Page 1 55” LCD TV chassis PL15.16 Service Manual Contents TYPE A TYPE D 55PFL6900/F7 PHILIPS (Serial No.: DS1) 55PFL6900/F7 A PHILIPS (Serial No.: DS2) 55PFL6900/F8 PHILIPS (Serial No.: XA1, TC1) 55PFL6900/F8 A PHILIPS (Serial No.: DS1, TC1) TYPE E TYPE B...
Page 2 IMPORTANT SAFETY NOTICE Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
Page 3: Table Of Contents
TABLE OF CONTENTS Specifications [TYPE A, B] ..............1-1 [TYPE C, E].
Page 4: Specifications [Type A, B]
SPECIFICATIONS [TYPE A, B] < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBV 2. Synchronizing Sens. CA.ch.31 dBV CA.ch.87 dBV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...
Page 5: [Type C, E]
[TYPE C, E] < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBV 2. Synchronizing Sens. CA.ch.31 dBV CA.ch.87 dBV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...
Page 6: [Type D]
-89 to 89 3. Viewing Angle Vertical ° -88 to 88 Vertical ° -89 to 89 *1 : 55PFL6900/F7 A, 55PFL6900/F8 A (Serial No.: DS1) *2 : 55PFL6900/F8 A (Serial No.: TC1) < VIDEO > Description Condition Unit Nominal Limit Horizontal 5±5...
Page 7 < AUDIO > All items are measured across 8  load at speaker output terminal with L.P.F. Description Condition Unit Nominal Limit 1. Audio MAX Output (ATSC 0dBfs) Lch/Rch 10.0/10.0 9.0/9.0 2. Audio Distortion (NTSC) 500mW: Lch/Rch 0.5/0.5 2.0/2.0 PL15.16SP...
Page 8: [Type F]
[TYPE F] < TUNER / NTSC > Description Condition Unit Nominal Limit 1. AFT Pull-In Range ±2.3 ±2.1 TV.ch.4 dBV 2. Synchronizing Sens. CA.ch.31 dBV CA.ch.87 dBV < TUNER / ATSC > Description Condition Unit Nominal Limit 1. Received Freq. Range (-28dBm) ±100 ch.4 -76/0...
Page 9 < AUDIO > All items are measured across 8  load at speaker output terminal with L.P.F. Description Condition Unit Nominal Limit 1. Audio MAX Output (ATSC 0dBfs) Lch/Rch 10.0/10.0 9.0/9.0 2. Audio Distortion (NTSC) 500mW: Lch/Rch 0.5/0.5 2.0/2.0 PL15.16SP...
Page 10: Important Safety Precautions
IMPORTANT SAFETY PRECAUTIONS Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Page 11 3. Design Alteration Warning - Do not alter or add 7. Product Safety Notice - Some electrical and to the mechanical or electrical design of this TV mechanical parts have special safety-related receiver. Design alterations and additions, characteristics which are often not evident from including, but not limited to circuit modifications visual inspection, nor can the protection they give and the addition of items such as auxiliary audio...
Page 12 Precautions during Servicing A. Parts identified by the # symbol are critical for safety. Replace only with part number specified. B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.
Page 13 Safety Check after Servicing Examine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards. 1.
Page 14: Standard Notes For Servicing
STANDARD NOTES FOR SERVICING Circuit Board Indications How to Remove / Install Flat Pack-IC 1. The output pin of the 3 pin Regulator ICs is 1. Removal indicated as shown. With Hot-Air Flat Pack-IC Desoldering Machine: 1. Prepare the hot-air flat pack-IC desoldering Top View Bottom View machine, then apply hot air to the Flat Pack-IC...
Page 15 3. The flat pack-IC on the CBA is affixed with glue, so With Soldering Iron: be careful not to break or damage the foil of each 1. Using desoldering braid, remove the solder from pin or the solder lands under the IC when all pins of the flat pack-IC.
Page 16 With Iron Wire: 2. Installation 1. Using desoldering braid, remove the solder from 1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder the foil of each pin of the flat pack-IC on the CBA flux which is applied to all pins of the flat pack-IC, so you can install a replacement flat pack-IC more you can remove it easily.
