Advertisement
Quick Links
Preview all steps before beginning. Should any portion of these instructions be unclear, contact a qualified contractor, handyman or call
us direct at 1-800-582-9595 for assistance. Do not attempt to install this Vantage Point Product if you have any doubts as to its proper
installation. CAUTION- This shelf system is intended for use only with maximum weight indicated. Use with heavier than the maximum
weights indicated may result in instability causing possible injury. Use of this product for any other purpose unless specified by Vantage
Point Products is not recommended. Think safety first!
Δ INDICATES TO NOTE CAUTION WHICH IF NEGLECTED MAY RESULT IN AN IMPROPER OR UNSTABLE ASSEMBLY.
FIG.
ITEM
DESCRIPTION
A
Wall Plate
Steel wall plate with tab
B
Large Washer
1/4" uss flat washer
C
Lag Screw
5/16" x 3" hex head lag screw
D
Pin Ring
Plastic pin ring
E
Retaining Pin
5/16" dia x 1-5/16" steel pin
F
Support Tube (Upper) 18"support tube with channel with
5/16" thru hole
G
Tube Coupler Sleeve
6" coupler sleeve
H
Support Tube (Lower) 18"support tube with channel with
small pan head screw hole
I
Flat Head Screw
#8-32 x 3/8" flat head screw
J
Flange Nut
#8-32 serrated flange nut
K
Plastic Wall Plate Cover plastic wall plate cover
L
Slide Plate
3" steel slide plate
M
Shelf Bracket
steel shelf bracket
N
Hold Down Plate
steel hold down plate (w/ bumpers)
O
Allen Screw
#1/4-20 x 7/8" button head allen screw
P
Hex Nut
#1/4-20 hex jam nut
Q
Glass Shelf
15" deep x 17" wide tempered
glass shelf
R
Wire Management
6" plastic snap-in cover
S
Allen Wrench
5/32" allen wrench
T
Allen Screw
#1/4-20 x 3/8" button head allen screw
U
Rubber Bumper
rubber bumper
(installed at factory)
Maximum Weight Ratings
3 Glass Shelves 75 lbs. Total
(Maximum a glass shelf will hold is 25 lbs.)
Total Shelf System Rating 100 lbs. with the single unit/shelf kit bracket used.
QTY
A
2
6
6
1
1
1
C
D
1
1
E
4
4
2
3
3
3
6
6
J
3
3
1
6
O
18
L
K
Sistema de anaqueles para componentes
R
M
Q
Modelo AXWG03
Advertisement
Related Manuals for Vantage Point Products AXWG03
Summary of Contents for Vantage Point Products AXWG03
- Page 1 Sistema de anaqueles para componentes Modelo AXWG03 Preview all steps before beginning. Should any portion of these instructions be unclear, contact a qualified contractor, handyman or call us direct at 1-800-582-9595 for assistance. Do not attempt to install this Vantage Point Product if you have any doubts as to its proper installation.
- Page 2 Once you have confirmed your shelf mounting position; start by marking your Step 1 Installation of your shelf system requires 36” of vertical wall space. Step 4 wall plate mounting hole positions. Using the diagram at left you can position Locate the best mounting position for your system, Suggestions: Avoid foot traf- your mounting holes easily and accurately.
- Page 3 Install the LOWER wall plate (A) using the remaining three large flat washers FIG 1: Install plastic wall plate covers (K) on top and bottom of support tube/ Step 7 Step 10 (B) and lag screws (C). Position lower wall plate as pictured at left. Using a 1/2” bracket assembly.
- Page 4 Install the glass hold down plate (N) by inserting the allen screw (O) though the FIG 1: Use wire management covers (R) on back of wall system support tube. Step 14 Step 12 glass hold down plate (N) and the shelf bracket (M) and threading the 1/4-20 Feed wiring into channel and lock into place by snapping management covers hex nut (P) onto the threaded end of the allen screw (O).