Sony XAV-AX100 Service Manual page 5

MODEL IDENTIFICATION
The XAV-AX100 and XAV-AX100C2 can not be identifi ed by the
model name printed on the front panel top.
Be sure to refer to the model number label affi xed to the bottom
of the main unit.
XAV-AX100
Model number label
XAV-AX100
or
XAV-AX100C2
When identifying the destination of the XAV-AX100 or XAV-
AX100C2, refer to the shape, model name, Part No., serial number,
etc. of the model number label affi xed to the bottom of the main
unit.
XAV-AX100 (US, CND, AEP, UK)
XAV-AX100 (E, AUS)
XAV-AX100 (IND, IND3)
Check the Serial No. to distinguish IND and IND3.
XAV-AX100
Serial No.
IND : 71xxxxx
IND3 : 77xxxxx
Note : "xxxxx" of the Serial No. are
4-686-131-0[]
XAV-AX100C2 (E)
XAV-AX100C2
4-739-664-0[]
NOTE FOR CABLE FOR AUTOMOBILE (RC-SR1) OF
IND MODEL
The CABLE FOR AUTOMOBILE (RC-SR1) (Cable for steer-
ing wheel remote input) has been added to AX100: IND model in
the midway of production and the operating instruction has been
changed accordingly.
Check the Serial No. about whether CABLE FOR AUTOMOBILE
(RC-SR1) is supplied or not.
Serial No. 7104600 or smaller:
CABLE FOR AUTOMOBILE (RC-SR1) is not supplied
Serial No. 7104601 or larger:
CABLE FOR AUTOMOBILE (RC-SR1) is supplied
XAV-AX100
or
XAV-AX100C2
XAV-AX100
4-686-128-0[]:
XAV-AX100 (US, CND)
4-686-130-0[]:
XAV-AX100 (AEP, UK)
XAV-AX100
4-686-129-0[]:
XAV-AX100 (E, AUS)
numeric characters.
Distinguish IND and IND3
models with the first two digits.
DESTINATION SETTING METHOD
(Except AX100: IND3 model)
When the MAIN board or U310 on the MAIN board is replaced,
the destination setting is necessary.
Note 1: Remote commander is necessary.
It is necessary to operate by the remote commander, even in case of
models that have not been supplied the remote commander.
(Refer to "7. ELECTRICAL PARTS LIST" on page 61 about the
remote commander)
Note 2: When discriminating the destination, refer to "MODEL IDENTI-
FICATION" on the left.
Note 3: It is not necessary to perform the destination setting work in
AX100: IND3 model.
1. Destination Setting
Set destination according to the procedure below.
1-1. Setting the Destination Code
1. Turn the power on this unit.
2. Press the [HOME] button on the main unit.
3. In the state of source off (Home screen is displayed), enter the
destination setting mode by pressing the buttons on the remote
commander in order of the [4] t [5] t [6] (press only the [6]
button for two seconds).
Screen display
4. The following screen is displayed and the destination setting
mode becomes effective.
Note: Refer to the following "1-2. Entering the Destination Code" for op-
eration method.
Screen display
<DESTINATION SETTING MODE>
0 0 0 0
EUR:*00000
E:*00003
FT(JPN):*00007
(Displayed characters/values in the following fi gure are ex-
ample)
5. The resetting operation is executed by pressing the reset button
after the setting ends, and the unit returns to the normal condi-
tion.
XAV-AX100/AX100C2
Ver. 1.3
0 1
UC:*00001
IN:*00015
– Continued on next page –
5
SYS SET