Table of Contents
Advertisement
Specifications
Recording method
3-color exposure with OLED
Film used
FUJIFILM INSTAX WIDE instant film (sold
separately)
Number of images
10 images/film pack
Image size
62 mm × 99 mm/2.4 in. × 3.9 in.
Supported image
800 × 1260 dots
size
Printing resolution
12.5 dots/mm (318 dpi, 80 μm dot pitch)
Printing levels
256 levels per color (RGB)
Interface
Standard compliance: Bluetooth Ver. 4.2
(BLE)
Supported image
JPEG, PNG, HEIF, DNG
format
Printing time
Image recording - photo output (fed out):
Approximately 12 sec.
Approximate
Approximately 100 prints (from full
printing capacity
charge)
* The number of prints depends on the
usage conditions.
Power supply
Lithium ion battery (internal type: not
removable)
Charging time
Approximately 80 to 120 minutes
(Charging time depends on the
temperature and battery remaining level)
Power consumption
Approximately 3 W
Operating
Temperature: +5ºC to +40ºC (+41ºF to
environment
+104ºF)
Humidity: 20% to 80% (no condensation)
Main unit
139 mm × 127.5 mm × 33.7 mm/5.5 in. ×
dimensions
5 in. × 1.3 in.(excluding projecting parts)
Main unit weight
Approximately 340 g/12 oz (excluding
film pack)
Supplied
Micro USB cable (BOD700-101, Length:
accessories
30 cm/11.8 in.)
Stand (1)
Strap (1)
*The above specifications are subject to change.
10
Troubleshooting
Please check the following items before considering a problem to
be a malfunction. If the problem persists even after taking action,
please contact the Fujifilm service center for repair in your country
or visit the website below.
Fujifilm website: http://www.fujifilm.com/
If the following problem occurs���
Problem
Possible causes and solutions
I cannot turn on
• The battery may not be charged. Please
the printer.
charge the printer.
• You did not press the Power button long
enough. Press and hold the Power button
for approximately 1 second.
The battery
If you use the printer in a very cold
loses its charge
environment, the battery will drain quickly.
quickly.
Please keep the printer warm before
printing.
The power cut
The battery level may be low. Please charge
off during use.
the printer.
Charging does
Make sure that the USB power adapter plug
not start.
is properly connected to the power outlet.
It takes too long
At low temperatures, charging may take
to charge.
some time.
Charging stops
Charge the battery in a temperature range of
during charging.
5°C to 40°C (41°F to 104°F). If you cannot
charge the printer in this range, contact your
FUJIFILM dealer or support center.
The printer does
• There may be a temporary malfunction.
not work
Please press the reset button. If it still does
properly.
not work properly, please contact our
repair service center for repair.
• The battery may not be charged. Please
charge the printer.
The film pack
• Please use FUJIFILM INSTAX WIDE instant
does not load or
print film only (INSTAX SQUARE or INSTAX
does not load
MINI instant print film cannot be used).
smoothly.
• Align the yellow mark on the film pack
with the printer alignment mark (yellow)
and load it.
The film does
• The film may be misaligned due to shock
not unload.
such as vibration or dropping. Please load
a new film pack.
• If the film is jammed, turn the printer off
and turn it on again. If the problem
persists, remove the jammed film and
then load a new film pack.
Some or all of
Do not open the film door until the film is
the finished
used up. If the film door is opened with film
prints are white.
remaining, the film is exposed and the
exposed area becomes white.
The print is
• Do not shake, bend, fold or hold the print
uneven.
immediately after it is printed.
• Do not obstruct the film ejection slot.
Advertisement
Table of Contents
