VTech CS6719 User Manual page 19

I cannot dial Make sure there is a dial
out. tone before dialing. It
is normal if the handset
takes a second or two
to synchronize with the
telephone base before
producing a dial tone. Wait
an extra second before
dialing.
Eliminate any background
noise. Mute the handset
before dialing, or dial from
another room in your home
with less background
noise.
The display The handset is
deregistered from the
shows To
telephone base.
register
HS... and
Place the handset in the
...see manual
telephone base to register
alternately.
it back. The handset shows
The handset
Registered and you hear a
does not work
beep when the registration
at all.
process completes. This
process takes about 90
seconds to complete.
The display Place the handset in the
shows Low telephone base or charger
battery. for charging.
The battery Make sure the handset is
does not placed in the telephone
charge in the base or charger correctly.
handset or
If the battery is completely
the handset
depleted, charge the
battery does
battery for at least 30
not accept
minutes before use.
charge.
You may need to purchase
a new battery.
The telephone Make sure the ringer volume
does not ring is not set to off.
when there is
The handset may be too
an incoming
far from the telephone
call.
base. Move it closer to the
telephone base.
My handset Move the handset closer to
beeps the telephone base. It may
and is not be out of range.
performing
normally.
I hear other Disconnect the telephone
calls when base from the telephone
using the wall jack. Plug in a different
telephone. telephone. If you still hear
other calls, the problem is
probably in the wiring or
telephone service. Contact
your telephone service
provider.
I hear noise on Make sure the telephone
the cordless line cord is plugged in
handset and securely.
the keys do
not work.
There is The handset may be out of
interference range. Move it closer to the
during a telephone base.
telephone
If you subscribe to high-
conversation.
speed Internet service (DSL
My calls fade
- digital subscriber line)
out when
through your telephone
I am using
line, you must install a
the cordless
DSL filter between the
handset.
telephone line cord and
the telephone wall jack.
The filter prevents noise
and caller ID problems
caused by DSL interference.
Contact your DSL service
provider for more
information about DSL
filters.
Appliances or other
cordless telephones
plugged into the same
circuit as the telephone
base can cause
interference. Try moving
the appliance or telephone
base to another outlet.
The location of your
telephone base can
impact the performance
of your cordless phone.
For better reception, install
the telephone base in a
centralized location within
your home or office,
away from walls or other
obstructions. In many
environments, elevating the
telephone base improves
overall performance.
26
The telephone Caller ID is a subscription
does not service. You must subscribe
receive caller to this service from your
ID or the telephone service provider
telephone for this feature to work on
does not your telephone.
show caller
Both your and the caller's
ID during call
telephone service
waiting.
providers must use
equipment compatible
with the caller ID service.
The caller may not be
calling from an area which
supports caller ID.
The caller ID information
displays after the first or
second ring.
The display The handset may be out of
shows Out of range. Move it closer to the
range or no telephone base.
pwr at base.
Make sure the power cord
is securely plugged into
the telephone base. Use
a working electrical outlet
not controlled by a wall
switch.
I subscribe to a Make sure your computer
nontraditional is powered on, and
telephone your Internet is working
service that properly.
uses my
Make sure to plug your
computer
USB telephone adapter
to establish
into a dedicated USB port
connections,
on your computer. Do not
and my
plug into a multiple port
telephone
USB hub (USB splitter) that
doesn't work.
is not powered.
In a few rare instances, the
USB port on your computer
may not have enough
power. In these instances,
try using a USB hub with
its own external power
supply.
If you are using a firewall, it
may prevent access to your
nontraditional telephone
service. Contact your
service provider for more
information.
I accidentally While the handset is not
set my LCD in use or is on a call, press
language to MENU and then enter
Spanish or 364# to change the
French, and handset LCD language
I don't know back to English.
how to change
it back to
English.
27