Larson Electronics WAL-M-3X48LED-120 Installation Manual

Larson Electronics WAL-M-3X48LED-120 Installation Manual

144 watt led flood light - 3x 200lb. magnets on aluminum base ip67 - 120-277vac

Advertisement

144 Watt LED Flood Light - 3x 200lb. Magnets on Aluminum Base
Thank you for your purchase of the Larson Electronics WAL-M-3X48LED-120 aluminum flood light fixture.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE WAL-M-3X48LED-120
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –
RISK OF PERSONAL INJURY –
RISK OF BURN –
ALLOW FIXTURE TO COOL BEFORE SERVICING.
PEOPLE
WITH
ELECTROMAGNETIC FIELDS IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE
PACEMAKER INTERFERENCE OR PACEMAKER FAILURE.
KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR.
The WAL-M-3X48LED-120 LED work light from Larson Electronics is capable of illuminating an area 675 feet in length by
450 feet in width with 8,640 lumens of brilliant illumination. This compact 120 volt work light comes attached to an
aluminum bracket equipped with three 200 lbs. grip magnetic feet that allows operators to easily mount this unit to any
ferrous metallic surface. This light can be mounted overhead, on tank walls etc. and will stay firmly in place. This unit
includes a waterproof step down transformer to operate the low voltage LED light emitters off standard 120V current.

Mounting

Mounting of this fixture is achieved using the three 200lb
grip magnets at the back of the fixture. Simply stick the
fixture in the desired position to any magnetic metallic
surface capable of supporting the load of the fixture.
Clean the surface before mounting, and be sure to keep
fingers clear of the magnets as they could cause injury.
Take care when removing to not slide the fixture,
especially on painted surfaces, as this could cause
scratches or damage.

Power

WARNING: Check product label for correct voltage!
The light emitters are "instant on" and will power on as
soon as they are supplied with proper voltage. Simply
mate the power cord with the built in transformer via the
quick disconnect Deutsch connector, then plug the power
cord into a compatible receptacle outputting the correct
voltage. The 48 Watt LED light emitters produce 8,640
lumens combined and will illuminate a workspace 675` L
X 450` W in size. This versatile work light can be used as
an overhead light, pedestal light, and just about
anywhere a portable and economical, yet powerful
illumination is needed, and a surface for mounting exists.
Larson Electronics, LLC
IP67 - 120-277VAC
Instruction Manual
MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
PACEMAKERS
SHOULD
Phone: (877) 348-9680
CONSULT
THEIR
PHYSICIAN(S)
Deutsch
Connector
Magnetic Mounts
Fax: (903) 498-3364
WAL-M-3X48LED-120
BEFORE
QUICK DISCONNECT
DEUTSCH CONNECTOR
www.larsonelectronics.com
USE.
1 of 2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WAL-M-3X48LED-120 and is the answer not in the manual?

Questions and answers

Summary of Contents for Larson Electronics WAL-M-3X48LED-120

  • Page 1 KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR. The WAL-M-3X48LED-120 LED work light from Larson Electronics is capable of illuminating an area 675 feet in length by 450 feet in width with 8,640 lumens of brilliant illumination. This compact 120 volt work light comes attached to an aluminum bracket equipped with three 200 lbs.
  • Page 2 Inspect for good working condition prior to storage and before re-use. REPLACEMENT PARTS The WAL-M-3X48LED-120 is designed to provide years of reliable performance. Should the need for replacement parts arise, please contact Larson Electronics. THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

Table of Contents