Four-Faith F-G100 Series User Manual
  1. Manuals
  2. Brands
  3. Four-Faith Manuals
  4. Gateway
  5. F-G100 Series
  6. User manual

Four-Faith F-G100 Series User Manual

Smart gateway
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
FOUR FAITH
F-G100 Series Smart Gateway
USER MANUAL
V2.0.1
Xiamen Four-Faith Communication Technology Co., Ltd.

Advertisement

Table of Contents
loading

Related Manuals for Four-Faith F-G100 Series

Summary of Contents for Four-Faith F-G100 Series

  • Page 1 FOUR FAITH F-G100 Series Smart Gateway USER MANUAL V2.0.1 Xiamen Four-Faith Communication Technology Co., Ltd.
  • Page 2 All contents in the files are protected by copyright law, and all copyrights are reserved by Xiamen Four-Faith Communication Technology Co., Ltd. Without written permission, all commercial use of the files from Four-Faith are forbidden, such as copy, distribute, reproduce the files, etc., but non-commercial purpose, downloaded or printed by individual (all files shall be not revised, and the copyright and other proprietorship notice shall be reserved) are welcome.

  • Page 3: Table Of Contents

    Content 1. F-G100 Introduction........................4 1.1 Overview..........................4 1.2 Packing List..........................4 1.3 Panel Introduction.........................5 1.4 LED Status..........................6 1.5 Reset Button.......................... 7 1.6 SIM Card Installation......................7 1.7 Antenna Connection......................8 1.8 Power Cable Connection....................... 8 1.9 Installation..........................8 1.10 Connection For Configuration...................10 3.

  • Page 4: F-G100 Introduction

    1. F-G100 Introduction 1.1 Overview Four-Faith Industrial Gateway F-G100 is an intelligent 3G/4G gateway to provide the necessary M2M applications for all types of terminals. It adopts high-powered industrial 32-bits CPU and is embedded with real time operating system. It supports RS232 (or RS485/RS422), Ethernet and WIFI port that can conveniently and transparently connect the device to a cellular network, allowing you to connect to your existing serial, Ethernet and WIFI devices with only basic configuration.

  • Page 5: Panel Introduction

    1.3 Panel Introduction LAN/ WAN port for Ethernet cable connecction. Insert Ethernet cable to any of 4 LAN ports. RJ45 -1 RJ45-2 Line color White/Orange Orange White/Green Blue White/Blue Green White/Brown Brown RS232/RS485 connection for serial device. Definition Description Input/Output 5V source(1W) Output Power GND, GND for rs232...

  • Page 6: Led Status

    RS485,com1 Input&Output RS485,com2 Input&Output RS485,com2 Input&Output RS485,com3 Input&Output RS485,com3 Input&Output RS485,com4 Input&Output RS485,com4 Input&Output RS485, com5 Input&Output RS485, com5 Input&Output Power interface and IO interface Description Input/Output Digital Output 0 Output Digital Input 1 Input Digital Input 0 Input GND for DI &DO & Relay Input &Output RELAY Relay output...

  • Page 7: Reset Button

    1 means bad signal Online Router has wan IP Router cannot access On doesn’t means internet can access internet WAN port is connected WAN port is not On means blinking /communication connected LAN-1~LAN-4 LAN port is connected LAN port is not On means blinking / communication connected...

  • Page 8: Antenna Connection

    1.7 Antenna Connection Suggest to connect all antennas to get better signal and make router working better, also suggest to place cellular antennas to something icon, such as router box. Must connect ANT-1 for sim card internet. Note: It must to connect ANT-1 if using SIM card internet. 1.8 Power Cable Connection Power cable has two cables, one cable is black with white, this is power pin, need to connect to left of power terminal;...
  • Page 9 DIN Rail: Fixed Plate: Screw specification for installation is M3*5MM countersunk head screws(black).

  • Page 10: Connection For Configuration

    1.10 Connection For Configuration Make PC Ethernet port connect with F-G100 LAN port(any LAN port). Can connect via WIFI if PC doesn’t have Ethernet port. Make PC to get IP automatically from F-G100. Note: May need disable laptop firewall or put configure link 3.

