Table of Contents
Advertisement
Available languages
Available languages
OPERATION (FIG. A)
WARNING: To Reduce The Risk Of Electric Shock –
Use indoors only.
WARNING: To reduce the risk of serious personal
injury, turn unit OFF before making any
adjustments or removing/installing attachments
or accessories. An accidental start-up can
cause injury.
WARNING: Projectile/Respiratory Hazard: Never use
the vac without its filter.
Installing and Removing the Battery Pack
(Fig. D)
WARNING: Ensure the tool/appliance is in the off
position before inserting the battery pack.
NoTE: For best results, make sure your battery pack is
fully charged.
To install the battery pack
battery pack with the rails inside the tool's handle and slide it
into the handle until the battery pack is firmly seated in the
tool and ensure that it does not disengage.
To remove the battery pack from the tool, press the release
button
5
and firmly pull the battery pack out of the tool
handle. Insert it into the charger as described in the charger
section of this manual.
On/Off Switch (Fig. I)
NoTE: This product is for dry pick-up only.
•
To switch the vac on, slide the On/Off switch
•
To switch the vac off, slide the On/Off switch back.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories, when
replacing line, or prior to cleaning. An accidental
start-up can cause injury.
Your D
WALT power tool has been designed to operate
e
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the
risk of eye injury, always wear approved eye protection
when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
6
into the tool handle, align the
1
Cleaning/Emptying the Dust Bowl and
Filter (Fig. D, E, J, K)
WARNING: Projectile/Respiratory Hazard: Never use
the vac without its filter.
WARNING:
•
•
•
•
NoTE: The filter is reusable, do not confuse it with a
disposable dust bag, and do not throw it away when the
product is emptied. We recommend that you replace the
filter every 6–9 months depending on frequency of use.
Removing Filter
1. Place the vacuum over a trash bin and remove the
dust bowl
dust bowl release button
the dust bowl by pulling the dust bowl away from the
main housing.
2. Remove the filter assembly
dust bowl.
3. Twist counterclockwise and pull the filter cap
seperate it from the filter
Install Filter
1. Attach the filter cap onto the filter and rotate it clockwise
to lock it firmly into position.
2. Push the filter assembly into the dust bowl.
forward.
3. Install the dust bowl onto the main housing and lock it
firmly into position.
Cleaning
IMpoRTaNT: Maximum dust collection will only be
obtained with a clean filter and an empty dust bowl. If dust
begins to fall back out of the product after it is switched off,
this indicates that the bowl is full and requires emptying.
1. Once the filter is removed from the dust bowl, shake off
or lightly brush any dust from the filter.
2. Empty any dust from the dust bowl
and wash if necessary.
3. Rinse out the dust bowl with warm soapy water. Ensure
that the dust bowl is completely dry before using.
4. Wash the filters regularly using warm, soapy water and
ensure that it is completely dry before using again. The
cleaner the filter is, the better the product will perform.
5. It is very important that the filters are completely dry and
correctly in position before use.
6. Ensure the filters are completely dry for 24 hours
before refitting.
Replacement HEPA filter: DCV5011H
Do not use damaged filters. Replace any damaged filters
immediately.
Do not wash the inside of the filter.
Let the filter dry thoroughly if the inside becomes wet.
Do not use a brush to clean the filter.
Never use compressed air or a brush to clean filters,
otherwise damage to the filter membrane will occur
which will allow dust to pass through the filter.
2
from the main housing by pressing the
3
on the handle and remove
4
by pulling it out of the
20
.
ENglIsh
21
to
2
into a trash bin
25
Advertisement
Table of Contents
