Advertisement
Series 19 C20HM2W (on/off) & C20HM2FSW Failsafe Electric
The Series 19 Model C20HM2W (on/off) & C20HM2FSW (Failsafe) electric actuators
features a reversing motor with multi-voltage capabilities; 95vac-265vac (50/60Hz) or 24
Vac/Vdc. An internal heater, and auxiliary switches are standard equipment. Additional
features include a NEMA Type 4X enclosure, manual override, visual mechanical
position indication, LED Indication (Open/Closed) ISO bolt circle, and flying leads. The
auxiliary switches are SPDT and rated for 0.1A @250 Vac, and are factory calibrated.
Failsafe units are capacitor discharge design, and may require up to 15 minutes to
charge when initially provided power.
Additional options are NOT available for these Series 19 Models
Torque
Model
(in/lbs)
C20HM2W
177
C20HM2FSW
177
NOTE: Amp rating is considered Locked Rotor.
Duty cycles are for ambient temperature (73°F)
The Series 19 electric actuator has a sealed cable gland with 2M flying leads. The
electrician is required to make field connections as per the wiring schematic shown in
this manual for the model and voltages listed above. The electrician is responsible for
following all and any, local and/or Agency wiring practices.
Need more information? Download a complete IOM at our website.
File: Series 19 Compack User Manual
Actuator User Manual
Description
Electrical Requirement
95 - 265 Vac
24 Vac/24 Vdc
Amp
Duty
Amp
Draw
Cycle
Draw
0.18
75%
0.96
0.18
75%
0.96
www.asahi-america.com
Rev B
11/3/2022
Cycle Time per 90
Duty
Degrees
Cycle
(Seconds)
10 for dc units
75%
15 for ac units
10 for dc units
75%
15 for ac units
Weight
(Pounds)
1.7
1.7
Page 1 of 4
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Asahi/America 19 Series
Summary of Contents for Asahi/America 19 Series
- Page 1 Series 19 C20HM2W (on/off) & C20HM2FSW Failsafe Electric Actuator User Manual Description The Series 19 Model C20HM2W (on/off) & C20HM2FSW (Failsafe) electric actuators features a reversing motor with multi-voltage capabilities; 95vac-265vac (50/60Hz) or 24 Vac/Vdc. An internal heater, and auxiliary switches are standard equipment. Additional features include a NEMA Type 4X enclosure, manual override, visual mechanical position indication, LED Indication (Open/Closed) ISO bolt circle, and flying leads.
- Page 2 Manual Override Operation This procedure is for both, on/off & Failsafe Units Remove manual override Hex Key from storage position located on the bottom of actuator, which is secured by SS clips. To operate the manual override, insert hex key into hex socket located on top of actuator and rotate to manually cycle valve (CCW to open, CW to close).
- Page 3 Note: Not all wires provided will be used. Heater is internally wired and operational as long as actuator is powered LED Indicator is green open/red closed On/Off Wiring: Need more information? Download a complete IOM at our website. www.asahi-america.com File: Series 19 Compack User Manual Rev B 11/3/2022 Page 3 of 4...
- Page 4 Note: Not all wires provided will be used. Heater is internally wired and operational as long as actuator is powered LED Indicator is green open/red closed Failsafe Wiring: Need more information? Download a complete IOM at our website. www.asahi-america.com File: Series 19 Compack User Manual Rev B 11/3/2022 Page 4 of 4...
Need help?
Do you have a question about the 19 Series and is the answer not in the manual?
Questions and answers