  • Page 11: Setup

    is change password page. Router user name is admin, password is admin by default. Click Change Password button if no need to change; fill the user name and password as you want if need to change password. It needs to fill user name and password next time for login, default user name is admin, password is admin.
  • Page 12 Connection Type Parameter Description Remarks Disable Disable router for internet connection including Static IP Router use wan port for internet access and set wan port with a fixed IP Automatic Router use wan port for internet access and get wan Configuration - DHCP IP automatically Dhcp-4G...
  • Page 13 Wan Nat: Same with Wan Nat under Disable. STP:Same with Wan Nat under Disable. Dhcp-4G User Name: SIM card user name, get from ISP. Password: SIM card password , get from ISP. APN:SIM card APN, get from ISP. Fixed WAN IP: A fixed wan IP if sim car has. Allow those authentication: PAP or CHAP, chosen depends on ISP authentication, usually choose both by default.
  • Page 14 4G->2G Router will communicate with ISP, via 4G auxiliary, then jump to 2G network 3G->4G Router will communicate with ISP, via 3G auxiliary, then jump to 4G network 4G->3G Router will communicate with ISP, via 4G auxiliary, then jump to 3G network EVDO Router can only use EVDO (2g) network Note: Connection type may be different for different model and different module inside.
  • Page 15 Others are same with dhcp-4G. 3G/UMTS/4G/LTE Dail String : a dial number for PPP dail-up, usually *99***1# or *99#. Others are same with dhcp-4G. Optional Settings Router Name: Router name. Host Name/Domain Name: Some ISP will need host name and domain name to identify router, leave as empty for most cases.
  • Page 16 Local IP Address: Router IP, 192.168.4.1 by default. Subnet Mask: Router LAN network sub-net mask, 255.255.255.0 by default. Gateway: Router gateway, 0.0.0.0 means gateway IP will be router IP. Local DNS: Router DNS IP, 0.0.0.0 means router will use DNS from ISP by default. Network Address Server Settings(SHCP) DHCP Type: Parameter...
  • Page 17 DHCP Forwarder DHCP Server：set DHCP server IP, F-G100 will forward DHCP data from/to this server IP. Time Settings NTP Client: enable means router get time from NTP server; disable means router will use router RTC time. Time Zone: Choose time zone. Summer Time(DST):Set summer time or not.

  • Page 18: Ddns

    Save: Click to save changes or settings. Apply Settings: Click to apply changes or settings, changes or settings will work after clicking this button. Cancel Changes: Click to delete changes or settings. Note: Save , Apply Settings and Cancel Changes these three buttons are same function. 3.1.2 DDNS DDNS means dynamic domain name service.
  • Page 19 3.1.3 MAC Address Clone Some ISP need the users to register their MAC address. The users can clone the Router MAC address to their MAC address registered in ISP if they do not want to re-register their MAC address. Clone MAC address can be done for three parts: Clone LAN MAC, Clone WAN MAC, Clone Wireless MAC.
  • Page 20 Choose BGP if need to use RIP2 Router Choose RIP2 Router if need to use RIP OSPF Router Choose OSPF router if need to use OSPF Router Choose Router if another router exists on their network Note: There may be different options for different version. Select set number: 1-50 Route Name: defined routing name by users, up to 25 characters Metric: 0-9999...
  • Page 21 3.1.5 VlANs VLANs function is to divide different VLAN ports by users' will. The system supports 15 VLAN port from VLAN1-VLAN15. However there is only 5 time ports (1 WAN port and 4 LAN port) divided by users themselves,and LAN port and WAN port disable to divide into one VLAN port meanwhile. 3.1.6 Networking Bridging-Create Bridge: creates a new empty network bridge for later use.
  • Page 22 Create steps as below: Click 'Add' to create a new bridge, configuration is as below: Create bridge option: the first br0 means bridge name. STP means to on/off spanning tree protocol. Prio means priority level of STP, the smaller the number, the higher the level. MTU means maximum transfer unit, default is 1500, delete if it is not need.
  • Page 23 Port Setup: Set the port property, the default is not set. Choose not bridge to set the port's own properties, detailed properties are as below: MTU: maximum transfer unit Multicast forwarding: enable or disable multicast forwarding Masquerade/NAT: enable or disable Masquerade/NAT IP Address: set ra0's IP address, and do not conflict with other ports or bridge Subnet Mask: set subnet mask.

