Advertisement
9. RADIO CONFIGURATION MENU
>3s
RADIO ASSIGNMENT BETWEEN AN MTR RECEIVER MODULE AND THE
MD3300MRP LOAD MANAGER
For correct operation, it is essential to configure a radio assignment between
the MD3300MRP load manager and the MTR2000ERP(X) or MTR2000MRP(X)
radio receiver relays. The MD3300MRP device is able to manage up to 7
receiver modules directly connected. If you wish to manage more than 7
modules, it is necessary to create a radio bus to allow communication between
the MD3300MRP device and the subsequent modules.
Only one MD3300MRP device can be configured on each system.
▶ On the MD3300MRP device, access the RADIO configuration menu by
simultaneously pressing keys
display shows "bind.r1".
You can cancel the assignment operation by pressing
▶ Press
key on the device to perform radio assignment.
▶ While "InProG" is flashing (for 30 seconds), press briefly with a sharp,
properly insulated tool into the "Connect" hole on the receiver module.
▶ The MD3300MRP device will briefly display the message "PASS" if the
assignment has been successful. The receiver module is now correctly
assigned to the MD3300MRP device.
▶ If the device displays the message "Err. 03" the assignment has not been
successful. Repeat the operation and make sure to press into the "Connect"
hole on the receiver module within the 30 seconds in which the MD3300MRP
load manager displays the message "InProG".
In some cases, if the receiver is out of radio range, it is possible that the
load manager is unable to communicate with the receiver and displays
the message "Err. 03". In this case, refer to paragraph "Extending the
range".
▶ It is necessary to repeat the entire assignment procedure for each receiver
module you wish to assign directly to the MD3300MRP device.
REMOVING ONE SINGLE RADIO ASSIGNMENT
It is possible to remove an assignment between an MTR receiver module and
the MD3300MRP load manager.
▶ On the MD3300MRP device, access the RADIO configuration menu by
simultaneously pressing keys
display shows "bind.r1".
▶ Press the arrow key
or
You can cancel the assignment operation by pressing
▶ Press
to remove the assignment.
▶ While "InProG" is flashing (for 30 seconds), press briefly with a sharp,
properly insulated tool into the "Connect" hole on the receiver module.
▶ The MD3300MRP load manager will briefly display the message "PASS" if
the receiver module assignment removal has been successful.
▶ If the device displays the message "Err. 03" the assignment removal has
not been successful. Repeat the operation and make sure to press into the
"Connect" hole on the receiver module within the 30 seconds in which the
MD3300MRP load manager displays the message "InProG".
Radio assignment
and
(for approx. 3 seconds) until the
and
(for approx. 3 seconds) until the
until "dEL .r6" is displayed.
Removing a
radio assignment
DEVICE SCAN FOR YOKIS PRO APP
The scanning operation allows the MD3300MRP device to be detected by
the Yokis Pro App in order to subsequently carry out the assignment to the
channels and the parameter configuration (Paragraphs 10 and 11) directly
from the App.
▶ On the MD3300MRP device, access the RADIO configuration menu by
simultaneously pressing keys
display shows "bind.r1".
▶ Press the arrow key
You can cancel the scan by pressing
▶ Press the key
key.
▶ While "InProG" is flashing (for 30 seconds), start the device search on the
Yokis Pro App and select it.
▶ The MD3300MRP load manager briefly displays the message "PASS" if
the device has been detected and selected by the Yokis Pro App.
▶ If the device displays the message "Err. 03" the detection has not been
successful. Repeat the operation and make sure to start the device search
on the Yokis Pro App within the 30 seconds in which the MD3300MRP
load manager displays the message "InProG".
For more details on channel assignment and configuration of the
MD3300MRP device through the Yokis Pro App, scan the QR Code
at the beginning of the booklet to download the booklet.
REMOVING ALL RADIO ASSIGNMENTS
It is possible to remove all assignments between the various receiver
modules and the MD3300MRP load manager.
▶ On the MD3300MRP load manager, access the RADIO communication
menu by simultaneously pressing keys
until the display shows "bind.r1".
▶ Press the arrow key
▶ Press the key
▶ The MD3300MRP device will briefly display the message "PASS". All
assignments with receiver modules have been removed.
EXTENDING THE RANGE
All YOKIS radio receivers also work as signal repeaters. The addition of one
or more modules allows extending the radio range by creating a Radio Bus
key.
between the various modules on the system.
1) Creating the Radio Bus
▶ Press once the Connect button of A module (the LED of A module starts
flashing), then press once the Connect button of B module (connection
between A and B is created and the 2 modules stop flashing).
▶ The two buttons must be pressured within a maximum of 30 seconds.
▶ Perform the same operation between B and C modules and so on with
the other modules.
Removing all
Scan
radio assignments
Procedure completed
Procedure failed
and
or
until "SCAn" is displayed.
to start the detection.
until "CLEAr" is displayed.
to delete all assignments.
>4 sec.
>4 sec.
(for approx. 3 seconds) until the
key.
and
(for approx. 3 seconds)
Advertisement
