Using The Scrub Blast Accessory; Using The Ez Reach Bending Duster Accessory; Using The Flat Scrubber Accessory; Using The Steam Duster Accessory - Shark S4701D Owner's Manual

Using Your Handheld Steamer - continued

USING THE SCRUB BLAST ACCESSORY

Cleaning Tip: The Scrub Blast Accessory is ideal for
large, flat surfaces. Its design allows you to apply more
force when scrubbing, which redistributes the steam
toward the Cleaning Pad when pressed against a surface.
CAUTION: Make sure the Steam Mop is unplugged
or in Standby Mode while attaching or removing
the Scrub Blast Accessory. Avoid touching the
Accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
CAUTION: This is not an iron. Do not use on
garments or soft surfaces. It may result in damage.
1
To attach the Scrub Blast Pad, place it exterior side
down on a flat surface, then set the Scrub Blast
Accessory into the inside of it. Pull the Pad over the
edges of Accessory until it fits snuggly.
2
Attach the Scrub Blast Accessory by connecting it to
the Direct Steam Nozzle until it clicks into place.
3
When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning). Steam will
blast from the front tip of the Accessory —press the
Accessory against the surface you wish to clean,
and the steam will redirect into the Pad. Continue to
press the Accessory down as you clean.
4
To remove the Scrub Blast Accessory, squeeze the
Accessory Release Buttons, then slide out the
Accessory.
17 1-800-798-7398
USING THE EZ REACH BENDING DUSTER
ACCESSORY
Cleaning Tip: The EZ Reach Bending Duster Accessory is
ideal for dusting a variety of surfaces, especially hard-to-
reach ones.
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the EZ Reach Bending Duster
Accessory. Avoid touching the Accessory, as it
will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Make sure ceiling fans are off before
cleaning/dusting them.
1
Slide the EZ Reach Bending Duster Pad all the way up the
EZ Reach Bending Duster Accessory so it fits snuggly.
2 Cinch the elastic band and slide the locking toggle
to tighten.
3
Attach the EZ Reach Bending Duster Accessory
by connecting it to the Direct Steam Nozzle until it
clicks into place.
4
When you press the Steam Control Button Accessory
Mode (ACC) will automatically be selected and you
can begin cleaning (LO and HI Settings are not
available for above-floor cleaning).
5
To bend the accessory into the desired position, pull
back on the buttons on the sides of the EZ Reach
Bending Duster Accessory.
6 To remove the EZ Reach Bending Duster Accessory,
squeeze the Accessory Release Buttons, then slide
out the Accessory.

USING THE FLAT SCRUBBER ACCESSORY

Cleaning Tip: The Flat Scrubber Accessory is ideal for
a variety of surfaces. Its design allows you to apply more
force when scrubbing.
CAUTION: Make sure the Steam Mop is
unplugged or in Standby Mode while attaching
or removing the Flat Scrubber Accessory.
Avoid touching the Accessory, as it will be
very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
CAUTION: Do not use on wallpaper.
1
To attach the Flat Scrubber Pad, place it exterior side
down on a flat surface, then set the Flat Scrubber
Accessory into the inside of it. Pull the Pad over the
edges of Accessory until it fits snuggly.
2
Attach the Flat Scrubber Accessory by connecting it
to the Direct Steam Nozzle until it clicks into place.
3
When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
4 To remove the Flat Scrubber Accessory, squeeze
the Accessory Release Buttons, then slide out the
Accessory.

USING THE STEAM DUSTER ACCESSORY

Cleaning Tip: The Steam Duster Accessory is ideal for
cleaning and dusting a variety of surfaces, like large areas,
hard-to-reach places, and crevices.
CAUTION: Make sure the Steam Mop is unplugged
or in Standby Mode while attaching or removing
the Steam Duster Accessory. Avoid touching the
Accessory, as it will be very hot after steaming.
CAUTION: To avoid scalding injuries, always unplug
and allow the Steam Mop to cool before removing
or changing Accessories or Cleaning Pads.
1 Slide the Steam Duster Pad all the way up the Steam
Duster Accessory so it fits snuggly.
2
Cinch the elastic band and slide the locking toggle to
tighten.
3
Attach the Steam Duster Accessory by connecting it
to the Direct Steam Nozzle until it clicks into place.
4 When you press the Steam Control Button Accessory
Mode (ACCESSORY) will automatically be selected
and you can begin cleaning (LO and HI Settings are
not available for above-floor cleaning).
5
To remove the Steam Duster Accessory, squeeze
the Accessory Release Buttons, then slide out the
Accessory.
www.sharkclean.com
EN
18