Ideal Security BK6311 Manual page 4

OPERATION
SET-UP YOUR WIRELESS BED ALARM QUICKLY WITH THE FACTORY LINKED SOUND
The shipped transmitter and receiver were factory linked to sound #5 already.
1. Plug the connectors of the transmitter and weight sensing pad together.
2. Place the weight sensing pad on a big flat surface that can support the entire pad.
3. Place the transmitter away from the pad, not on the pad. You can position the transmitter
using the included double-sided tape or you can simply place it on a surface close by
(i.e., bedside table).
4. On receiver, slide the POWER and SOUND switches to the ON position.
• You will immediately hear a beep. Now the system is in standby/ready mode.
• The ARMED middle LED light will flash every 3 seconds indicating the system is ready.
5. The transmitter is armed when the pad senses weight. To test, sit on pad.
6. A signal will trigger when the weight is removed from pad. To test, sit up and off of pad.
Sound ON mode: When the sensor is triggered, the alarm will sound, and lights will flash.
Sound OFF mode: When the sensor is triggered, only lights will flash.
To stop the alarm: If sounds 1 - 4 are selected, the alarm will end on its own. If a "forever"
alarm is selected (#5 or #6), slide the POWER switch to OFF position.
To restart the alarm: If sounds 1 - 4 are selected, the alarm is ready on its own. If a "forever"
sound is selected (#5 or #6), slide the POWER to the OFF position then to the ON position.
BATTERY LOW INDICATOR
When the batteries in the receiver alert are low, the right LED (#4 description of components
receiver) will flash once every four seconds.
When the batteries in the transmitter are low, the integrated LED will flash slowly, 3 seconds ON,
one second OFF. Also, the #2 LED in the receiver will flash.
Change the batteries immediately when battery is low.
LINKING A TRANSMITTER AND RECEIVER
The shipped transmitter and receiver were factory linked to sound #5 already.
These instructions are for linking a new transmitter to a receiver.
1. Plug the connectors of the transmitter and weight sensing pad together.
2. Place the weight sensing pad on a big flat surface that can support the entire pad.
3. Place the transmitter away from the pad, not on the pad, you can position the transmitter
using the included double-sided tape or you can simply
place it on a surface close by (i.e., bedside table).
4. On receiver, slide the POWER switch to ON position.
5. On receiver, slide the SOUND switch to ON position.
6. Sit on the pad. You will sit on the pad during the whole
process unless otherwise instructed.
7. On receiver, slide the POWER switch to OFF position.
8. Sit on the pad continuously for at least 15 seconds.
9. On receiver, slide the POWER switch to ON position.
10. Locate the learn button on the back of the receiver,
push it for 1 second then release (Fig. 4).
11. You will hear a sound. If you like the sound, go to next step, otherwise, push the button
again for 1 second then release to hear the next sound, you can cycle this way through all
available sounds.
12. Once you hear the sound you like, push the learn button continuously for 3 seconds
until you hear a beep. Release the button. Now the receiver is ready to accept the new
transmitter.
13. Stand up from the pad.
14. You will hear one long beep sound. That means the linking (learn) is successful.
15. If you hear 4 short beeps, that means the linking has failed. Slide POWER to OFF on the
receiver then restart the procedure from step 1.
16. Test the system again.
17. On the receiver, make sure POWER and SOUND are set to ON.
18. Sit back on the pad for 5 seconds.
19. Stand up and off the pad.
20. You will hear the sound you selected for the duration associated with the sound. That
means the system works.
21. For sound #5 and #6 where the sound continues indefinitely, you can turn POWER to OFF
on the receiver and turn it back ON. This will not erase the linked transmitter.
Now you have successfully linked a new transmitter to a receiver.
ASSIGNING A NEW SOUND OR REMOVING A TRANSMITTER
Follow the instructions below if you want to:
• Change the default sound #5, you can choose a new sound and link to the transmitter
• Unlink (remove) a transmitter
• Relink a transmitter to receiver after system has been inactive for a period of time
1. On receiver, make sure POWER is set to OFF.
2. Do step 1 to 7 as described in the section above.
3. Locate the LEARN button on the back of the receiver, push it continuously for 12 seconds
until you hear two long beeps, release the button. This will erase all linked transmitters from
the receiver. You cannot erase only one transmitter.
4. Do step 8 to 21 in the section above.
CLEANING, CARE AND MAINTENANCE
While the pad is splash resistant, it is not water-proof and is not designed for submersion
in water.
We recommend placing the weight sensing pad under a washable bedding or incontinence pad.
LEARN Button
Be sure to test the function before using. If the protective layer is too heavy, it may prevent the
weight sensing pad from properly detecting weight changes.
To clean the pad, we recommend using disinfectant or anti-bacterial wipes.
If soiled, you may also clean the pad by using a mild soap in a spray bottle. Lightly spray the
pad on both sides, taking care not to spray near the connector jack or where the wire enters the
LEARN
pad. Wipe down with a dry sponge or towel.
DO NOT submerge the pad in water or spray directly with water from a shower, hose, or faucet.
DO NOT use the pad when folded, as applying pressure could damage the internal circuitry.
Take the batteries out when the device will be out of use for a long period.
(Fig.4)
IMPORTANT NOTES
• Before installing permanently, test the reception range of the receiver. If the receiver does
not pick up the signal from a transmitter, try another location closer to the transmitter.
• The components are designed for indoor use only. Do not install the receiver or transmitter
where they will be exposed to direct sunlight, rain, or extreme cold environment.
• The sound coming from the receiver can be very loud. Never put the speaker close to your ear.
• For the most up to date installation instructions, videos and troubleshooting information
consult our web site, www.idealinc.com
• This wireless bed alarm can provide additional security for your family and loved ones
if utilized properly. However, its use cannot guarantee complete protection against falls
or injury. Ideal Security cannot assume any responsibility for any damages as a result of
installing this or any other Ideal Security product.
WARRANTY
This unit is warranted to be free of defective materials and workmanship for a period of one
year from date of purchase. Please keep your bill of sale. In case of malfunction, this unit will
be replaced at no charge by Ideal Security Inc. Warranty begins on date of consumer purchase.
Replacement as described above shall be the sole remedy to the consumer and there shall be
no liability on the part of Ideal Security Inc. for any special, indirect, incidental or consequential
damages, including but not limited to any loss of business or profits whether or not foreseeable.
For more information, visit www.idealinc.com/policies
CUSTOMER SERVICE
Thank you for your purchase.
We are dedicated to customer service and will work to resolve any difficulties to ensure
customer satisfaction.
If you have any questions about the setup or function of this product, please contact us before
returning it.
Tel.: 1-800-361-2236 Support and Contact: www.idealinc.com/help
Email: info@idealinc.com FAQ and Videos: help.idealinc.com
www.idealinc.com
This device complies with Part 15 of the FCC Rules and RSS-210 of industry Canada.
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation of
the device.
Warning: Changes or modifications made to this equipment not expressly approved by the party responsible for
compliance may void the user's authority to operate this equipment.
X6311INS – 2022