see VVT Menu page 17) • or, if the Advantage is on a BACnet network, setting AV21 Cool Min and AV23 Heat Min acutherm.com | ACUTHERM ADVANTAGE - Manual...
To extend a NETC35 cable use cable coupler (NETCC) • Use either APM or 24 VAC transformer to power Advantage Master unit. Advantage drone units get power from Advantage Master and do not need another transformer RJ12 CABLE SPLITTER CS ACUTHERM ADVANTAGE - Manual | acutherm.com...
Page 9
Advantage Master indicate proper connection. An additional Master unit may be supported from second side of an optional CS (cable splitter) inserted into the Advantage Master power input jack. (see Fig. 6 page 3). acutherm.com | ACUTHERM ADVANTAGE - Manual...
REMOVE the tape until the system is completely balanced. This will ensure that the balancer can provide maximum design cfm without excess air being relieved into the plenum. Premature removal of the tape may impair proper air system balancing. ACUTHERM ADVANTAGE - Manual | acutherm.com...
If Dynamic neutral mode is not required user can force HOT and COLD switch points in the LCD thermostat menu. This method is not recommended, but is available for unique circumstances. >Service Menu >Input >Neutral Mode >Dynamic -> Conventional (see page 19). acutherm.com | ACUTHERM ADVANTAGE - Manual...
Page 12
BACnet option, over the BACnet network. Service Port • LCD Thermostat can also be used as a balancing tool for the Acutherm Intelligent Controller system by simply connecting the RJ-45 cable to the back of the thermostat. ACUTHERM ADVANTAGE - Manual | acutherm.com...
Page 13
LED – 1 blink cooling mode, • Set point limits can be adjusted using the Base 2 – heating, 3 – neutral (receiver) or, with BACnet option, over the BACnet network. Occupancy Override Button Service Port acutherm.com | ACUTHERM ADVANTAGE - Manual...
The Advantage thermostats are all physically the same size surfACe MOunt detAil 1. The Price Intelligent Controller (PIC) Thermostats must be mounted to a wall and wired to the PIC and mounting instructions will be typical. controller via the supplied plenum rated 35ft CAT-5 cable. This cable plugs into the thermostat and the PIC controller with the ease of RJ-45 connections.
Page 15
See DMS Manual for details. CAUTION For accurate flow measurement, the DMS must be installed with correct alignment between diffuser, DMS collar, and flex elbow. acutherm.com | ACUTHERM ADVANTAGE - Manual...
X.XX seQuenCe Displays sequence programmed into stat XXXX inlet siZe Displays inlet size XX inCHes MAC Address Displays current Mac Address deviCe inst. XXXXXXX Displays current Device Instance rOOM teMP (For example) 75.O f ACUTHERM ADVANTAGE - Manual | acutherm.com...
· Displays model (geometry) of Advantage diffuser. Press Menu exit – This will exit the info menu if you select Yes. tO eXit Note: Info menu will automatically time out after 60 seconds. acutherm.com | ACUTHERM ADVANTAGE - Manual...
· Only available with LCD Tstat with CO2 and Humidity (See page 11) exit – This will exit the info menu if you select Yes Press Menu tO eXit Note: Info menu will automatically time out after 60 seconds ACUTHERM ADVANTAGE - Manual | acutherm.com...
*Also available over BACnet network if diffuser has BACnet option installed. TECH TIP VAV diffusers are balanced in the full open position. Use the >BALANCING >DPR. OVERRIDE >GOTO FULL OPN to open the diffuser. Remember to release the override when balancing is complete. acutherm.com | ACUTHERM ADVANTAGE - Manual...
– This will exit the info menu if you select Yes tO eXit Note: Info menu will automatically time out after 60 seconds *Also available over BACnet network if diffuser has BACnet option installed. ACUTHERM ADVANTAGE - Manual | acutherm.com...
Need help?
Do you have a question about the Acutherm Advantage and is the answer not in the manual?
Questions and answers