Page 17 Instructions for Handling Semi- conductors Electrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work. 1. Ground for Human Body Be sure to wear a grounding band (1 M) that is properly grounded to remove any static electricity that may be charged on the body.
Page 18: Cabinet Disassembly Instructions [Type A]
CN1401 BLACK_NI + M4X12.0) 5(S-8), CN3105, Digital Main * : For reference CN3801, CN3901, CBA Unit Jack Holder *4 : 55PFL6900/F7 Stand D3 2(S-9) 1. Disassembly Flowchart Bracket Speaker D3 ---------------- This flowchart indicates the disassembly steps for the Speaker...
Page 19 • Be careful not to break the hook. If you pull with too much force, the hooks may be damaged. • Make sure to replace the Cell Cushion and Duble Side Tape to a new one when replacing the Front Cabinet. *4 : 55PFL6900/F7 PL15.16-A_DC...
Page 20 (L-2) (S-5) (L-2) (S-5) (L-2) [3] Rear Cabinet L (S-6) (L-1) (S-2) [2] Rear Cabinet R (S-4) (L-1) (S-1) Stand Neck (S-3) [1] Stand Base Assembly Fig. D1 (S-1) PL15.16-A_DC...
Page 21 [5] Digital Main CBA Unit Jack Holder (S-8) (S-8) [4] Power Supply CBA (S-7) Fig. D2 PL15.16-A_DC...
Page 22 [8] Speaker Holder (S-10) Hook [7] Speaker Sensor Shield [10] IR Sensor (S-10) CBA Unit * Function Knob (S-9) [7] Speaker [6] Stand Bracket [9] Function CBA Unit * Hook Knob Frame Fig. D3 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit.
Page 23 Decoration Plate LED Lens [12] LCD Panel Hook Assembly * Leading Edge Cover (S-11) T-CON Module (S-11) FFC Cable (S-11) [11] T-CON Holder * Fig. D4 : Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the LCD Panel Assembly.
Page 24 Hook (S-12) LED Lens (S-12) Leading Edge Cover (S-12) (S-12) Decoration Plate Leading Edge Cell Cushion UD Cover Duble Side Tape LED Lens Hook Cell Cushion LR (S-12) [13] Front Cabinet * (S-11) T-CON Module (S-11) [12] LCD Panel Assembly * FFC Cable (S-11) [11] T-CON Holder *...
Page 25 3. How to Replace the Front Cabinet 4. Slowly put the LCD Panel Assembly down. When replacing the Front Cabinet, the inner adjunctive equipment such as Cell Cushion must also be replaced all together. Disassembly Method CAUTION Disassembly MUST be performed in a CR (Clean Room).
Page 26 Work Prohibitions Lift middle part Cause colour spots (Diffusing (same for upper and sheet overlap) lower side) NG At worst, cell can be broken. Lift 1 corner only NG Cause colour spots (Diffusing sheet overlap) At worst, cell can be broken. Rotate to reverse Cause colour spots (Diffusing direction at left and...
Page 27 How to Attach Adjunctive Equipment There are no Cell Cushion, etc. attached on the new Front Cabinet to be replaced with. Apply adjunctive equipment such as Cell Cushion by consulting the following, then assemble the Front Cabinet. 1. Cell Cushion Two separate Cell Cushions must overlap in the center of the upper side.
Page 28 TV Cable Wiring Diagram To LCD Panel Assembly Power Supply CBA Digital Main CBA Unit CN1101 CN1201 CN1401 CN3601 CN652 CN3902 CN651 CN601 Function CBA Unit To AC Cord CN3901 CN3801 CN3105 To LCD Panel Assembly To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001 Fig.
Page 29: [Type B]
[TYPE B] This type prohibit the panel disassembly. Screw Torque Specification 1. Disassembly Flowchart This flowchart indicates the disassembly steps for the Ref. Part Tightening Part Name Number Torque cabinet parts and the CBA in order to gain access to SCREW BIND BLACK_NI items to be serviced.
