Page 1
INSTALLATION MANUAL MODELS: JS-1500R SWINGER LIFT 17611 East St, North Fort Myers, FL 33917 (239) 337-4141 REVISION A GoldenMarineSystems.com GoldenBoatLifts.com PUBLISHED 10/18/2020...
Page 2
MOUNT SEADRIVE………………………………………………………………………………….14 MOUNT MOTOR……………………………………………………………………………………….15 REFERENCE NOTES ................16 INTRODUCTION We at Golden are proud to introduce the Swinger Lift to our line of lifts. SWINGER LIFT (Pile Mount) The Swinger Lift is designed to easily lower small vessels into the water directly off a seawall or dock.
Page 3
SAFETY INFORMATION (READ THOROUGHLY) follow these instructions before attempting to operate the The JS-1500R PWC (Personal Water Craft) Swinger Lift was Swinger Lift may cause damage to the lift and/or personal designed, tested and certified to be installed in the injury/death.
Page 4
JS-1500R MAST MOUNTING PILING SEAWALL BUNK CRADLE CRADLE CAPACITY MAST HOUSING CABLE GUIDEPOST(S) BUNK(S) BRACKET(S) MOUNT MOUNT BRACKET BEAM(S) ARM(S) ASSEMBLY STANDARD 1.72 X 4” 1/4" DIA. 4.03 X 4 X 1/4 X 5 X 10” 2 X 2 X .25”...
REQUIRED TOOLS HARDWARE (cont.) Hex Bolt QTY: 9/16” Open End Wrench 3/4” Open End Wrench 3/8” X 1” 15/16” Open End Wrench 1/2” X 1-1/2” 1/2” X 2-1/2” 1/2” X 4-1/2” 1/2” X 5” 5/8” X 4-1/2” 3/4” X 5” 5/8”...
Page 7
REQUIRED PARTS (Piling) GENERAL ASSEMBLY INSTRUCTIONS Please read all instruction provided before starting the installation of the JS-1500R Swinger Lift. It is recommended that the Swinger Lift is installed by trained professionals only. Please ensure that there is an appropriate area...
Page 8
REQUIRED PARTS (Piling) ATTACH MOUNT (Piling) Using three (3) 5/8” Bolts (not included), secure the HARDWARE QTY: mount to the piling by inserting an appropriate bolt Pile Mount through each of the three (3) holes in the piling Hardware mount, and completely through the piling, as shown (not included) in figure 1.
Page 9
REQUIRED PARTS (Seawall) ATTACH MOUNT (Seawall) HARDWARE QTY: NOTE: It is recommended to use more than one person for this step to ensure the lift stays upright at all times. 3/4" Seawall Mount Hardware NOTE: it is recommended to have a trained professional (not included) pre-drill the SEAWALL MOUNT holes into the seawall to 1/2"...
MOUNT MAST & MAST HOUSING REQUIRED PARTS NOTE: From remaining steps, PILING HARDWARE QTY: MOUNT/SEAWALL MOUNT will be referred to as “MOUNT” 5/8” x 4-1/2" Hex Insert the MAST into the MAST HOUSING with the Bolt four holes in the MAST oriented toward the bottom. 5/8"...
Page 11
ATTACH CRADLE ARMS & REQUIRED PARTS CABLE HARDWARE QTY: Align the four (4) holes in both CRADLE mounting 1/2” x 5" Hex Bolt plates with the four (4) holes on each side of the 3/4" x 5" Hex Bolt lower MAST . Slip one (1) 1/2"...
Page 12
REQUIRED PARTS MOUNTING BUNK BRACKETS HARDWARE QTY: Position the brackets so that the side with the single hole is oriented upwards. Align the brackets so that 3/8” X 5-1/2” Hex Bolt all the holes align with the holes on the other 3/8”...
Page 13
MOUNTING BUNKS REQUIRED PARTS Sliding the connected brackets away from each HARDWARE QTY: other, position the BUNK between two (2) sets of 3/8” X 4” Hex Bolt brackets so that the single hole in the brackets are 3/8” Hex Nut aligned with the single hole on the bunk for each set as shown in figure 11.
Page 14
SEA-DRIVE INSTALLATION REQUIRED PARTS Insert the drive shaft into the cable spool shaft, HARDWARE QTY: making sure the holes in both shafts are aligned 1/2" X 2-1/2” Bolt properly to allow for hardware. Rotate the SEA DRIVE so the motor mounting flange 1/2"...
Hex Bolt and insert it through the hole in the motor mount and into the threaded hole in the flange and securely fasten. NOTE: Golden Boat Lifts recommends that a licensed electrician wire and install the electrical components on the Swinger Lift. Failure to follow this recommendation may lead to injury, death, or damage to the lift.