Table of Contents
Advertisement
Connections
• "LPA" appears for "From Main" when "Long Pre-Alarm
Area" (System Menu Memory Data Management
Setting for Main Memory Change Partition Setting)
is set to other than "0 %" in the recorder.
3. Set the start time of copy.
step
Start: Sets the start point of copy.
Continue: Starts copying from the end point of the
previous copy.
• To set the start point using the book mark, select
"Bookmark" and then select the desired book
mark number.
• To copy from the oldest recording time, select
"Copy Start Time."
4. Select "Execute."
step
• The copy starts.
• To stop the copy manually, select "Cancel" in the
screen of <Copy Data to Copy 2 Drive>. The data
which has been copied before cancelling is
copied.
• The warning is displayed when the copied range
exceeds the available capacity of the device to be
copied when "FIFO Overwrite" is set to "Off" and copy
destination is HDD. In this case, set the copy setting
again with narrower copy range or use a copy device
with larger capacity.
• When the copy is performed during recording, the
picture of the recording start and end points may not
be recorded.
• The progress bar of copy is not displayed for copy 2.
• The picture data is processed in 2 MB unit. Therefore
the data is copied in 2 MB unit from the start point of
the designated range when copying.
5. Attaching and removing the HDD
Up to 2 HDDs can be mounted on this unit. The attaching,
removing and replacing method of the HDDs are as fol-
lows.
• Disconnect the power supply from the Mains before
installing or removing the HDD.
• When attaching the HDDs, attach in the order of HDD
1, and 2.
Precautions for installation
Precautions for attaching or removing the HDD
• Do not attach or remove the HDD unnecessarily.
Attaching or removing the HDD of DX-ZD5UE(Z) is
intended to replace the faulty HDD or add the HDD
when starting operation for the first time because of
the structure of the connectors. It is not presumed to
be used as a removable HDD.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
10
• Make sure that the MAIN switch on the rear panel is
turned OFF when attaching or removing the HDD.
Wait at least 1 minute after turning off the power. When
a recorder is connected, turn off the recorder, too.
• Do not remove the top cover of the unit.
• When a power failure occurs during recording, avoid
adding, replacing or transporting the HDD. In this
case, as the recorded data may be erased, turn the
power back on to boot up the unit normally with the
HDD that was being used at the time of the power
failure attached. Then add, replace, or transport the
HDD.
• HDD is very delicate. Handle the HDD with care and
follow the precautions below because even a small
shock may damage the internal components of the
HDD.
• Do not drop the HDD. Also do not put the metallic
object such as a coin or a screw driver into the HDD
tray.
• Do not place the HDD on a desk or a table directly.
Put a thick cushion under the HDD because even a
small shock may damage the internal components
of the HDD.
• Do not use an electric screwdriver. Vibrations and
shocks caused by an electric screwdriver may
damage the internal components of the HDD.
• When replacing the HDD, do not knock the HDD
with other components such as the another HDD
and the HDD tray.
• Do not knock the HDD with tools such as a driver
when replacing the HDD.
• The following HDD has been tested and compatibility
is ensured. This information is as of December 2004.
Supply of this HDD may be stopped or it may be
changed without notice by its manufacturer. Consult
your dealer for the latest information or use of other
HDDs. When you attach multiple HDDs, normally use
the HDDs of the same capacity and the same model
name.
<Hitachi Global Storage Technologies>
HDS724040KLSA80 (400 GB, S-ATA)
When attaching a HDD
1. Push the left end of each screw covers on both sides
step
of the cover to open.
• Do not leave the screw cover open for general use.
Advertisement
Table of Contents