Page 30 2. Disassembly Method Note: (1) Order of steps in procedure. When reassembling, Step/ Fig. follow the steps in reverse order. These numbers Loc. Part Removal Note are also used as the Identification (location) No. of parts in figures. Stand L, R D1 6(S-1) (2) Parts to be removed or installed.
Page 31 [2] Rear Cover L (S-2) (S-4) [3] Rear Cover R (S-3) (S-2) (S-3) (S-2) (S-1) (S-2) (S-4) [1] Stand L (S-1) [1] Stand R Fig. D1 4-14 PL15.16-B_DC...
Page 32 [4] Function CBA Unit Function Knob Tape Tape (S-5) Knob Frame Hook Hook CL3102 When assembling the rear cabinet, make sure to tapes the Fuction cable (CL3102) in place in order to prevent them from slipping off of the hook. Fig.
Page 33 [11] Stand Bracket L [10] Digital PCB Holder (S-11) (S-10) (S-11) (S-9) [11] Stand Bracket R (S-8) [9] Power PCB Holder [8] Speaker Holder L (S-8) [8] Speaker Holder R Fig. D4 4-16 PL15.16-B_DC...
Page 34 [15] LCD Panel Assembly [14] Front Bezel Front Bottom L (S-14) (S-14) Front Bottom R [13] Leading Edge Holder Front Bottom Center (S-14) (S-13) Decoration Plate Sensor Shield (S-13) Light Guide Panel [12] IR Sensor CBA Unit Leading Edge Front Leading Edge Rear (S-12) Fig.
Page 35 TV Cable Wiring Diagram Power Supply CBA Digital Main CBA Unit CN3601 CN651 CN3902 CN652 CN3901 CN3102 CN1201 CN601 CN3801 CN1101 CN3105 Function CBA Unit To LCD Panel To AC Cord Assembly IR Sensor To Speaker CBA Unit CN4051 CN4001 Fig.
Page 36: [Type C, E]
[TYPE C, E] Screw Torque Specification 2. Disassembly Method Step/ Ref. Part Tightening Fig. Part Name Number Torque Loc. Part Removal Note SCREW F-PAN BLACK_NI L10 GCHP3120 +P-TITE M3X12.0 Stand Base 8(S-1), 2(S-2), Stand SCREW BIND 3CHROM Assembly Hinge Assembly L23 GBJS3060 +S-TITE M3X6.0 Stand Base...
Page 37 Note: Important precautions concerning the LCD Panel Assembly: (1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers 1. When you disassemble/re-assemble the LCD are also used as the Identification (location) No. of Panel Assembly. parts in figures.
Page 38 (L-2) (S-6) (L-2) (S-6) (L-2) [3] Rear Cabinet L (S-7) (L-1) (S-3) [2] Rear Cabinet R (S-5) (L-1) (S-1) (S-4) (S-4) 55PFL4901/F7 55PFL4901/F8 Stand Neck Stand Hinge Assembly (S-1) (S-1) (S-2) Fig. D1 [1] Stand Base Assembly 4-21 PL15.16-C_DC...
Page 39 [5] Digital Main CBA Unit Jack Holder (S-9) [TYPE C] [4] Power Supply CBA (S-8) Fig. D2 4-22 PL15.16-C_DC...
Page 40 [8] Speaker Holder (S-10) Hook [7] Speaker Sensor Shield [10] IR Sensor (S-10) CBA Unit * Function Knob (S-9) [7] Speaker [6] Stand Bracket [9] Function CBA Unit * Hook Knob Frame Fig. D3 : Make sure to read all the precautions on page 4-20 when you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit.
Page 41 Decoration Plate LED Lens [12] LCD Panel Hook Assembly * Leading Edge Cover (S-11) T-CON Module (S-11) FFC Cable (S-11) [11] T-CON Holder * Fig. D4 : Make sure to read all the precautions on page 4-20 when you disassemble/re-assemble the LCD Panel Assembly.