  • Page 24: Wireless

    Multiple DHCP Server: using multiple DHCP service. Click 'Add' in multiple DHCP server to add a new DHCP server setting. Can choose port or bridge (do not be configured as eth0), can choose on of off for the service. Start means start IP address. Max means maximum assigned DHCP clients.
  • Page 25 G-only：Only supports the 802.11g standard wireless devices. NG-Mixed：Support 802.11g, 802.11n wireless devices. N-only：Only supports the 802.11g standard wireless devices. Wireless Network Name(SSID): The SSID is the network name shared among all devices in a wireless network. It is case-sensitive and must not exceed 32 alphanumeric characters, which may be any keyboard character.
  • Page 26 3.2.2 Wireless Security Wireless Security wl0 is for 2.4G.
  • Page 27 WEP：Is a basic encryption algorithm is less secure than WPA.Use of WEP is discouraged due to security weaknesses, and one of the WPA modes should be used whenever possible. Only use WEP if you have clients that can only support WEP (usually older, 802.11b-only clients). Authentication Type：Open or shared key。...

  • Page 28: Service

    WPA Enterprise/WPA2 Enterprise/WPA2 Enterprise Mixed: WPA Enterprise uses an external RADIUS server to perform user authentication. WPA Algorithms: AES/TKIP/TPIP+AES. Radius Auth Sever Address：The IP address of the RADIUS server. Radius Auth Server Port：The RADIUS Port (default is 1812)。 Radius Auth Shared Secret：The shared secret from the RADIUS server。 Key Renewal Interva(in seconds): 1-99999。...
  • Page 29 Used domain: users can select here which domain the DHCP clients should get as their local domain. This can be the WAN domain set on the Setup screen or the LAN domain which can be set here. LAN Domain: users can define here their local LAN domain which is used as local domain for DNSmasq and DHCP service if chose above.
  • Page 30 Location: equipment location Contact: contact this equipment management Name: device name RO Community: SNMP RO community name, the default is public, Only to read. RW Community: SNMP RW community name, the default is private, Read-write permissions SSHD Enabling SSHd allows users to access the Linux OS of their Router with an SSH client SSH TCP Forwarding: enable or disable to support the TCP forwarding admin Password Login: allows login with the Router password (username is...
  • Page 31 the password is the Router's password. Note: If users use the Router in an untrusted environment (for example as a public hotspot), it is strongly recommended to use SSHd and deactivate telnet. WAN Traffic Counter Ttraff Daemon: enable or disable wan traffic counter function 3.3.2 USB USB part is used for TF card.

  • Page 32: Vpn

    3.4 VPN Router can be VPN server or VPN client. VPN server needs public IP or special APN sim card, while VPN client can use normal sim card with dynamic IP. 3.4.1 PPTP PPTP Server Broadcast support: enable or disable broadcast support of PPTP server Force MPPE Encryption: enable of disable force MPPE encryption of PPTP data DNS1/DNS2/WINS1/WINS2: set DNS1/DNS2/WINS1/WINS2 Server IP: input IP address of the Router as PPTP server, differ from LAN address...
  • Page 33 Server IP or DNS Name: PPTP server’s IP Address or DNS Name Remote Subnet: the network of the remote PPTP server Remote Subnet Mask: subnet mask of remote PPTP server MPPE Encryption: enable or disable Microsoft Point-to-Point Encryption。 MTU: maximum Transmission Unit MRU: maximum Receive Unit NAT: network Address Translation User Name: user name to login PPTP Server.
  • Page 34 Gateway(L2TP Server): L2TP server’s IP Address or DNS Name Remote Subnet: the network of remote PPTP server Remote Subnet Mask: subnet mask of remote PPTP server MPPE Encryption: enable or disable Microsoft Point-to-Point Encryption MTU: maximum transmission unit MRU: maximum receive unit NAT: network address translation User Name: user name to login L2TP Server Password: password to login L2TP Server...
  • Page 35 Negotiating: this connection launch a request to opposite end, is under negotiating, the connection has not been established yet Establish: the connection has been established, enabled to use this tunnel Action: the action of this connection, current is to delete, edit, reconnect and enable Delete: to delete the connection, also will delete IPSEC if IPSEC has set up Edit: to edit the configure information of this connection, reload this connection to make the configuration effect after edit...
  • Page 36 Enable DPD Detection: enable or disable this function, tick means enable Time Interval: set time interval of connect detection (DPD) Timeout: set the timeout of connect detection Action: set the action of connect detection Advanced Settings: this part contains relevant setting of IKE, ESP, negotiation mode, etc. Enable Advanced Settings: enable to configure 1 and 2 phase information, otherwise it...
  • Page 37 Start Type: WAN UP----start after on-line, System----start when boot up Config via: GUI----Page configuration, Config File----config File configuration Server mode: Router (TUN)-route mode, Bridge (TAP)----bridge mode Router (TUN): Network: network address allowed by OPENVPN server Netmask: netmask allowed by OPENVPN server Bridge (TAP): DHCP-Proxy mode: enable or disable DHCP-Proxy mode Pool start IP: pool start IP of the client allowed by OPENVPN server...
  • Page 38 Use LZO Compression: enable or disable use LZO compression for data transfer Redirect default Gateway: enable or disable redirect default gateway Allow Client to Client: enable or disable allow client to client Allow duplicate cn: enable or disable allow duplicate cn TUN MTU Setting: set the value of TUN MTU TCP MSS: MSS of TCP data TLS Cipher: TLS (Transport Layer Security) encryption standard supports AES-128 SHA and...
  • Page 39 Additional Config: additional configurations of the server CCD-Dir DEFAULT file: other file approaches TLS Auth Key: authority key of Transport Layer Security Certificate Revoke List: configure some revoke certificates OPENVPN Client Server IP/Name: IP address or domain name of OPENVPN server Port: listen port of OPENVPN client Tunnel Device: TUN----Router mode, TAP----Bridge mode Tunnel Protocol: UDP and TCP protocol...
  • Page 40 Use LZO Compression: enable or disable use LZO compression for data transfer NAT: enable or disable NAT through function Bridge TAP to br0: enable or disable bridge TAP to br0 Local IP Address: set IP address of local OPENVPN client TUN MTU Setting: set MTU value of the tunnel TCP MSS: mss of TCP data TLS Cipher: TLS (Transport Layer Security) encryption standard supports AES-128 SHA and...
  • Page 41 GRE (Generic Routing Encapsulation, Generic Routing Encapsulation) protocol is a network layer protocol (such as IP and IPX) data packets are encapsulated, so these encapsulated data packets to another network layer protocol (IP)transmission. GRE Tunnel (tunnel) technology, Layer Two Tunneling Protocol VPN (Virtual Private Network). GRE Tunnel: enable or disable GRE function Number：Switch on/off GRE tunnel app Status：Switch on/off someone GRE tunnel app...

