Page 1
Before this model has being significantly changed to another new version, the parts, appearance and the existing version can be developed and modified that would lead to a slight difference from the original design. DTS reserve ALL the Rights of change of parts and contents WITHOUT...
Foreword Thank you for choosing DTS’s product. For better understanding and usage of DTS550, please read the manual carefully before installation and operation. For your convenience of adjustment, maintenance and other operation, please keep the manual in a proper manner. For further information, please visit Zonda Hobby official website: http://www.zondahobby.com...
5.Do Not re-equip, upgrade or repair your helicopter with the accessories outside the DTS parts catalog in order to ensure the safety of the model structure! 6.Keep people and objects away from the spinning unit and parts in case of damage or injury!
Check of package and accessories Please check the parts and accessories in the package. In the event of defective or missing parts, please contact the retailer for help. 1. Helicopter 2. SD Card 3. Needments Set...
Transmitter Setting Module Before flying, you need to adjust the transmitter data. We use FUTABA T8FG, JR XG8, SPEKTRUM DX8 transmitter as reference for setting parameter. Note that is a setting reference. The actual settings, please adjust according to your helicopter actual situation. FUTABA T8FG LINKAGE MENU MODEL MENU...
Page 7
SPEKTRUM DX8 SETUP LIST Model Select Model Type Swash Type F-Mode Setup Frame Rate Trim Step DTS 550 Helicopter 1 Servo Normal Flight Mode: F Mode 11ms Thr 5 Ele 0 R Trim 0 Type:Common Ail 0 Rud 0 L Trim 0...
MICROBEAST 3 Axis Gyro Parameter Setting SETUP MENU Menu LED solid Status-LED: Purple Red Flashing Red Solid Blue Flashing Blue Solid upright Mounting orientation fl at (horizontal)* (vertical) 50 Hz 120 Hz 200 Hz* Swashplate servo - frequency User defined 65 Hz 165 Hz User defined...
Pre-Flight Controls Test 1.Control Test: Throttle Push the throttle stick upward till the motor start to spin. Ensure the motor spins anti-clockwisely while the main blade spins clockwisely. Throttle Position: Right Throttle Position: Left Please don't push the throttle stick upward over 1/5. The motor will spins at high velocity if the throttle stick is over pushed.
Page 10
3.Control Test: Pitch (only aerobatics use) Swashplate's upward and downward movement Throttle Position: Left Throttle Position: Right Throttle Position: Right Throttle Position: Left Throttle Position: Left Throttle Position: Right 4.Control Test: Aileron Swashplate's Left and Right declining movement (The rudder's control is the same in both left and right-hand throttle transmitter) Rear View Rear View Rear View...
Page 11
5.Control Test: Rudder Tail rotor blades pitch change (The rudder's control is the same in both left and right-hand throttle transmitter) 6. Gyro adjustment Disconnect the connection between ESC and motor, turn on the power of the transmitter and helicopter, move the pushrod to check the sercos direction.
D01 Kit Assemble Procedure Hexagon Socket Head Bolt Insert the damper ring to the rotor M3*8 housing. Make sure the head of spindles are Damper: Ring in the same size and symmetric. 8.0* 14.4*6.5 Spindle Step Spacer 8* 14*1.5 12.8 12.8 Spacer space placed toward outside...
D01 D02 and D06 Kits Assemble Procedure Flange Bearings D01 Kit Assemble Procedure 3* 6*2.5 Make sure the washout control arm Step Spacer set rotate smoothly. 3* 5.5*0.5 Swashplate was installed already. Hexagon Socket Head Bolt M2*5 Flange Bearings 2* 5*2.5 CAUTION Make sure the screw are added with thread-locking fiuld before...
D02 Kit Assemble Procedure D02 Kit Assemble Procedure Same number of screws for the both side main frame. Kimi ScrewX2 M3*12 Remove the ESC mount and bottom frame before install the motor set. Hexagon Socket Head Bolt M3*8 Spacer Hexagon Socket 3* 7*0.8 Head Bolt M3*10...