Page 42 (S-13) (S-13) Decoration Plate Leading Edge Cell Cushion UD Cover Duble Side Tape LED Lens Hook Cell Cushion LR (S-13) [13] Front Cabinet * T-CON Module (S-12) [12] LCD Panel Assembly * FFC Cable (S-12) [11] T-CON Holder * Fig. D5 : Make sure to read all the precautions on page 4-20 when you disassemble/re-assemble the LCD Panel Assembly.
Page 43 3. How to Replace the Front Cabinet 4. Slowly put the LCD Panel Assembly down. When replacing the Front Cabinet, the inner adjunctive equipment such as Cell Cushion must also be replaced all together. Disassembly Method CAUTION Disassembly MUST be performed in a CR (Clean Room).
Page 44 Work Prohibitions Lift middle part Cause colour spots (Diffusing (same for upper and sheet overlap) lower side) NG At worst, cell can be broken. Lift 1 corner only NG Cause colour spots (Diffusing sheet overlap) At worst, cell can be broken. Rotate to reverse Cause colour spots (Diffusing direction at left and...
Page 45 How to Attach Adjunctive Equipment There are no Cell Cushion, etc. attached on the new Front Cabinet to be replaced with. Apply adjunctive equipment such as Cell Cushion by consulting the following, then assemble the Front Cabinet. 1. Cell Cushion Two separate Cell Cushions must overlap in the center of the upper side.
Page 46 TV Cable Wiring Diagram To LCD Panel To LCD Panel Assembly Assembly Power Supply CBA Digital Main CBA Unit CN1101 CN1201 CN1401 CN3901 CN501 CN3601 Function CBA Unit CN601 CN3801 CN3501 To AC Cord To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001 Fig.
Page 47: [Type D, F]
CBA Unit *5 *6 Cabinet Cell Cushion LR, Cell Cushion UD, [12] LCD Panel Doble Side Tape Assembly      [13] Front *5*6 Cabinet *4 : TYPE D *5 : TYPE F *6 : 55PFL6900/F7 A 4-30 PL15.16-D_DC...
Page 48 • Be careful not to break the hook. If you pull with too much force, the hooks may be damaged. • Make sure to replace the Cell Cushion and Duble Side Tape to a new one when replacing the Front Cabinet. *5 : TYPE F *6 : 55PFL6900/F7 A 4-31 PL15.16-D_DC...
Page 49 (L-2) (S-5) (L-2) (S-5) (L-2) [3] Rear Cabinet L (S-6) (L-1) (S-2) [2] Rear Cabinet R (S-4) (L-1) (S-1) (S-3) [TYPE D] [TYPE F] Stand Neck Stand Hinge Assembly (S-1) (S-1a) (S-1) [1] Stand Base Assembly Fig. D1 4-32 PL15.16-D_DC...
Page 50 [5] Digital Main CBA Unit Jack Holder (S-8) (S-8) [4] Power Supply CBA (S-7) Fig. D2 4-33 PL15.16-D_DC...
Page 51 [8] Speaker Holder (S-10) Hook [7] Speaker Sensor Shield [10] IR Sensor (S-10) CBA Unit * Function Knob (S-9) [7] Speaker [6] Stand Bracket [9] Function CBA Unit * Hook Knob Frame Fig. D3 : Make sure to read all the precautions on page 4-31 when you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit.
Page 52 55PFL6900/F8 A (Serial No.:TC1) Decoration Plate Hook LED Lens Leading Edge Cover Decoration Plate LED Lens [12] LCD Panel Hook Assembly * Leading Edge Cover (S-11) T-CON Module (S-11) FFC Cable (S-11) [11] T-CON Holder * Fig. D4 : Make sure to read all the precautions on page 4-31 when you disassemble/re-assemble the LCD Panel Assembly.
Page 53 55PFL5901/F8 Decoration Plate Hook (S-12) LED Lens (S-12) Leading Edge Cover (S-12) (S-12) Decoration Plate Leading Edge Cell Cushion UD Cover Duble Side Tape LED Lens Hook Cell Cushion LR (S-12) [13] Front Cabinet * (S-11) T-CON Module (S-11) [12] LCD Panel Assembly * FFC Cable (S-11) [11] T-CON Holder *...