  • Page 42: Security

    3.5 Security You can enable or disable the firewall, filter specific Internet data types,and prevent anonymous Internet requests,ultimately enhance network security. Firewall Protection Firewall enhance network security and use SPI to check the packets into the network.To use firewall protection, choose to enable otherwise disabled. Only enable the SPI firewall, you can use other firewall functions: filtering proxy, block WAN requests, etc.
  • Page 43 box to enable this feature, you can prevent your network from the Ping or detection of other Internet users. so that make More difficult to break into your network. The default state of this feature is enabled ,choose to disable allow anonymous Internet requests. Filter IDENT (Port 113): Enable this feature can prevent port 113 from being scaned from outside.

  • Page 44: Access Restrictions

    Log Level: Set this to the required log level. Set Log Level higher to log more actions. Options: When select Enable, the corresponding connection will be recorded in the journal, the disabled are not recorded. Incoming Log: To see a temporary log of the Router's most recent incoming traffic, click the Incoming Log button.
  • Page 45 Two options in the default policy rules: "Filter" and "reject". If select "Deny”, you will deny specific computers to access any Internet service at a particular time period. If you choose to "filter"，It will block specific computers to access the specific sites at a specific time period. You can set up 10 Internet access policies filtering specific PCs access Internet services at a particular time period.
  • Page 46 set up Internet access policy 1. Select the policy number (1-10) in the drop-down menu. 2. For this policy is enabled, click the radio button next to "Enable" 3. Enter a name in the Policy Name field. 4. Click the Edit List of PCs button. 5.
  • Page 47 11. To create or edit additional policies, repeat steps 1-9. 12. To delete an Internet Access Policy, select the policy number, and click the Delete button. Note: 3.3.3.1 The default factory value of policy rules is "filtered". If the user chooses the default policy rules for "refuse", and editing strategies to save or directly to save the settings.
  • Page 48 receive only with custom Accept only the data packets conform to the following rules: rules of network address, discarded all other URL address. Fill device MAC address as FF:FF:FF:FF:FF:FF, then click Add button. 3.6.4 Packet Filter To block some packets getting Internet access or block some Internet packets getting local network access, you can configure filter items to block these packets.

  • Page 49: Nat

    input: packet from WAN to LAN output: packet from LAN to WAN Protocol: packet protocol type Source Ports: packet's source port Destination Ports: packet's destination port Source IP: packet's source IP address Destination IP: packet's destination IP address Note: "Source Port" ,"Destination Port" ,"Source IP" ,"Destination IP" could not be all empty ,you have to input at least one of these four parameters.
  • Page 50 applications are any applications that use Internet access to perform functions such as videoconferencing or online gaming. When users send this type of request to your network via the Internet, the Router will forward those requests to the appropriate PC. If you only want to forward a single port, see Port Forwarding.

