Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Growers SOLUTION Manuals
  4. Greenhouse Kit
  5. Quonset Low Sidewall
  6. Manual

Growers SOLUTION Quonset Low Sidewall Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
These Photo's are for
Reference only.
All Greenhouses are assembled in a similar
fashion. Use these Photo's as a guide along
with your instruction manual. If you are unsure
about assembly, Call Us @ 866-928-3390

Advertisement

loading
Need help?

Need help?

Do you have a question about the Quonset Low Sidewall and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Growers SOLUTION Quonset Low Sidewall

Summary of Contents for Growers SOLUTION Quonset Low Sidewall

  • Page 1 These Photo’s are for Reference only. All Greenhouses are assembled in a similar fashion. Use these Photo’s as a guide along with your instruction manual. If you are unsure about assembly, Call Us @ 866-928-3390...
  • Page 2 Quonset Greenhouse...
  • Page 3 Low Sidewall Greenhouse...
  • Page 4 High Sidewall Greenhouse...
  • Page 5 Figure 1.1 - Taking Measurements on outer edge...
  • Page 6 Figure 1.2 - Use string around all 4 corners...
  • Page 7 Figure 2.1 - Lay bows flat and slide together...
  • Page 8 Figure 2.2 - Secure joints with 2 Tek-Screws...
  • Page 9 Figure 4.3 - Connect purlin using 2-hole strap, on the first and last bow...
  • Page 10 Figure 4.4 - Use purlin clamps on remaining bows...
  • Page 11 Figure 5.1 - Attach base board with 2-hole straps down sides. Attach base board with L brackets on endwalls.
  • Page 12 Figure 5.2 – Attach hip/head board with 2-hole straps down sides. Place a Tek- screw through 2-hole strap to secure to ground stake.
  • Page 13 Figure 7.1 - Attach wire base on hip/head board if you have rollup sides. Attach wire base to base board if you do not have rollup sides.
  • Page 14 Figure 7.2 - Place a wire base between hip board and base board...
  • Page 15 Figure 7.3 - Attach wire base to face of hip/head board...
  • Page 16 Figure 8.1 - Lay film over wire lock channel and fasten with wire lock...
  • Page 17 End Wall Instruction Pictures...
  • Page 18 Figure 2.1 – For 36” Door Opening. Find Center of greenhouse then measure 18.5” to the left and right...
  • Page 19 16 ft Low Sidewall End Walls...
  • Page 20 20 ft Low Sidewall End Walls...
  • Page 21 24 ft Low Sidewall End Walls...
  • Page 22 30 & 32 ft Low Sidewall End Walls...
  • Page 23 Figure 3.1 - Drive 1” ground stakes into position based on layout.
  • Page 24 Figure 5.1 - Measure distance between ground stakes and peak of bow...
  • Page 25 Figure 6.1 - Insert square upright over ground stake. Secure with Tek-screws on inside side of upright.
  • Page 26 Figure 7.1 - Attach brace bands over the bow and into the square upright...
  • Page 27 Figure 8.1 - Insert bolt through brace band and secure on inside of greenhouse...
  • Page 28 Figure 9.1 - Place self-tapping TEK screw through brace band to secure.
  • Page 29 Figure 10.1 - Install header supports at chest height.
  • Page 30 Figure 11.1 - Use TEK screws to install header with L brackets.
  • Page 31 Figure 13.1 - Use Door frame to seal the end film around the opening.
  • Page 32 Roll Up Side Instruction Pictures...
  • Page 33 Figure 1.1 - Hip Board and Base Board...
  • Page 34 Figure 2.1 - Mount 2-hole straps...
  • Page 35 Figure 3.1 - Attach film to wire-lock base...
  • Page 36 Figure 4.1 - Slide and secure pipes with 2 Tek-screws...
  • Page 37 Figure 5.1 – Roll poly around pipe and secure with Snap Clamps...
  • Page 38 Figure 6.1 - Fender washer to reinforce strapping...
  • Page 39 Figure 6.2 - Fold ends of strapping twice.
  • Page 40 Figure 6.4 - Mount on hip board and base board...
  • Page 41 Figure 6.3 - Pull Strapping tight...
  • Page 42 Figure 6.5 - Pipe sticks out about 1 foot on each end.
  • Page 43 Figure 7.1 - Place handle on pipe and secure with 2 Tek-screws.
  • Page 44 Figure 8.1 - Use strapping to secure handle to the greenhouse.
  • Page 45 Roll Up Door Instruction Pictures...
  • Page 46 Figure 2.1 - Attach roll-up door film...
  • Page 47 Figure 3.1 - Roll film up on pipe to the inside...
  • Page 48 Figure 4.1 - Place one clip at each end and in the center...
  • Page 49 Figure 5.1 - Assemble the swivel handle...
  • Page 50 Figure 5.2 - Attach the knuckle to the door pipe.
  • Page 51 Figure 5.5 - Attach extension pipe to knuckle.
  • Page 52 Figure 5.3 - Slip boot onto pipe. Attach Handle to extension pipe.
  • Page 53 Figure 5.4 - Slip boot over the knuckle and place zip ties to hold it in place.
  • Page 54 Figure 6.1 – Attach Wind Strapping to the upright on top. Fold over end to reinforce and place Tek-screws.
  • Page 55 Figure 6.2 - Fold over end to reinforce, pull tight and place Tek-screws.
  • Page 56 Figure 7.1 - Trim existing Greenhouse Film.
  • Page 57 Figure 8.1 - Use wire-lock to seal door along the sides when needed.
  • Page 58 Spin Handle Instruction Pictures...
  • Page 59 Figure 1.1 - Slip small sleeve over the bolt...
  • Page 60 Figure 2.1 - Slip large sleeve over small sleeve...
  • Page 61 Figure 3.1 - Insert through hole, attach nut and tighten...
  • Page 62 Wind Bracing Instruction Pictures...
  • Page 63 Wind Strapping Instruction Pictures...
  • Page 64 Figure 1.1 - Tie strapping onto a bottle...
  • Page 65 Figure 2.1 - Place strapping between hoops evenly for the size greenhouse you have. IT IS NOT REQUIRED BETWEEN EVERY BOW! If you wish to do this you will need to purchase additional strapping.
  • Page 66 Figure 3.1 - Fold over strapping twice for strenght...
  • Page 67 Figure 3.2 - Use washer and wood screws to attach...
  • Page 68 If you have questions please check out Grower’s Learning FAQ section. If you still need help please give us a call at 866.928.3390.