Page 54 3. How to Replace the Front Cabinet 4. Slowly put the LCD Panel Assembly down. When replacing the Front Cabinet, the inner adjunctive equipment such as Cell Cushion must also be replaced all together. Disassembly Method CAUTION Disassembly MUST be performed in a CR (Clean Room).
Page 55 Work Prohibitions Lift middle part Cause colour spots (Diffusing (same for upper and sheet overlap) lower side) NG At worst, cell can be broken. Lift 1 corner only NG Cause colour spots (Diffusing sheet overlap) At worst, cell can be broken. Rotate to reverse Cause colour spots (Diffusing direction at left and...
Page 56 How to Attach Adjunctive Equipment There are no Cell Cushion, etc. attached on the new Front Cabinet to be replaced with. Apply adjunctive equipment such as Cell Cushion by consulting the following, then assemble the Front Cabinet. 1. Cell Cushion Two separate Cell Cushions must overlap in the center of the upper side.
Page 57 TV Cable Wiring Diagram To LCD Panel Assembly Power Supply CBA Digital Main CBA Unit CN1101 CN1201 CN1401 CN3601 CN652 CN3902 CN651 CN3901 CN601 Function CBA Unit To AC Cord CN3801 CN3105 To LCD Panel Assembly To Speaker CN4051 IR Sensor CBA Unit CN4052 CN4001 Fig.
Page 58: Electrical Adjustment Instructions [Type A, B, D, F]
ELECTRICAL ADJUSTMENT INSTRUCTIONS [TYPE A, B, D, F] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
Page 59 5. Press [3] button to select the “HDB” for High Drive The White Balance Adjustment should be Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel 6. Press [MENU] button. The internal Raster signal or Digital Main CBA. appears in the screen.
Page 60 13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature. Internal (Single) 14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR”...
Page 61: [Type C, E]
[TYPE C, E] 1. Purity Check Mode This mode cycles through full-screen displays of red, General Note: “CBA” is abbreviation for green, blue, and white to check for non-active pixels. “Circuit Board Assembly.” 1. Enter the service mode. Note: Electrical adjustments are required after 2.
Page 62 The White Balance Adjustment should be 5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.) performed when replacing the LCD Panel 6. Press [MENU] button. The internal Raster signal or Digital Main CBA. appears in the screen.
Page 63 14. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 13. Then check “Debugging Message”...
Page 64: How To Initialize The Lcd Tv
HOW TO INITIALIZE THE LCD TV The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized. To put the program back at the factory-default, initialize the LCD TV using the following procedure.
Page 65: Firmware Renewal Mode
FIRMWARE RENEWAL MODE Equipment Required 8. Select the file and press [OK] button. 9. The update will start and the following will appear a. USB storage device in the screen. b. Remote Control Unit " * " differs depending on the models. Firmware Update Procedure Software update 1.
Page 66 [TYPE D, F] Software update Please do NOT unplug your TV during this process. Doing so may corrupt the system making your TV inoperable. 100% Update in progress The update will take about 10 minutes. 13. After finished the updating software, TV set will automatically reboot.
Page 67: Troubleshooting
TROUBLESHOOTING Note: This Troubleshooting section covers the entire PL15.16 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model. [Power Supply Section] FLOW CHART NO.1 The power cannot be turned on.
Page 68 FLOW CHART NO.5 P-ON+21V is not output. Check C651, C652, D650, D651 and their periphery circuit. Repair it if defective. FLOW CHART NO.6 AMP+13V is not output. Check C654, C655, C657, C731, C732, D653, D654, D655, D658 and their periphery circuit. Repair it if defective.
Page 69 [Video Signal Section] FLOW CHART NO.1 The key operation is not functioning. Replace the Function CBA Unit. Replace the Digital Main CBA Unit. FLOW CHART NO.2 No operation is possible from the remote control unit. (Operation is possible from the unit.) Check AL+3.3V line and repair it if defective.
Page 70 [Audio Signal Section] FLOW CHART NO.1 [TYPE A, B, D, F] Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]> Replace the Digital Main CBA Unit. FLOW CHART NO.1 [TYPE C, E] Audio is not output normally. See FLOW CHART NO.6 <AMP+13V is not output.
