U-Line H-6731 Getting Started
U-Line H-6731 Getting Started

U-Line H-6731 Getting Started

Fire rated standard safe
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

H-6731
FIRE RATED
STANDARD SAFE
TOOLS NEEDED
Drill
Flathead Screwdriver
HARDWARE INCLUDED
50 mm Lag
Washer x 4
Screw x 4
GETTING STARTED
1.
When you first receive the safe, open the door with
the key in order to install the batteries. Batteries are
included, located inside the safe.
2. To open door, first remove lock cover from front of
faceplate using a flathead screwdriver, as shown
below. Insert key and turn counterclockwise. Hold
key in the open position and turn knob to the right to
open the door.
NOTE: This key has also been provided in case
you lose or forget your security code or if the
batteries run low. If you lose the key, you'll
need to reference the serial number located
under the removable lock cover to get a
replacement. Contact Uline Customer Service
for additional assistance.
3. Locate batteries inside safe. Open battery
compartment on the back of the door by pushing
the tab. Install the batteries.
PAGE 1 OF 9
1-800-295-5510
uline.com
10 mm Wrench
3/8" Drill Bit
40 mm Plastic
Anchor x 4
USAGE
Lock Cover
3/16" Drill Bit
NOTE: The reset button located on the inside
of the door is covered with a removable cap.
When you use the reset button while setting
combination, remove cap to access button.
Use a pen tip to push the reset button. Replace
the cap securely over the reset button after
setting combination. Failure to do so will
compromise the safety and security of the safe.
ENTERING SECURITY CODE
To enter security code, follow the steps listed below:
1. After installing the batteries, locate the reset button
on the back of the door.
2. Press the reset button with a pen tip and release it;
you will hear a beep. DO NOT SHUT THE DOOR UNTIL
YOU HAVE CONFIRMED THAT YOUR NEW SECURITY
CODE HAS BEEN ENTERED CORRECTLY.
3. With the door open, enter security code, which can
be three to eight digits long, and confirm code by
pressing the
key on the electronic touch pad.
You will have three seconds to press the
otherwise you will have to start over from step one.
There will be two beeps (if the sound is turned on)
and the green light will flash twice if code has been
entered successfully. Before closing door, enter the
new security code. Press the
the lock releases the knob so that you can turn it
and retract the live-action locking bolts.
Para Español, vea páginas 4-6.
Pour le français, consulter les pages 7-9.
key,
key to make sure
0721 IH-6731

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the H-6731 and is the answer not in the manual?

Questions and answers

Summary of Contents for U-Line H-6731

  • Page 1 Para Español, vea páginas 4-6. Pour le français, consulter les pages 7-9. H-6731 1-800-295-5510 uline.com FIRE RATED STANDARD SAFE TOOLS NEEDED Drill Flathead Screwdriver 10 mm Wrench 3/8" Drill Bit 3/16" Drill Bit HARDWARE INCLUDED 50 mm Lag Washer x 4...
  • Page 2: Battery Replacement

    USAGE CONTINUED BATTERY REPLACEMENT 4. If the code fails, go through steps one to three again. If the code works successfully, lock the safe. NOTE: Do not mix old and new batteries. Do 5. When you open the safe in the future, enter the not mix alkaline, standard or rechargeable security code, followed by the key, and turn the...
  • Page 3 USAGE CONTINUED Secure the safe to a wall stud and to a permanent shelf or floor using the predrilled mounting holes in the safe. NOTE: The safe must be secured to a wall stud on one side of the safe in the top and bottom holes in the back of the safe so that it is anchored to the wall stud in two locations.
  • Page 4 H-6731 800-295-5510 uline.mx CAJA FUERTE ESTÁNDAR EVALUADA CONTRA FUEGO HERRAMIENTAS NECESARIAS Taladro Desarmador Plano Llave de 10 mm Broca de 3/8" Broca de 3/16" TORNILLERÍA INCLUIDA 4 Tornillos Tirafondo 4 Rondanas 4 Taquetes de de 50 mm Plástico de 40 mm PARA COMENZAR NOTA: Una tapa removible cubre el botón de...
  • Page 5: Selección De Una Ubicación

    CONTINUACIÓN DE USO 4. Si el código no funciona, siga de nuevo los pasos REEMPLAZO DE BATERÍAS uno al tres. Si funciona, cierre la caja. NOTA: No combine baterías viejas con nuevas. 5. Cuando abra la caja en el futuro, ingrese el código No combine baterías alcalinas, estándar, de de seguridad y enseguida la tecla y gire la...
  • Page 6 CONTINUACIÓN DE USO 1. Asegure la caja en una pared reforzada y en una repisa permanente o en el piso con los orificios guía en la misma. NOTA: La caja se debe fijar a una pared reforzada en un costado de la caja con los orificios de arriba y abajo en la parte posterior de manera que se asegure a la pared en dos lugares.
  • Page 7: Outils Requis

    H-6731 1-800-295-5510 uline.ca COFFRE-FORT IGNIFUGE STANDARD OUTILS REQUIS Perceuse Tournevis à tête plate Clé de 10 mm Mèche de Mèche de perceuse de perceuse de 3/8 po 3/16 po MATÉRIEL INCLUS Vis tire-fond de Rondelle x 4 Ancrage en plastique...
  • Page 8 UTILISATION SUITE REMPLACER LES PILES 3. Tout en gardant la porte ouverte, composez le code de sécurité, qui peut comporter de trois à huit chiffres, REMARQUE : Ne mélangez pas piles usées et et confirmez le code en appuyant sur la touche piles neuves.
  • Page 9 UTILISATION SUITE Fixez le coffre à un montant de cloison et sur une tablette permanente ou sur le sol à l’aide des avant- trous de montage situés à l’intérieur du coffre. REMARQUE : Le coffre doit être fixé à un montant de cloison sur un des côtés en utilisant les trous inférieur et supérieur situés sur la face arrière du coffre de manière à...

Table of Contents