Specifications; Safety Check-Out; Unleaded Solder - Sony Cyber-shot DSC-W580 Service Manual

Ver. 1.2 2011.09
Camera [Input and Output connectors]
Multi use terminal: Type3a
[System]
Image device: 7.75 mm (1/2.3 type)
color CCD, Primary color filter
Total pixel number of camera:
Approx. 16.4 Megapixels
Effective pixel number of camera:
USB communication: Hi-Speed USB
Approx. 16.1 Megapixels
Lens: Carl Zeiss Vario-Tessar 5× zoom lens
f = 4.5 mm – 22.5 mm (25 mm –125 mm
[LCD screen]
(35 mm film equivalent))
LCD panel:
F2.6 (W) – F6.3 (T)
While shooting movies (16:9):
Total number of dots:
28 mm – 140 mm
While shooting movies (4:3):
34 mm – 170 mm
[Power, general]
SteadyShot: Optical
Power: Rechargeable battery pack
Exposure control: Automatic exposure,
Scene Selection (12 modes)
White balance: Automatic, Daylight,
Cloudy, Fluorescent 1/2/3,
Power consumption (during shooting):
Incandescent, Flash, One Push
Underwater White Balance: Auto,
Operating temperature:
Underwater 1/2, One Push
Recording interval for Burst mode:
Storage temperature:
Approx. 1.0 second
File format:
Dimensions:
Still images: JPEG (DCF Ver. 2.0,
Exif Ver. 2.3, MPF Baseline)
compliant, DPOF compatible
Movies: MPEG-4 Visual
Mass (including NP-BN1 battery pack,
Recording media: Internal Memory
(Approx. 27 MB), "Memory Stick
Duo" media, SD cards
Microphone: Monaural
Flash: Flash range (ISO sensitivity
Speaker: Monaural
(Recommended Exposure Index) set to Auto):
Exif Print: Compatible
Approx. 0.2 m to 3.7 m (W)
PRINT Image Matching III:
(7 7/8 inches to 12 feet 1 3/4 inches)
Approx. 1.0 m to 1.5 m (T)
(3 feet 3 3/8 inches to 4 feet 11 1/8 inches)
Model information table
Model DSC-W580
Destination CND, E, KR
Color system NTSC
TransferJet
• Abbreviation
CND : Canadian model
KR : Korea model
DSC-W580_L2

SPECIFICATIONS

BC-CSN/BC-CSNB battery
charger
(AV-out (SD/HD Component)/
Power requirements: AC 100 V to
USB/DC-in):
240 V, 50/60 Hz, 2 W
Video output
Output voltage: DC 4.2 V, 0.25 A
Audio output (Monaural)
Operating temperature:
USB communication
0°C to 40°C (32°F to 104°F)
Storage temperature:
(USB 2.0)
–20°C to +60°C (–4°F to +140°F)
Dimensions:
Approx. 55mm × 24mm × 83mm
(2 1/4 inches × 31/32 inches × 3 3/8 inches)
7.5 cm (3.0 type) TFT drive (W/H/D)
Mass: Approx. 55 g (1.9 oz)
230 400 (960 × 240) dots
Rechargeable battery pack
NP-BN1
Used battery: Lithium-ion battery
NP-BN1, 3.6 V
Maximum voltage: DC 4.2 V
AC-LS5 AC Adaptor (sold
Nominal voltage: DC 3.6 V
separately), 4.2 V
Maximum charge voltage: DC 4.2 V
Maximum charge current: 0.9 A
1.1 W
Capacity:
typical: 2.3 Wh (630 mAh)
0°C to 40°C (32°F to 104°F)
minimum: 2.2 Wh (600 mAh)
–20°C to +60°C (–4°F to +140°F)
Design and specifications are subject to
change without notice.
94.0 mm × 56.0 mm × 19.1 mm
(3 3/4 inches × 2 1/4 inches × 25/32 inches)
(W/H/D, excluding protrusions)
"Memory Stick Duo" media):
Approx. 127 g (4.5 oz)
Compatible
UK AEP, E
PAL PAL
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY
SONY.
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are "pinched"
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of
deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Set the soldering iron tip temperature to 350 °C approximately.
• Do not touch the soldering iron on the same conductor of the circuit
board (within 3 times).
• Be careful not to apply force on the conductor when soldering or
unsoldering.
– 2 –
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY CHECK-OUT

UNLEADED SOLDER

This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free
mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with the
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to
flow) than ordinary solder so use caution not to let solder
bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and
those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.