Mitsubishi Electric XD460U Control Manual page 3

6) Keystone commands
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
KEYSTONE(vertical)
KEYSTONE(horizontal)
How to set the grade
Use the ASCII codes to set the grade for setting data. Please refer to the table below for the HEX code.
ASCII '+' '–'
HEX 2Bh 2Dh
7) Mute commands
screen is being displayed, the splash screen is not muted but only canceled.)
The mute commands are used for the mute setting of this projector with the 0(30h) and 1(31h).
ITEM
MUTE
8) Remote commands
screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
Button's name on remote
+ VOLUME
– VOLUME
KEYSTONE
EXPAND
PinP
MUTE
{
}
$
%
MENU
ENTER
AUTO POSITION
STILL
ASPECT
WALL SCREEN
CE
[Example] When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII
codes.):
Sending commands
from the PC, etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' ' '
9) Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is
sent with a 4-digit figure (password) added to the end of the data code. When the password lock is enabled or
disabled successfully, the projector sends a return command comprising the data code, password, and "1" at the
end. When enabling or disabling the password lock fails, it sends a return command with "0" at the end. There is
no reconfirmation of the password. The password input command is for enabling projection of image when
password lock has been set to DISPLAY INPUT. The password input command is sent with a 4-digit figure
(password) at the end.
ITEM ASCII
Password lock PSLOCK
enabling/ disabling
Password input PASS
is a 4-digit figure (password).
****
(Not executable in stand-by mode. Possible only to read during muting.)
ASCII HEX
KS 4Bh 53h
KSH 4Bh 53h
'0' '1' '2' '3'
30h 31h 32h 33h
(Not executable in stand-by mode. When the mute commands are sent while the splash
ASCII HEX
MUTE 4Dh 55h
(Not executable in stand-by mode. When the remote commands are sent while the splash
ASCII HEX
r06 72h
r07 72h
r43 72h
r02 72h
r04 72h
ra6 72h
r53 72h
r2b 72h
r4f 72h
r59 72h
r54 72h
r10 72h
r09 72h
ra4 72h
re2 72h
rd7 72h
re7 72h
Status code from
the projector
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
HEX
50h 53h
50h 41h
VALUE
±35
48h ±25
'4' '5' '6'
34h 35h 36h
VALUE
0 (OFF), 1 (ON)
54h 45h
30h 36h
30h 37h
34h 33h
30h 32h
30h 34h
61h 36h
35h 33h
32h 62h
34h 66h
35h 39h
35h 34h
31h 30h
30h 39h
61h 34h
65h 32h
64h 37h
65h 37h
'
4Ch 4Fh 43h 4Bh
53h 53h
3
'7' '8' '9'
37h 38h 39h
Description
Command operating the same
as the MENU button
Command receipt confirmation
(Command echo back)
VALUE
0****(Disabling), 1****(DISPLAY INPUT)
2****(MENU ACCESS)
****