Related Manuals for SUMERAIN S3233XW-B
Summary of Contents for SUMERAIN S3233XW-B
- Page 1 MODEL: S3233XW-B Version: 1.0 INSTALLATION GUIDE TUB AND SHOWER FAUCET MODEL FINISH S3233CW-B CHROME S3233NW-B BRUSHED NICKEL S3233OW-B OIL RUBBER BRONZE S3233BGW-B Brushed Gold SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 2: Before Proceeding
THANK YOU Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions. -
Page 3: Limited Lifetime Consumer Warranty
This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance. - Page 4 1.8 GPM Showerhead Flow rate 5.5GPM @100PSI Spout Max Flow rate SUS304 Stainless steel Spout Material 7-7/8’’ Spout Reach 3-5/32’’ Spout width 10.58lbs Net Weight 11.90lbs Gross Weight 19-11/16”x13-9/16’’x5-5/16’’ Packing box [L x W x H] SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 5 DIMENSION FRONT VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 6 SIDE VIEW OF SHOWER SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 7: Installation Steps
1 PCS 3233032 Set screw 2 PCS 3233033 Anchor 4 PCS 3233034 Mounting screw 4 PCS 3233035 Shower hose 1 PCS If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM... - Page 8 5. Rough-in Valve Installation 5.1 Make a mounting rack (normally use woods as materials) for preparing install the rough-in valve assembly .the mounting board’s face should be Min1-25/32’’ and Max 2-3/4" behind the finish wall surface. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 9 3~5 minutes to flush out dirt and debris. Shut off the water supply again after finish. HOT WATER SUPPLY COLD WATER SUPPLY Locate and level the valve assembly with air level. Mark the mounting hole of rough-in valve on mounting rack. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 10 We take copper tubing as example: 5.4.1(a) Remove the cartridge and check-in valve and reducing valve from valve body before soldering. 5.4.2(a) Soldering the copper tubing to valve body’s hot water and cold water inlet and top shower outlet. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 11 SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 12 5.4.4(a) Reassemble the rough-in valve. 5.4.5 Locate and level the valve assembly and secure to the mounting bracket with screws and anchor. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 13 Please align the elbow front face with the finish wall. Improper elbow installation depth will lead to leak from connector or has to customize extension parts with extra expense. 5.4.7 Rough-in valve installed finished. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 14 After flushing reinstall the cover. Set the pressure reducing valve to full open. Note: With a flat head screwdriver, adjust stem clockwise to close and anticlockwise to open. Please shut off your hot and cold water supply again after test. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 15 SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 16 We recommend the following set maximum mixed water outlet temperatures for use in all premises: 111.2°F [44°C] - for bath fill but see notes below. 105.8°F[41°C] - for showers. 105.8°F[41°C ]- for washbasins. 100.4°F[38°C] - for bidets. The mixed water temperatures must never exceed 114.8°F[46°C] at terminal fitting. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 17 6.6 Attach the temperature limit ring to cartridge for locking the maximum temperature. Reinstall the escutcheon to the bonnet too 6.7 Attach the escutcheon over the valve body. 6.8 Seal the wall around the escutcheon with waterproof sealant. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 18: Showerhead Installation
7.1 Attach Shower arm escutcheon to the shower arm and apply Teflon tape on the thread of shower arm, Secure the shower arm into the pipe elbow inside the wall by rotating clockwise. Standard connect thread of Shower arm inlet: NPT1/2 (US, CA) SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM... - Page 19 7.2 Seal the wall around the shower arm escutcheon with waterproof sealant 7.3 Put the screen washer into the connector of showerhead and secure the showerhead on the shower head arm by hand rotating clockwise. Missing the screen washer might lead to shower invalid. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 20 8.1 Loose the set screws by Allen key and remove the spout nipple assembly from tub spout assembly. 8.3 Apply Teflon tape on the thread of spout nipple supply and screw the thread into the pipe elbow inside the wall. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 21 8.5. Docking the tub spout to the spout nipple supply. 8.6 Secure the spout with set screw by Allen Key. 8.7 Install finish. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
- Page 22 9.1 Apply Teflon tape on the thread of nipple and screw the thread into the pipe elbow inside the wall. 9.2 Dock the shower holder assembly to nipple. 9.3 Secure shower holder to nipple with set screw by Allen Key. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
-
Page 23: Function Inspection
10.1 Turn on hot and cold water supply and check all connections for ensuring no leaking anywhere. 11. FUNCTION INSPECTION 11.1 Turn on the handle, the water outflow from the showerhead. 11.2 Switch the diverter knob, the water will rush from the hand shower. INSTALL FINISH SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM... - Page 24 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG...
Need help?
Do you have a question about the S3233XW-B and is the answer not in the manual?
Questions and answers