Page 15
D02 Kit Assemble Procedure Don't lock the M3*18 screws tightly until installing the tail boom completely. Ball Bearing Nylon Lock Nut 12* 18*4 Make sure the gears rotate smoothly. Push till the end for better contact Hexagon Socket Head Bolt M3*18 Ball Bearing 06* 12*4...
D06 D07 Kits Assemble Procedure D06Kit Assemble Procedure D07 Kit Assemble Procedure CAUTION Make sure the screw are added with thread-locking fiuld before Ball Bearing first flight. 8* 14*4 Hexagon Socket Head Screw M3*12 X2 Nylon Lock Nut Approximate Approximate Lock the bearing to the torque tube by applying little amount instant glue.
D04 D05 D07 Kits Assemble Procedure D04 Kits Assemble Procedure Lock the kimi screw to the side of the tail rotor shaft. Make sure all the parts rotate smoothly. Flange Bearings 2* 5*2.5 Lock the kimi screw to the side Hexagon Socket Head Bolt of the tail rotor M2*5...
D04 D05 D07 D08 Kits Assemble Procedure D04 D05 D07 Kits Assemble Procedure Install the torque tube to the torque tube rear drive gear. Tail boom aligns to the tail boom Lock the screws tightly after mount. installing the tail boom completely. Scews pass through the vertical fin mount cap, tail case and the tail boom hole.
Main Blade and Electronic Parts Assemble Procedure Hexagon Socket Head Bolt M4*30 X2 Nylon Lock Nut Don't tie the velcro to the gyro too tightly. Microbeast 3-Axis Gyro Double-sided Stickers Hexagon Socket Head Screw M3*6 X4 Hexagon Socket Head Bolt M3*8 X4 Spacer 3* 7*0.8...
Page 23
22.2V 5000mAh 30C Li-Po Battery (not included) Velcro BEC 15A Double-sided Stickers Microbeast 3-Axis Gyro Tie the ESC: BEC tightly. Hook And Loop Strap 22.2V 5000mAh 30C Li-Po Battery (not included) Hook And Loop Strap BEC 15A Hook And Loop Strap 6S 130A ESC...
Page 26
Parts List Description Specification Description Specification need need Fun Key Main Blade Canopy Canopy+ Mount Grommet 560mm, Hexagon Socket Head Bolt Ball Link M4*12 S 4.75*L20 Spacer Pushrod 4* 12*1.0 M2.3*L36 Ball Bearing 8* 16*5 Blade Holder Thrust Bearing F8*16M Microbeast 3-Axis Gyro Main Rotor Blade Grip Nylon Lock Nut...
发射机设置 直升机飞行前必须先设置发射器的相关参数。为了您能更快的享受飞行,我们特选择了FUTABA T8FG、 JR XG8、SPEKTRUM DX8的发射器为例子来设置相关参数,请注意这只是一个举例说明,实际设置请根据 自身的实际情况而定。 FUTABA T8FG LINKAGE MENU MODEL MENU REVERSE Model Type PIT CURVE TYPE HELICOPTER 1AIL 6PIT NORM NORMAL +100 2ELE 7GOV NORM SWASH IDLEUP1 +100 -100 3THR 8NDL NORM RESET IDLEUP2 +100 -100 4RID NORM NORM IDLEUP3...
Page 35
SPEKTRUM DX8 SETUP LIST Model Select Model Type Swash Type F-Mode Setup Frame Rate Trim Step DTS 550 Helicopter 1 Servo Normal Flight Mode: F Mode 11ms Thr 5 Ele 0 R Trim 0 Type:Common Ail 0 Rud 0 L Trim 0...
Page 58
Global Distribution Office Zonda Hobby Technologies Electronic Ltd Workshop No.1, 1st Floor, Kam Hon Industrial Building, No.8 Wang Kwun Road, Kowloon Bay, Kowloon, Hong Kong Tel : 852-3160 8886 Fax : 852-3160 8884 Email: Michael@zondahobby.com, Jason@zondahobby.com Official Website: www.zondahobby.com...
Need help?
Do you have a question about the 550 and is the answer not in the manual?
Questions and answers