Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Silver King SKDL18-EDUS4
Summary of Contents for Silver King SKDL18-EDUS4
- Page 1 Technical Manual Replacement Parts List Refrigerated Salad Dispenser MODEL: SKDL18-EDUS4 Marmon Foodservice Technologies 355 Kehoe Blvd., Carol Stream, IL 60188 Contact: (800) 328-3329 Silverking.com FORM NO. 47278-SK REV A 07/2022 Specifications Subject to Change Without Notice.
- Page 2 INSPECT FOR DAMAGE AND UNCRATE Upon delivery of your new Silver King unit, uncrate at once to examine and test for possible damage following the instructions printed on the exterior of the container. Report any damages to the carrier responsible for transportation and promptly present a claim for any evidence of mishandling.
-
Page 3: Different Types Of Alerts
Risk of fire or explosion. Flammable refrigerant used. Consult repair manual/owner’s guide before attempting to service this product. All safety precautions must be followed. Caution – Risk of fire or explosion. To be repaired only by trained service personnel. Use only Silver King approved replacement parts. Flammable refrigerant used. Caution –... - Page 4 SAFETY PRECAUTIONS (Continued): WARNING - Do not use electrical appliances inside the food/ice storage compartments unless they are of the type recommended by the manufacturer. WARNING - Appliances and their surroundings shall not attain excessive temperatures in normal use. WARNING - Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
-
Page 5: Installation
At no time should the drawers be extended and used as a platform for standing on to reach elevated equipment. Energy Rating Your Silver King refrigerator has a class 5 energy rating. The refrigerator was tested at an ambient temperature of 40°C at 40% relative humidity. -
Page 6: Work Procedure
R290 R PECIALIZED RECAUTIONS AND UIDELINES FOR ERVICING NITS SING EFRIGERANT: Qualification of Service Personnel/Workers: Required qualification of working personnel for maintenance, service and repair operations. Every working procedure that affects safety means shall only be carried out by competent persons. Examples for such working procedures are: ·... - Page 7 Checks to the Refrigeration Equipment: Where electrical components are being changed, they shall be fit for the purpose and to the correct specification. At all times the manufacturer’s maintenance and service guidelines shall be followed. If in doubt, consult the manufacturer’s technical department for assistance.
- Page 8 Cabling: Check that cabling will not be subject to wear, corrosion, excessive pressure, vibration, sharp edges or any other adverse physical or environmental effects. The check shall also take into account the effects of aging or continual vibration from sources such as compressors or fans.
-
Page 9: Charging Procedures
Charging Procedures: In addition to conventional charging procedures, the following requirements shall be followed. WARNING: Ensure that contamination of different refrigerants does not occur when using charging equipment. Hoses or lines shall be as short as possible to minimize the amount of refrigerant contained in them. WARNING: Cylinders shall be kept in an appropriate position according to the instructions. -
Page 10: Operation
Electrical Connections Be sure to check the data plate, located on the liner of the cabinet, for required voltage prior to connecting the unit to a power source. The specifications on the data plate supersede any future discussion. The standard unit is equipped with an eight (8) foot power cord that requires a 115 Volt, 60 Cycle, 1 Phase properly grounded electrical receptacle. - Page 12 REPLACEMENT PARTS LIST - SKDL18-EDUS1 ITEM NO. PART DESCRIPTION PART NO. SCOOP HOLDER 38666-SK SCREW SHOULDER 99971 DRAWER ASSEMBLY COMPLETE 39293 KIT DRAWER GASKET 10310-84 DRAWER SLIDE CENTER RH DRAWER SLIDE CENTER LH 10451-05 KIT (1 DRAWER) CABINET SLIDE RH CABINET SLIDE LH FRONT COVER (WITHOUT KNOB) 38551...
- Page 14 Thermistor Field Testing Use the guide below to test if a thermistor (temperature probe) is functioning properly. See the replacement parts list for part number information. Table 2 is valid for all thermistors listed on table 1. • Establish Thermistor Temperature Table 2 ▪...
- Page 15 90 DAY REPLACEMENT PARTS WARRANTY Silver King warrants to the original Equipment purchaser that a replacement OEM part thereof will be free of defects in material and workmanship, under normal use and service, for a period of 90 days from the date of original purchase of such replacement OEM part subject to all terms and conditions herein.
- Page 16 Silver King’s review to be inefficient or inoperative due to defects in material or factory workmanship.
-
Page 17: Product Ordering Information
An RMA (Returned Merchandise Authorization) form must be completed and then approved by Silver King. Please contact Silver King for details. Restocking fee will apply. All electrical equipment is single phase. Prices, designs, and specifications are subject to change without notice.