Page 71: Block Diagrams [Type A]
BLOCK DIAGRAMS [TYPE A] 1. System Control Block Diagram PL15.16ABLS...
Page 72 2. Video/Audio Block Diagram PL15.16ABLVA...
Page 73 3. Digital Signal Process Block Diagram PL15.16ABLD...
Page 74 4. FRC Block Diagram PL15.16ABLFR...
Page 75 5. LED Backlight Drive Block Diagram PL15.16ABLBD...
Page 76 6. Power Supply Block Diagram PL15.16ABLP...
Page 77: [Type B]
[TYPE B] 1. System Control Block Diagram PL15.16BBLS...
Page 78 2. Video/Audio Block Diagram PL15.16BBLVA...
Page 79 3. Digital Signal Process Block Diagram PL15.16BLD...
Page 80 4. FRC Block Diagram PL15.16BLFR 9-10...
Page 81 5. LED Backlight Drive Block Diagram PL15.16BBLBD 9-11...
Page 82 6. Power Supply Block Diagram PL15.16BBLP 9-12...
Page 83: [Type C]
[TYPE C] 1. System Control Block Diagram PL15.16CBLS 9-13...
Page 84 2. Video/Audio Block Diagram PL15.16CBLVA 9-14...
Page 85 3. Digital Signal Process Block Diagram PL15.16CBLD 9-15...
Page 86 4. LED Backlight Drive Block Diagram PL15.16CBLBD 9-16...
Page 87 5. Power Supply Block Diagram PL15.16CBLP 9-17...
Page 88: [Type D]
[TYPE D] 1. System Control Block Diagram PL15.16DBLS 9-18...
Page 89 2. Video/Audio Block Diagram PL15.16DBLVA 9-19...
Page 90 3. Digital Signal Process Block Diagram PL15.16DBLD 9-20...
Page 91 4. LED Backlight Drive Block Diagram PL15.16ABLBD 9-21...
Page 92 5. Power Supply Block Diagram PL15.16ABLP 9-22...
Page 93: [Type E]
[TYPE E] 1. System Control Block Diagram PL15.16CBLS 9-23...
Page 94 2. Video/Audio Block Diagram PL15.16CBLVA 9-24...
Page 95 3. Digital Signal Process Block Diagram PL15.16CBLD 9-25...
Page 96 4. LED Backlight Drive Block Diagram PL15.16EBLBD 9-26...
Page 97 5. Power Supply Block Diagram PL15.16EBLP 9-27...
Page 98: [Type F]
[TYPE F] 1. System Control Block Diagram PL15.16FBLS 9-28...
Page 99 2. Video/Audio Block Diagram PL15.16DBLVA 9-29...
Page 100 3. Digital Signal Process Block Diagram PL15.16DBLD 9-30...
Page 101 4. LED Backlight Drive Block Diagram PL15.16ABLBD 9-31...
Page 102 5. Power Supply Block Diagram PL15.16FBLP 9-32...
Page 103: Schematic Diagrams / Cba And Test Points
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS Standard Notes WARNING Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc.
Page 104 LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES: 1. CAUTION: CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE. ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V. 2.
Page 105 Power Supply 1 Schematic Diagram [TYPE A, D] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 106 Power Supply 2 Schematic Diagram [TYPE A, D] L1301 L1101 C1303 C1302 C1301 C1103 C1102 C1101 100uH 100uH 220/35V 1/100V 1/100V 220/35V 1/100V 1/100V D1301 D1101 GP001 SB2150BD SB2150BD OPEN D1301A L1302 D1101A L1102 D1304 D1302 D1104 D1102 C1314 C1315 C1316 C1317 C1114...
Page 107 Power Supply 1 Schematic Diagram [TYPE B] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 108 Power Supply 2 Schematic Diagram [TYPE B] POWER SUPPLY CBA L1202 220uH L1201 C1201 C1202 C1206 C1203 220uH 330/63V OPEN OPEN OPEN L1102 CONTINUE 220uH POWER SUPPLY 1 L1101 C1101 C1102 C1106 C1103 220uH 330/63V OPEN OPEN OPEN D1201 D1101 SB2150BD SB2150BD D1203...