  • Page 51: Qos

    Virtual IP Mapping can do cases for that not show real IP from outside users. Virtual IP: virtual IP will be showed to outside. Real IP: device real IP. Objective IP : destination IP when do virtual IP mapping. Device : choose interface for virtual IP mapping. 3.8 QoS 3.8.1 Basic Bandwidth management prioritizes the traffic on your Router.

  • Page 52: App

    You may specify priority for all traffic from a given IP address or IP Range. Check all values and click Save Settings to save your settings. Click the Cancel changes button to cancel your unsaved changes. 3.9 App 3.9.1 Communication Gateway Communication gateway is to do communication protocol analysis, can support device communication such as PLC.
  • Page 53 PORT PORT is a TCP protocol but with a register packet when it connects to server. Register packet will contain device ID. Fill devices ID and dev phone number(can be any you want), click save and apply settings buttons, then F0G100 will connect to the TCP server, it will send a register packet to server the time F-G100 connects.
  • Page 54 information, gizwits gizwits means F-G100 will connect to gizwits cloud platform(gizwits is a IoT platform in China). Fill needed information correctly (can get information from gizwits IOT platform), click save and apply setting button, then F-G100 will connect to gizwits with filled key, BaiduCloud BaiduCloud means F-G100 will connect to Baidu cloud platform (Baidu Cloud is a IoT platform in China).
  • Page 55 Azure For Azure connection, F-G100 supports use connect string to connect to it. Fill connect string which got from mircosoft, click save and apply settings button, then F-G100 will connect to Azure, MTCP/MRTU Custom F-G100 will connect to server with standard TCP or UDP(depends on tcp or udp is chosen), There will have register packet when F-G100 connects to server, register packet is filled string for Custom registration package;...
  • Page 56 Different COM and LAN can be used at same time with different or same configuration. First, Enable it. Binding Center means com data will send to the chosen data center with configuration server protocol. Can choose 1/2/3/4/5 or ALL, ALL means com data will send to all 5 servers. Disable means no need send to data center.
  • Page 57 First , Enable it. Apply protocol can choose transparent or acquisition mode. Transparent means Ethernet device is transparent transmission; acquisition mode means F-G100 will to read Ethernet device with configuration. For Ethernet PLC/device, need to fill device IP and port usually to make F0G100 to communicate with PLC/device first.
  • Page 58 dev.) Manufacturer means F-G100 can support different Ethernet PLC, such as SIEMENS, MITSUBISHI, Schnedier, none means Ethernet device is not from those manufacturers but has its own protocol. Dev Type is to choose protocol/PLC type for Ethernet device. Then can configure acquisitive parameters for Ethernet port device connected depends on different devices and parameters.

  • Page 59: Admin

    3.10 Admin 3.10.1 Management The Management screen allows you to change the Router's settings. On this page you will find most of the configurable items of the Router code. The new password must not exceed 32 characters in length and must not include any spaces. Enter the new password a second time to confirm it.
  • Page 60 Protocol：This feature allows you to manage the Router using either HTTP protocol or the HTTPS protocol Auto-Refresh：Adjusts the Web GUI automatic refresh interval. 0 disables this feature completely Enable Info Site：Enable or disable the login system information page Info Site Password Protection：Enable or disable the password protection feature of the system information page Remote Access：This feature allows you to manage the Router from a remote location, via the Internet.
  • Page 61 command line or startup scripts to actually use this. Language：Set up the Router page shows the type of language, including simplified Chinese and English. Remote Upgrade: custom-developed remote management server for this station Router monitoring and management, configuration parameters, WIFI advertising updates. 3.10.2 Keep Alive You can schedule regular reboots for the Router : Regularly after xxx seconds.
  • Page 62 Run Command ： You can run command lines via the web interface. Fill the text area with your command and click Run Commands to submit. Startup：You can save some command lines to be executed at startup's Router. Fill the text area with commands (only one command by row) and click Save Startup.

