Advertisement
Dakota Instruction
Before assembling your
greenhouse please read all
instructions, while watching the
instructional video.
This manual includes instructions for ALL add-
ons that you can purchase with your greenhouse.
For additional assistance call 1(866)928-3390
Manual
Table of Contents
Page 2
Page 4
Page 6
Page 8
Page 9
Page 10
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Growers SOLUTION Dakota
Summary of Contents for Growers SOLUTION Dakota
-
Page 1: Table Of Contents
Dakota Instruction Manual Before assembling your greenhouse please read all instructions, while watching the instructional video. This manual includes instructions for ALL add- ons that you can purchase with your greenhouse. For additional assistance call 1(866)928-3390 Table of Contents Greenhouse Instructions... -
Page 2: Greenhouse Instructions
DAKOTA GREENHOUSE INSTRUCTIONS !!!! CAUTION: Tubing ends may be sharp!!! Step 1 – Ensure all components are accounted for. • Lay out all bundles and open all boxes to compare labeled pieces to the packing sheet you received. • Check for any concealed damage or missing components, please,... - Page 3 • Ensure on the first and last bow that the tek screws are underneath the bows, facing the inside of the green house. Step 5 - Purlin • ** All Dakota houses get 3 runs of purlin, the additional 2 mounted at 10 and 2 o'clock.** Fig 5.1 •...
-
Page 4: Wind Bracing
Step 7 -Truss and Gusset Only on 16' kits. • All truss and gusset mounting is done with tension bands. Be sure to secure the bands with a tek screw through the band into the bow material. • For the gusset bracing measure 52" for the 16' house, 42"... - Page 5 Step 9 – Wire Lock • Lay your wire base down the length of the house. • By using either a 1/8" drill bit or tekscrew, pre-drill the aluminum base for the wood screws. • Start the wire base 1 1/2" in from the end of the board. This leaves room for the base that goes over the first and last bow.
-
Page 6: End Wall Kits
• Drive a 1” ground stake in each of these two points . This is where your storm door will be. (Figure 3.1). Step 4 - THIS STEP IS ONLY FOR 20' DAKOTA GREENHOUSE • From that point if you have another upright measure 48” over and drive another 1” ground stake. (Fig 4.1). - Page 7 • On the inside of the house place one self-tapping tek screw through the tension band securing it to the bow. (Fig 9.1). Figure 9.1 Step 10 - ONLY ON 20' DAKOTA GREENHOUSE • You may install end braces at 60” (Fig 10.1). Figure 10.1 Step 11 •...
-
Page 8: Roll-Up Side
ROLL UP SIDE INSTRUCTIONS Step 1 • A 1.1) with two tek screws. Step 2 Figure 1.1 • Lay pipe on top of bottom board and attach the bottom pipe clamps (Fig 2.1). Snap them evenly spaced along the pipe making sure that you have the film snug at the base. -
Page 9: Spin Handle
Step 4 SPIN HANDLE INSTRUCTIONS Step 1 Figure 1.1 • Slip small sleeve over the bolt. (Fig 1.1) Step 2 • Slip large sleeve over small sleeve on bolt. Step 3 • Insert thru pre-drilled hole. Attach nut and tighten. (Fig 3.1) Figure 5.1... -
Page 10: Wind Strapping
WIND STRAPPING INSTRUCTIONS Step 1 • The best way to throw your wind strapping over the green 1.1) and throw over the greenhouse. Step 2 • Place wind strapping between the first and second bow and then between the next to last and the last bow. With the remaining wind strapping equally space your strapping the length of your green house.
Need help?
Do you have a question about the Dakota and is the answer not in the manual?
Questions and answers