Page 109 Power Supply 1 Schematic Diagram [TYPE C] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 110 Power Supply 2 Schematic Diagram [TYPE C] GP001 L1301 L1101 OPEN C1303 C1302 C1301 C1103 C1102 C1101 100uH 100uH 220/35V 1/100V 1/100V 220/35V 1/100V 1/100V BC1302 D1301 BC1102 D1101 WIRE SB2150BD WIRE SB2150BD D1308 D1302 D1108 D1102 D1304 L1302 D1104 L1102 C1317 C1318...
Page 111 Power Supply Schematic Diagram [TYPE E] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 112 Power Supply 1 Schematic Diagram [TYPE F] CAUTION ! NOTE: Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. The voltage for parts in hot circuit is measured using CAUTION ! : For continued protection against risk of fire, If Main Fuse (F602) is blown , check to see that all components in the power supply hot GND as a common terminal.
Page 113 Power Supply 2 Schematic Diagram [TYPE F] L1301 L1101 C1303 C1302 C1301 C1103 C1102 C1101 100uH 100uH 220/35V 1/100V 1/100V 220/35V 1/100V 1/100V D1301 D1101 GP001 SB2150BD SB2150BD OPEN D1301A L1302 D1101A L1102 D1304 D1302 D1104 D1102 C1314 C1315 C1316 C1317 C1114 C1115...
Page 114 Digital Main 1 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 115 Digital Main 2 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 116 Digital Main 3 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 117 Digital Main 4 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. IC3001(4/9) MSD95C0H-3-002J DIGITAL SIGNAL PROCESS...
Page 118 Digital Main 5 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE TU3001 DIGITAL 9...
Page 119 Digital Main 6 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(6/9) MSD95C0H-3-002J...
Page 120 Digital Main 7 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 6...
Page 121 Digital Main 8 Schematic Diagram [TYPE A] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(8/9) MSD95C0H-3-002J...
Page 122 Digital Main 9 Schematic Diagram [TYPE A] CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V R3653 R3654 300K 150K R3651 R3652 CONTINUE R3628 DIGITAL 8 OPEN R3683 IC3602 IC3606 P-ON+3.3V Q3604 Q3605 OPEN MP2315GJ-Z R3630 2SK3018 2SK3018 (+1.05V REG.) AL+3.3V OPEN R3655 R3682 (SWITCHING) (SWITCHING) OPEN...
Page 123 Digital Main 10 Schematic Diagram [TYPE A] 1 NOTE: 2 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. The order of pins shown in this diagram is different from that of actual IC5001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section.
Page 124 Digital Main 11 Schematic Diagram [TYPE A] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 13 FRC+1.5V...
Page 125 Digital Main 12 Schematic Diagram [TYPE A] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 13 FRC+1.5V...
Page 126 Digital Main 13 Schematic Diagram [TYPE A] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 10 FRC+3.3V...
Page 127 Digital Main 1 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 128 Digital Main 2 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 129 Digital Main 3 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 130 Digital Main 4 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. IC3001(4/9) MSD95C0H-3-002J DIGITAL SIGNAL PROCESS...
Page 131 Digital Main 5 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE TU3001 DIGITAL 9...
Page 132 Digital Main 6 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(6/9) MSD95C0H-3-002J...
Page 133 Digital Main 7 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 6...
Page 134 Digital Main 8 Schematic Diagram [TYPE B] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(8/9) MSD95C0H-3-002J...
Page 135 Digital Main 9 Schematic Diagram [TYPE B] CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V R3653 R3654 300K 150K R3651 R3652 CONTINUE DIGITAL 8 R3683 IC3606 P-ON+3.3V Q3604 Q3605 MP2315GJ-Z 2SK3018 2SK3018 (+1.05V REG.) AL+3.3V R3655 R3682 (SWITCHING) (SWITCHING) OPEN AMP+13V C3648 R3649 R3650 P-ON+21V OPEN...