  • Page 63: Status

    2. Click the Browse... button and chose the firmware upgrade file. 3. Click the Upgrade button and wait until the upgrade is finished. Note： Upgrading firmware may take a few minutes. Do not turn off the power or press the reset button! After flashing, reset to：If you want to reset the Router to the default settings for the firmware version you are upgrading to, click the Firmware Defaults option.
  • Page 64 MAC Address: MAC address of WAN, settingClone MAC Address to modify Host Name: host name of the Router, settingbasic setting to modify WAN Domain Name: domain name of WAN, settingbasic setting to modify LAN Domain Name: domain name of LAN, unavailable to modify Current Time: local time of the system Uptime: operating uptime as long as the system is powered on Total Available: the room for total available of RAM (that is physical memory minus some reserve...
  • Page 65 Active IP Connections: total active IP connections Protocol: connection protocol Timeouts: connection timeouts, unit is second Source Address: source IP address Remote Address: remote IP address Service Name: connecting service port Status: displayed status Total Available: the room for total available of RAM (that is physical memory minus some reserve and the kernel of binary code bytes) Free: free memory, the Router will reboot if the memory is less than 500kB Used: used memory, total available memory minus free memory...
  • Page 66 Active: active use of buffer or cache memory page file size Inactive: not often used in a buffer or cache memory page file size IP Filter Maximum Ports: preset is 4096, available to re-management Active IP Connections: real time monitor active IP connections of the system, click to see the table as blow: Active IP Connections: total active IP connections Protocol: connection protocol...
  • Page 67 IP Address: IP address of Router WAN Subnet Mask: subnet mask of Router WAN Gateway: the gateway of Router WAN DNS1, DNS2, DNS3: DNS1/DNS2/DNS3 of Router WAN Remaining Lease Time: remaining lease time of IP address in DHCP way DHCP Release: release DHCP address DHCP Renew: renew IP address in DHCP way, default is 1 day Login Status: connection status of WAN Disconnection: disconnect...
  • Page 68 Total Flow: flow from power-off last time until now statistics, download and upload direction Monthly Flow: the flow of a month, unit is MB Last Month: the flow of last month Next Month: the flow of next month Backup: backup data administration Restore: restore data administration Delete: delete data administration 3.11.3 LAN...
  • Page 69 MAC Address: MAC Address of the LAN port ethernet IP Address: IP Address of the LAN port Subnet Mask: Subnet Mask of the LAN port Gateway: Gateway of the LAN port Local DNS: DNS of the LAN port Host Name: host name of LAN client IP Address: IP address of the client MAC Address: MAC address of the client Conn.
  • Page 70 User Name: user name of PPPoE client Local IP: IP address assigned by PPPoE client Delete: click to delete PPPoE client Interface: the interface assigned by dial-up system Local IP: tunnel IP address of local L2TP Remote IP: tunnel IP address of L2TP server Delete: click to disconnect L2TP Interface: the interface assigned by dial-up system User Name: user name of the client...
  • Page 71 Received (RX): received data packet Transmitted (TX): transmitted data packet MAC Address: MAC address of wireless client Interface: interface of wireless client Uptime: connecting uptime of wireless client TX Rate: transmit rate of wireless client RX Rate: receive rate of wireless client Signal: the signal of wireless client Noise: the noise of wireless client SNR: the signal to noise ratio of wireless client...
  • Page 72 Active Time: connection time to management. 3.11.6 Bandwidth Bandwidth Monitoring-LAN Graph abscissa axis: time vertical axis: speed rate Bandwidth Monitoring-WAN Graph abscissa axis: time vertical axis: speed rate...
  • Page 73 Bandwidth Monitoring-Wireless (W10) Graph abscissa axis: time vertical axis: speed rate 3.11.7 Sys-Info Router Name: the name of the Router Router Model: the model of the Router LAN MAC: MAC address of LAN port WAN MAC: MAC address of WAN port Wireless MAC: MAC address of the wireless WAN IP: IP address of WAN port LAN IP: IP address of LAN port...
  • Page 74 Radio: display whether radio is on or not Mode: wireless mode Network: wireless network mode SSID: wireless network name Channel: wireless network channel TX Power: reflection power of wireless network Rate: reflection rate of wireless network Received (RX): received data packet Transmitted (TX): transmitted data packet DHCP Server: enabled or disabled ff-radauth: enabled or disabled...
  • Page 75 Total Available: the room for total available of RAM (that is physical memory minus some reserve and the kernel of binary code bytes) Free: free memory, the Router will reboot if the memory is less than 500kB Used: used memory, total available memory minus free memory Buffers: used memory for buffers, total available memory minus allocated memory Cached: the memory used by high-speed cache memory Active: Active use of buffer or cache memory page file size...

Table of Contents