Table of Contents
Advertisement
Quick Links
Part #
021-4068
021-4069
021-4075
This manual is intended to meet the manufacturer's instructions as required by ANSI Z359
and should be used as part of an employee training program as required by OSHA.
Date of First Use:______________________________
Serial#:____________________________________
Trainer:____________________________________
User:______________________________________
220-00060
Sliding Beam Anchors
Instruction Manual
Reference Image
ANSI Z359.18-2017 Type A, OSHA 1910.140, OSHA 1926.502
User Information
Steel I-Beam
Weight
Width
Min - Max
3.6 lbs.
3-1/2" -14"
(1.6 kg)
5.2 lbs.
12" - 30"
(2.4 kg)
3.6 lbs.
3-1/2" -15"
(1.6 kg)
User Manual
Max Flange
Thickness
1-1/4"
2-5/8"
1-1/4"
Advertisement
Table of Contents
Related Manuals for SafeWaze 021-4068
Summary of Contents for SafeWaze 021-4068
- Page 1 Sliding Beam Anchors Instruction Manual Steel I-Beam Max Flange Part # Reference Image Weight Width Thickness Min - Max 3.6 lbs. 021-4068 3-1/2” -14” 1-1/4” (1.6 kg) 5.2 lbs. 021-4069 12” - 30” 2-5/8” (2.4 kg) 3.6 lbs. 021-4075 3-1/2” -15”...
-
Page 2: Table Of Contents
19.0 MAINTENANCE, CLEANING, AND STORAGE .... 9-10 20.0 INSPECTION ..............10 21.0 WARRANTY ..............10 22.0 UNSAFE OR DEFECTIVE CONDITIONS ....... 10 23.0 PRODUCT LIFE .............. 10 24.0 DISPOSAL ............... 10 25.0 LABELING ............... 10 26.0 INSPECTION FORM ............11 2023 Copyright Safewaze... - Page 3 Swing falls significantly increase the likelihood of serious injury or death in the event of a fall. Contact Safewaze if you have questions regarding compatibility of this equipment that are not covered in this manual. Do not alter or misuse this equipment. Some subsystem components could affect the performance and the operation of this equipment.
- Page 4 (See Figure 14). This information should be recorded in the “Inspection Form” located at the back of this manual (Section 26.0). Questions regarding the use, care, or suitability of this equipment for your application? Contact Safewaze. USER INSPECTION, MAINTENANCE AND STORAGE OF EQUIPMENT Users of personal fall arrest systems shall at a minimum, comply with all manufacturer instructions regarding the inspection, maintenance and storage of the equipment.
-
Page 5: Introduction
1.0 INTRODUCTION Thank you for purchasing a Safewaze Anchorage Connector. This manual must be read and understood in its entirety and used as part of an employee training program as required by OSHA or any applicable state agency. This manual and any other instructional material must be available to the user of the equipment. -
Page 6: Fall Clearance
Weight capacity per OSHA is up to 420 lbs. ***Diagram shown is an example fall clear- ance calculation ONLY. Fall Clearance Diagram Lanyard Length (6’ Total) Required distance from Deceleration Anchorage distance (4’ total) (18’ total) Worker Height (6’ average) Safety factor (2’ total) 2023 Copyright Safewaze... -
Page 7: Limitations And Requirements
All Safewaze full body harnesses must IMMEDIATELY be removed from service if subjected to fall arrest forces. Safewaze full body harnesses shall be inspected by the end user prior to each usage and by a Competent Person other than the user at least annually. These annual inspections shall be documented. -
Page 8: Inspection Frequency
See ANSI Z359.4-2013 for specific rescue information. 11.0 COMPATIBILITY OF COMPONENTS Unless otherwise noted, Safewaze equipment is designed for use with Safewaze approved components and subsystems only. Substitutions or replacements made with non-approved components or subsystems may jeopardize compatibility of equipment and may affect safety and reliability of the complete system. -
Page 9: Making Connections
Do not use equipment that is not compatible. Ensure all connectors are fully closed and locked. Safewaze connectors (snap hooks and carabiners) are designed to be used only as specified in each product’s user instructions. See Figure 4 for examples of inappropriate connections. Do not connect snap hooks and carabiners: •... -
Page 10: Anchor Components
15.0 ANCHOR COMPONENTS FIGURE 5 - ANCHOR COMPONENTS 021-4068 / 021-4069 Anchor Material Components Clamp Assembly Aluminum Alloy Adjustment Levers Aluminum Alloy Fall Protection Plated Steel Attachment Point Support Bar Aluminum Alloy Composite Rollers Nylon Replaceable Jaw Nylon 021-4075 Anchor... - Page 11 Dwg. 3 180° Swivel 1. The 021-4068 and 021-4069 are for use in a horizontal orientation only. They are not designed for use in vertical applications. 2. The work location should be free of debris, and other materials or equipment that could interfere with the proper operation of this equipment.
- Page 12 7. The 021-4075 is designed to slide along the beam in unison with the user’s movement. It can be used in either overhead or foot level tie off applications (See Figure 10 and 11). FIGURE 10 - OVERHEAD USE FIGURE 11 - FOOT LEVEL USE 2023 Copyright Safewaze...
-
Page 13: Jaw Replacement
19.0 MAINTENANCE, CLEANING, & STORAGE 19.1 MAINTENANCE Remove the Safewaze anchor from use if subjected to fall arrest forces or inspection reveals an unsafe or defective condition. If unsafe or defective condition is found, dispose of the anchor as recommended in section 21.0. -
Page 14: Inspection
20.0 INSPECTION • Safewaze Anchors shall be inspected prior to each use by the user, and at least annually by a Competent Person other than the user. Annual inspections shall be documented. Severity of conditions during use may necessitate increased frequency of documented inspections. -
Page 15: Inspection Form
Integrity of Welds / Rivets Labels Paint Contamination Stitching / Wire Condition Heat Corrosion / UV Damage Separation / Bird-Caging NOTES 225 Wilshire Avenue SW, Concord NC 28025 • 800-230-0319 • www.safewaze.com If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE 2023 Copyright Safewaze... - Page 16 Safewaze 225 Wilshire Ave SW Concord, NC 28025 PHONE: 1-800-230-0319 FAX: 1-704-262-9051 WEB: Safewaze.com EMAIL: info@Safewaze.com 2023 Copyright Safewaze...