Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for JAMO LKP4.6
Summary of Contents for JAMO LKP4.6
- Page 1 LKP4.6 Installation & User Guide...
- Page 2 The LKP4.6 is a sophisticated learning keypad which adds convenient wall mounted source con- trol to the Jamo AVD4.6 multi-room A-BUS system. The LKP4.6 is connected and installed next to the KP4.6 amplified keypad. The source equipments IR codes are learned from the individual source equipments remote controls into the Jamo LRC4.6...
-
Page 3: Table Of Contents
Content Important Installation Controls Display Programming Cloning 11-12 Operation Alarm Function Sleep Function Setup Function Configure Function Learn Function Specifications Troubleshooting Limited Warranty... -
Page 4: Important
Important The LKP4.6 is installed together with the KP4.6 in a double gang J box. All knock outs should be removed to provide ventilation. Do not install the LKP4.6/KP4.6 in a box that also has electrical installation in it. If installed next to electrical installation either a barrier-box or two boxes must be used. -
Page 5: Installation
Installation The LKP4.6 can be installed together with any KP4.6 in the system, both main zones and sub-zones. Example of wiring diagram below of two main zones with an LKP4.6 in one of the zones. Speakers Speakers Speaker cables Speaker cables KP4.6... - Page 6 Installation The LKP4.6 is installed together with the KP4.6 in a dou- ble gang J box. A double decora style face plate (not in- cluded) is placed over the front as shown. The LKP4.6 is connected to the KP4.6 using the supplied ribbon cable.
- Page 7 Installation LKP4.6 rear panel connections. 1. KP4.6 Connector Connects to the KP4.6 with the supplied cable. 2. I.C.P. In-circuit programming socket. Used to upload software during manu- facturing.
-
Page 8: Controls
9 SHIFT / SET (settings) 10 Cloning Port 11 Display Screen The FAV 1 (favorite) button in this example has been programmed to Power button. Note: The functions of buttons 1-8 only operates after the LKP4.6 has been cloned from the LRC4.6. -
Page 9: Display
1. Week days. Bar over letter indicates day of week. 2. Alarm icon. Displayed when alarm is set. 3. IR. Indicates IR signal is sent from the LKP4.6. 4. Time. PM is used when set for 12 hour clock (page 17). -
Page 10: Programming
Programming Before the LKP4.6 can be used it must be programmed using an LRC4.6. First. • Teach IR codes and set macros in the LRC4.6. • Name the sources and buttons in the LRC4.6. • Set the time and date in the LRC4.6. -
Page 11: Cloning
Cloning Step 1. Remove the plug from the Cloning Port on the LKP4.6. Step 2. Insert the cloning cable (supplied with LRC4.6) into the Cloning Port on LKP4.6 port LRC4.6. Step 3. Put the LKP4.6 into Learn mode. Press and hold the SET button. Release when LEARN? is displayed on the screen. - Page 12 Start cloning. Press ENTER on the remote. Display shows SENDING. Step 7. Confirm the LKP4.6 is receiving. RXING will be displayed to indicate it is receiving data. After approximately 7 minutes the keypad should show COMPLETE for a few seconds and return to normal op- eration.
-
Page 13: Operation
Operation After the setup and cloning you can now operate the source equipment with the LKP4.6 as well as perform various timer functions. The LKP4.6 will always be in primary functions unless changed by the user. Press the SHIFT button briefly to switch between primary and secondary functions of keys 1-8. -
Page 14: Alarm Function
On/Off: When alarm is set to on, the alarm icon will appear in the display. At the time set the KP4.6/LKP4.6 will turn on to the se- lected source and send the FAV 1 code or macro (if any). Alarm? menu... -
Page 15: Sleep Function
Use the buttons to adjust the option. Press EXIT to return to normal operation. This menu allows you to set a time when the LKP4.6 automatically turns off the zone or sub-zone it is located Sleep? menu Hour... -
Page 16: Setup Function
Press EXIT to return to normal operation. This menu lets you set the time, date and year of the LKP4.6. The order of the month and date is set in the Config? menu (page 17). Note: The time, date and year is set automatically to the time, date and year of the LRC4.6 during cloning (page... -
Page 17: Configure Function
Configure Function Press and hold the SET button. Release when CONFIG? is displayed on the screen. Use the buttons to navigate the options. Use the buttons to adjust the option. Press EXIT to return to normal operation. 12/24 Hour: Sets the clock to 12 or 24 hour format. DD/MM: Sets the display order of date and month. -
Page 18: Learn Function
1. Unplug power to the system and plug back in after 1 min. 2. When power resumes keypad displays distorted text. 3. Clone the LRC4.6 to the LKP4.6 without entering LEARN? 4. When LRC4.6 is done SENDING, repeat point 1 above. Note: Time and date will not be updated in the LKP4.6. -
Page 19: Limited Warranty
Limited Warranty The warranty period will come into force as from the purchase date stated on the invoice. The warranty will apply for 2 years. In case of warranty inquiries, please contact your dealer. In case of request for service under warranty, enclose the origi- nal receipt. - Page 20 www.jamo.com...