Table of Contents
Advertisement
The RBRC seal
The RBRC seal on the nickel-metal
hydride battery indicates that VTech
Communications, Inc. is voluntarily
participating in an industry program to
collect and recycle these batteries at the
end of their useful lives, when taken out
of service within the United States and
Canada.
The program provides a convenient
alternative to placing used nickel-metal
hydride batteries into the trash or
municipal waste, which may be illegal in
your area.
VTech's participation makes it easy for
you to drop off the spent battery at local
retailers participating in the program
or at authorized VTech product service
centers. Please call 1 (800) 8 BATTERY
information on Ni-MH battery recycling
and disposal bans/restrictions in your
area. VTech's involvement in this program
is part of its commitment to protecting
our environment and conserving natural
resources.
The RBRC seal and 1 (800) 8 BATTERY
are the registered trademarks of
Call2recycle, Inc.
FCC, ACTA and IC regulations
FCC Part 15
NOTE: This equipment has been
tested and found to comply with
the requirements for a Class B digital
device under Part 15 of the Federal
Communications Commission (FCC) rules.
These requirements are intended to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency
energy and, if not installed and used
in accordance with the instructions,
may cause harmful interference to
radio communications. However, there
is no guarantee that interference will
not occur in a particular installation.
If this equipment does cause harmful
®
for
interference to radio or television
reception, which can be determined
by turning the equipment off and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
• Reorient or relocate the receiving
®
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet
on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
WARNING: Changes or modifications to
this equipment not expressly approved
by the party responsible for compliance
could void the user's authority to operate
the equipment.
This device complies with Part 15 of the
FCC rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference,
28
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation. Privacy of communications
may not be ensured when using this
telephone.
To ensure safety of users, the FCC has
established criteria for the amount of
radio frequency energy that can be
safely absorbed by a user or bystander
according to the intended usage of the
product. This product has been tested
and found to comply with the FCC
criteria. The handset may be safely held
against the ear of the user. The telephone
base shall be installed and used such
that parts of the user's body other than
the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies
with Canadian requirement:
CAN ICES-3 (B)/NMB-3(B)
FCC Part 68 and ACTA
This equipment complies with Part
68 of the FCC rules and with technical
requirements adopted by the
Administrative Council for Terminal
Attachments (ACTA). The label on the back
or bottom of this equipment contains,
among other things, a product identifier
in the format US:AAAEQ##TXXXX. This
identifier must be provided to your
telephone service provider upon request.
The plug and jack used to connect this
equipment to premises wiring and the
telephone network must comply with
applicable Part 68 rules and technical
requirements adopted by ACTA. A
compliant telephone cord and modular
plug is provided with this product.
It is designed to be connected to a
compatible modular jack that is also
compliant. An RJ11 jack should normally
be used for connecting to a single line
and an RJ14 jack for two lines. See the
installation instructions in the user's
manual.
The Ringer Equivalence Number (REN) is
used to determine how many devices you
may connect to your telephone line and
still have them ring when you are called.
The REN for this product is encoded as
the 6th and 7th characters following the
US: in the product identifier (e.g., if ##
is 03, the REN is 0.3). In most, but not all
areas, the sum of all RENs should be five
(5.0) or less. For more information, please
contact your telephone service provider.
This equipment must not be used with
Party Lines. If you have specially wired
alarm dialing equipment connected
to your telephone line, ensure the
connection of this equipment does not
disable your alarm equipment. If you
have questions about what will disable
alarm equipment, consult your telephone
service provider or a qualified installer.
If this equipment is malfunctioning, it
must be unplugged from the modular
jack until the problem has been
corrected. Replacement to this telephone
equipment can only be made by the
manufacturer or its authorized agents.
For replacement procedures, follow the
instructions outlined under the Limited
warranty.
If this equipment is causing harm to
the telephone network, the telephone
service provider may temporarily
discontinue your telephone service. The
telephone service provider is required
to notify you before interrupting service.
If advance notice is not practical, you
will be notified as soon as possible. You
will be given the opportunity to correct
the problem and the telephone service
provider is required to inform you of your
right to file a complaint with the FCC.
Your telephone service provider may
make changes in its facilities, equipment,
operation, or procedures that could
29
Advertisement
Table of Contents
