NuWave OXYPURE ZERO E1000 Quick Start Manual

NuWave OXYPURE ZERO E1000 Quick Start Manual

Hide thumbs Also See for OXYPURE ZERO E1000:

Advertisement

Quick Links

E1000

Getting Started

Function
Button
Name
Turns the OxyPure
POWER
Allows you to run the OxyPure at the lowest fan
AUTO
speed, raising it based on air quality.
ECO
Allows you to save energy by turning the OxyPure
MODE
fan off when it is not needed.
Automatically adjusts to the highest speed for
ULTIMATE
maximum cleaning based on the air quality.
CLEAN
FLOW
Adjusts the louver angles.
ANGLE
FAN
Adjusts the OxyPure's fan speed.
SPEED
Turns off the control panel LED lights but keeps the
SLEEP
fan active.
MODE
Helps limit the amount of time the OxyPure is on.
TIMER
Cleans the air using the highest speed for a set time
TURBO
(½ hour, 1, or 2 hours).
Use
on and off.
Press Power to turn the OxyPure
®
Press AUTO and the Auto back light will turn on. There is no time limit on the Auto Mode. Press
AUTO again to deactivate Auto Mode.
Press and hold AUTO for 1 second to activate Eco Mode. When the air quality is poor, the unit will
automatically run. When the air quality is good, the unit will turn off. Press AUTO and hold for 1
second to deactivate Eco Mode.
Press ULTIMATE CLEAN to activate the Ultimate Clean Mode.
Press AIR FLOW ANGLE to adjust the louver angles from 30°, 60°, 90°.
There are 6 fan speed levels. Press FAN SPEED to adjust from Speed 1 (lowest) to Speed 6
(highest).
Adjust the Fan Speed prior to activating Sleep Mode. Press and hold FAN SPEED for 2 seconds
to activate Sleep Mode. Press any button to deactivate it.
The timer is adjustable from ½ hour to 1, 2, 4, 8, or 12 hours. To set the timer, press TIMER.
Press TURBO once to run the OxyPure at the highest speed for ½ hour. Press TURBO twice for 1
hour. Press TURBO three times for 2 hours.
Quick Start Guide
Refer to the Owner's Manual for more details
Model No: 47251 / 47261
Air/Odor Quality - Detects particles as small as 2.5/1000mm
Clean
Particulate Matter (PM) with a diameter of 2.5 microns or less
0~5
5~10
10~20
20~30
Fan Speeds
1
2
3
See the Owner's Manual for details.
on and off.
®
Dirty
30~50
Over 50
4
5
6

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OXYPURE ZERO E1000 and is the answer not in the manual?

Questions and answers

Summary of Contents for NuWave OXYPURE ZERO E1000

  • Page 1 Quick Start Guide Refer to the Owner’s Manual for more details Model No: 47251 / 47261 E1000 Air/Odor Quality - Detects particles as small as 2.5/1000mm Clean Dirty Particulate Matter (PM) with a diameter of 2.5 microns or less 5~10 10~20 20~30 30~50...
  • Page 2 ’s Wi-Fi lets you operate it from anywhere. ® To set up and activate the Wi-Fi: Filters (Lifespan up to 20 years) Bio-Guard ® Download the NuWave Connect app (Apple Store or Google Play) to your ® ™ • 8,000-volt electrostatic filter kills 99.99% of mold, bacteria, and viruses.
  • Page 3 The FILTER 2 and FILTER 4 lights will turn green in about 3 months to alert you that the Bio-Guard filters SHOULD be cleaned to maintain ® optimal performance (NuWave Recommendation). When either light turns red (after about 6 months), that Bio-Guard filter MUST be cleaned. ®...
  • Page 4 1. Use a brush-tipped vacuum to remove any dust or lint. reason, the OxyPure will not operate and you will need to contact NuWave Customer Service. Exercise caution to ensure the tabs Cleaning the Odor Sensor The Odor Sensor is behind the three slots above the Dust Sensor are not damaged when securing the Filter Access Panel.

This manual is also suitable for:

4725147261

Table of Contents