Lincoln Electric OPTIMARC CV355P Operator's Manual
  1. Manuals
  2. Brands
  3. Lincoln Electric Manuals
  4. Welding System
  5. OPTIMARC CV355P
  6. Operator's manual

Lincoln Electric OPTIMARC CV355P Operator's Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
OPTIMARC
Safety Depends on You
Lincoln arc welding and cutting
equipment is designed and built
with safety in mind. However, your
overall safety can be increased by
proper installation and thoughtful
operation on you part. DO NOT
INSTALL, OPERATE OR REPAIR
THIS EQUIPMENT WITHOUT
READING THIS MANUAL AND
THE SAFETY PRECAUTIONS
CONTAINED THROUGHOUT.
And, most importantly, think before
you act and be careful.
For use with machine Part Number K60171-1, Code 76457
• World's Leader in Welding and Cutting•
THE SHANGHAI LINCOLN ELECTRIC COMPANY
No. 195, Lane 5008, Hu Tai Rd. Baoshan, Shanghai, PRC 201907
www.lincolnelectric.com.cn
CV355P
®
Copyright © 2020 The Shanghai Lincoln Electric Company
IM7032-1
Feb., 2020
Rev. 01
Rev. 01

Advertisement

Table of Contents
loading

Related Manuals for Lincoln Electric OPTIMARC CV355P

Summary of Contents for Lincoln Electric OPTIMARC CV355P

  • Page 1 CONTAINED THROUGHOUT. And, most importantly, think before you act and be careful. Copyright © 2020 The Shanghai Lincoln Electric Company • World’s Leader in Welding and Cutting• THE SHANGHAI LINCOLN ELECTRIC COMPANY No. 195, Lane 5008, Hu Tai Rd. Baoshan, Shanghai, PRC 201907 www.lincolnelectric.com.cn...
  • Page 2 Thank you for selecting QUALITY Lincoln Electric products. Please examine the packaging and equipment for damage. Claims for material damaged in shipment must be notified immediately to the authorized dealer from whom you purchased the machine. For future reference, please record your equipment identification information in the table below. Model Name, Code &...
  • Page 3 SAFETY OPTIMARC ® CV355P Rev.01...
  • Page 4 SAFETY OPTIMARC ® CV355P Rev.01...
  • Page 5 SAFETY OPTIMARC ® CV355P Rev.01...

  • Page 6: Installation

    For any maintenance or repair operation it is recommended to contact the nearest technical service center or directly consult machine division of the Shanghai Lincoln Electric. Maintenance or repairs performed by unauthorized service center or personnel will void the manufacturer’s warranty.

  • Page 7: Safety Precautions

    INSTALLATION SAFETY PRECAUTIONS Read the entire installation section before starting installation. INPUT POWER AND GROUNDING WARNING CONNECTION WARNING ELECTRIC SHOCK can kill. Only qualified personnel should perform this Only a qualified electrician should connect the installation. input leads to the OPTIMARC®. Connections Turn the input power OFF at should be made in accordance with the connection the main switch or fuse box...
  • Page 8 INSTALLATION PROCESS SELECTIONS AND metal electrical contact. Poor work lead connections can result in poor welding performance. CONNECTIONS WARNING To avoid interference problems with other equipment and to achieve the best possible operation, route all cables directly to the work and wire feeder. Avoid excessive lengths and do not coil excess cable.

  • Page 9: Operation

    OPERATION Turn the OPTIMARC® CV machine’s power switch CAUTION “OFF”. Connect the control cable from the PWF wire feeder For secure electrical connection, the screws connecting the output terminals and cables must to the 6-pin connector. be tightened. Damage may occur to the output stud or welding performance maybe compromised.
  • Page 10 INSTALLATION protection device. When the machine has gone into thermal overload, the output will be turned off and the SAFETY PRECAUTIONS thermal indicator light will be turned “ON“. When the machine has cooled to a safe temperature, the Thermal Read this entire section of operating Indicator Light will go out and the machine may resume instructions before operating the machine.

  • Page 11: Operational Features And Controls

    OPERATION OPERATIONAL FEATURES AND release the trigger. 4-STEP mode – crater function initiates when uses “Clicks” trigger again after CONTROLS releasing it. Please see FIGURE B.3 and B.4 to know ® the more details of time sequence of OPTIMARC FRONT PANEL (SEE FIGURE B.1) CV355P.
  • Page 12 OPERATION REAR PANEL (PLEASE SEE FIGURE B.2). 22. FUSE AND FUSE HOLDER 250V 8A fuse is used to protect the auxiliary power for the wire feeder. 17. INPUT CABLE HOLDING BRACKET This bracket securely holds the three phase power cables in place.
  • Page 13 OPERATION FIGURE B.3 FIGURE B.4 FIGURE B.5 OPTIMARC ® CV355P Rev.01...

  • Page 14: Dip Switch Descriptions

    OPERATION DIP SWITCH DESCRIPTIONS crater. For more details, please see FIGURE B.5. ® OPTIMARC machine offers a DIP switch on the 4. SPECIAL FUNCTION TEST It enables a test procedure to test the control knobs control board, which allows user to have additional and the toggle switches, when the DIP switch 4 is ON features.

  • Page 15: Troubleshooting

    TROUBLESHOOTING If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your local authorized Lincoln Electric CAUTION Field Service Facility for technical assistance. Observe all Safety Guidelines detailed in the beginning and throughout this manual.
  • Page 16 TROUBLESHOOTING If for any reason you do not understand the test procedures or are unable to perform the tests/repairs safely, contact your local authorized Lincoln Electric CAUTION Field Service Facility for technical assistance. Observe all Safety Guidelines detailed in the beginning and throughout this manual.
  • Page 17 Except for special instructions, experiments on welding machines are conducted in accordance with the general standard of IEC60974-1; experiments on welding consumables are conducted in accordance with the general standard of AWS; for speci c applicable standards on welding consumables please refer to the product page. The product performance data of this website and related attachments are from LINCOLN ELECTRIC American application engineering laboratory.

Table of Contents