Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Culina ICONCG60RF
Summary of Contents for Culina ICONCG60RF
- Page 1 Instruction Manual Cooker Hood MODEL:ICONCG60RF...
- Page 2 [01] x1 [02] x1 [03] x1 [04] x1 [05] x1 [06] x1 [07] x6 [08] x6 [09] x4 (4 x 32mm) (3.5 x 10mm) [10] x4 [11] x4 [12] x4 [13] x1 CARBFILT4 Not included VENT PACK (Ø 150mm This appliance includes a universal motor body. Replacement glass panels are available. Please contact the customer service helpline for advice at the end of the Care &...
- Page 3 Cooker Hood ICONCG60RF...
-
Page 4: Table Of Contents
Let's get started Getting stared safety Specifications Installation care and maintenance... -
Page 5: Getting Stared
Getting Started... -
Page 6: Safety
safety safety instruction There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels; There is a fire risk if cleaning is not carried out in accordance with the instructions; Do not flambe under the range hood;... -
Page 7: Specifications
Specifications Specifications Voltage : 220-240V ~50Hz Motor power : 90W Lamp power : 1*3W No cap 385mmx10mm... -
Page 8: Installation
Installation VENT PACK CARBFILT4 (Ø150mm) CARBFILT4 VENT PACK (Ø150mm) Choose a type of installation: Ducted option A (extraction to the outside) or Recirculation option B (no extraction to the outside). This appliance is for installation on a wall only. - Page 9 Installation 120mm 188mm 631-906mm 180mm ≥ 760mm Mark the wall with the hole positions as shown in the diagram. The fixing supplied are suitable for solid walls only. When fixing to any other type of wall use suitable alternative fixings Warning: Caution! Before drilling it is extremely important to check the wall for hidden pipes, electrical cables etc using an appropriate detection device.
- Page 10 Installation [07] [08] [07] x6 [08] [08] x2 (4 x 32mm)
- Page 11 Installation [04] [04] x1 [08] x2 425 - 700mm (4 x 32mm) [08] WARNING: Use only the same size of fittings and mounting screws a recommended in this instruction manual. Failure to follow these instructions may result in electrical hazards.
- Page 12 Installation [08] x2 (4 x 32mm) [08] [02] [11] x4 [13] [10] [12] x4 [13] x1 Tighten all screws (do not overtighten). [10] x4 [11] [12] [02] x1...
- Page 13 Installation [09] [06] [06] x1 [09] x2 (3.5 x 10mm) VENT PACK (150mm)
- Page 14 Installation [03] [03] x1 Only for recirculation option. CARBFILT4 CARBFILT4...
- Page 15 Installation [03] [03] x1 [09] x2 (?.5 x 10mm) [09]...
- Page 16 Installation Stainless steel only. [05] x1 [05]...
- Page 17 Installation All installation must be carried out by a competent person or qualified electrician Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. Direct Connection The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts.
-
Page 18: Use
Before you start WARNING: Read the instructions before using the appliance. Switch on the appliance at the switched fused connection unit. The appliance is ready for use. Function & Settings Four-button panel To obtain the best results from your cooker hood it is recommended that you leave it switched on for up to 15 minutes after you have finished cooking Light On/Off Fan On/Off and Speed Reduction... - Page 19 NOTE: This operation must be undertaken within two minutes of switching the power on at the mains outlet. To change this setting at a later time, switch off the power at the mains outlet, wait a few seconds, turn on the power and repeat the above.
- Page 20 IMPORTANT: This section is only applicable if you have purchased the optional.Cooker Hood Model:ICONCG60RF Before First Use This cooker hood model ICONCG60RF and the ceramic hob model ICONCER60RF must be paired by radio frequency before remote control can occur. This only needs to be done once.
- Page 21 Using the connectivity function 1.Ensure the connectivity indicator is lit on the hob control panel. 2.The extraction rate of the hood will vary based upon the total power output selected on the hob,as shown in the table. Each hob cooking zone has a maximum rated output of 10 comprising 1-9.
-
Page 22: Care And Maintenance
Care&Maintenance Carbon filter replacement Replace carbon filters every three month MONTHS CARBFILT4 2x Carbon filter, model number CARBFILT4, available via the customer helpline - see end of Care & maintenance section for details. If the motor is off, and after the fan has been in operation for approximately 150 hours, the display will show and the Timer will flash red to advise you to replace the carbon filters After replacing the filters, reset the alert by pressing... - Page 23 Care&Maintenance 1 MONTH 65 C º ≤ If the motor is off, and after the fan has been in operation for approximately 50 hours, the display will show and the Timer will flash red to advise you to clean the aluminium grease filters After cleaning the filters, reset the alert by pressing the Timer icon WARNING: Increase the filter cleaning/replacement frequency if the hood is used for more than 2 hours a day.
- Page 24 Care&Maintenance The specifications plate is available on this appliance. This plate displays all the necessary identification information for ordering replacement parts. If you sell the appliance, give it away, or leave it behind when you move house, make sure you also pass on this manual so that the new owner can become familiar with the appliance and its safety warnings.
Need help?
Do you have a question about the ICONCG60RF and is the answer not in the manual?
Questions and answers