Specification - HOGERT HT4R630 User Manual

EN
USER'S MANUAL
AIR RATCHET WRENCH HT4R630
Thank you for purchasing our product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE
OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE
FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DA-
MAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE
WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
WARNING! Ensure that Health & Safety, local authority and general
workshop practice regulations are adhered to when using this
equipment.
WARNING! Disconnect from the air supply before changing accesso-
ries, servicing or performing any maintenance.
- Maintain the tool in good condition (use an authorised service agent).
- R eplace or repair damaged parts. Use genuine parts only. Unautho-
rised parts may be dangerous and will invalidate the warranty.
- Use in a suitable work area. Keep area free from unrelated mate-
rials and ensure that there is adequate lighting.
- M aintain correct balance and footing. DO NOT over reach, ensure
the floor is not slippery and wear non-slip shoes.
WARNING! Always wear approved eye and hand protection when
operating these tools.
- U se face, dust, or respiratory protection in accordance with COSHH
regulations.
WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we re-
commend
that suitable respiratory protection is worn.
- D epending on the task, the tool noise level may exceed 84dB in which case wear safety ear defenders.
- R emove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain and/or tie back long hair.
- Wear appropriate protective clothing and keep hands and body clear of working parts.
- Keep children and unauthorised persons away from the work area.
- E nsure that the workpiece is secure before operating the tool. Never hold a workpiece by hand.
- DO NOT operate tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure 90PSI.
- Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
- When not in use disconnect from air supply and store in a safe, dry, childproof location.
- DO NOT use the tool for tasks that it is not designed to perform.
- DO NOT operate tool if any parts are damaged or missing as this may cause failure and/or personal injury.
- DO NOT carry the tool by the hose, or yank the hose from the air supply.
- DO NOT place air line attachments close to your face and do not point at other people or animals.
- DO NOT direct air from the air line at yourself or others.
- DO NOT operate tool unless you have been instructed in use by a qualified person.
- DO NOT carry tool with your finger on the trigger and avoid unintentional starting.
- DO NOT drop, throw or abuse the tools as they are precision instruments.
- DO NOT leave the tool operating unattended.
- DO NOT get the tool wet or operate in damp or wet locations.
- DO NOT allow tool to free run for an extended period of time as this will shorten its life.
INTRODUCTION
Air powered ratchet with hardened steel anvil and twist reverse mechanism. Trigger operated power control. Suitable for use in the
engine bay where there is limited space for hand operated ratchets.

SPECIFICATION

model no HT4R630
Drive 1/2"Sq
Max. Torque 45 lb.ft(61Nm)
Free Speed 150 rpm
Air Consumption 141,5 l/min
Operating Pressure 90 PSI
Air Inlet size 1/4" BSP
Length 265 mm
Adres producenta/ Adresse des Herstellers/ Manufacturer's Address/ Адрес производителя
GTV Poland Sp. z o.o. Sp. k., ul. Przejazdowa 21, 05-800 Pruszków
7