Page 136 Digital Main 10 Schematic Diagram [TYPE B] 1 NOTE: 2 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. The order of pins shown in this diagram is different from that of actual IC5001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section.
Page 137 Digital Main 11 Schematic Diagram [TYPE B] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 13 FRC+1.5V...
Page 138 Digital Main 12 Schematic Diagram [TYPE B] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 13 FRC+1.5V...
Page 139 Digital Main 13 Schematic Diagram [TYPE B] 2 NOTE: The order of pins shown in this diagram is different from that of actual IC5001. IC5001 is divided into four and shown as IC5001 (1/4) ~ IC5001 (4/4) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 10 FRC+3.3V...
Page 140 Digital Main 1 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 2 LCD+12V...
Page 141 Digital Main 2 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 5 AL+3.3V...
Page 142 Digital Main 3 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. IC3102(3/6) JK3701 MSD93F0JM4-3-002J...
Page 143 Digital Main 4 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 3 SPDIF...
Page 144 Digital Main 5 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3606 OPEN...
Page 145 Digital Main 6 Schematic Diagram [TYPE C, E] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3102. IC3102 is divided into six and shown as IC3102 (1/6) ~ IC3102 (6/6) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT C9011 C9012...
Page 146 Digital Main 1 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 147 Digital Main 2 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. CONTINUE DIGITAL 9 SOC+1.5V...
Page 148 Digital Main 3 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT C9011 C9012...
Page 149 Digital Main 4 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. IC3001(4/9) MSD95M2D-3-004E DIGITAL SIGNAL PROCESS...
Page 150 Digital Main 5 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 9...
Page 151 Digital Main 6 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. R3035 DIGITAL MAIN CBA UNIT OPEN...
Page 152 Digital Main 7 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 8...
Page 153 Digital Main 8 Schematic Diagram [TYPE D] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT IC3001(8/9) MSD95M2D-3-004E...
Page 154 Digital Main 8 Schematic Diagram [TYPE F] 55PFL5601/F7 model has the combination of more than one Wire Assembly and Digital Main PCB. 1 NOTE: See the following table for more information. The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section.
Page 155 Digital Main 9 Schematic Diagram [TYPE D, F] CONTINUE DIGITAL 4 P-ON+3.3V AL+3.3V R3653 R3654 240K R3651 R3652 CONTINUE R3628 DIGITAL 8 OPEN R3622 IC3602 IC3606 100K P-ON+3.3V Q3604 Q3605 OPEN MP2315SGJ-Z R3630 2SK3018 2SK3018 (+1.05V REG.) AL+3.3V OPEN R3655 R3621 (SWITCHING) (SWITCHING)
Page 156 Digital Main 10 Schematic Diagram [TYPE D, F] 1 NOTE: The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into nine and shown as IC3001 (1/9) ~ IC3001 (9/9) in this Digital Main Schematic Diagram Section. DIGITAL MAIN CBA UNIT CONTINUE DIGITAL 9...
Page 157 Function Schematic Diagram [TYPE A, C, D, E, F] FUNCTION CBA UNIT TO IR SENSOR CBA UNIT CN4051 CN4001 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4006 R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K 4.7K 8.2K SW4007 SW4006 SW4005 SW4004 SW4003 SW4002 SW4001...
Page 158 Function Schematic Diagram [TYPE B] FUNCTION CBA UNIT TO DIGITAL MAIN CBA UNIT CN3102 CN4001 KEY-IN1 C4002 D4001 MM5Z5V6B D4002 OPEN R4006 R4005 R4004 R4003 R4002 R4001 2.2K 2.2K 2.7K 4.7K 8.2K SW4007 SW4006 SW4005 SW4004 SW4003 SW4002 SW4001 POWER SOURCE MENU CH UP...
Page 159 IR Sensor Schematic Diagram [TYPE A, C, D, E, F] C4054 R4060 R4053 RS4051 OPEN RS-272 (REMOTE SENSOR) D4051 SMLE12WBC7W1HR POWER R4051 R4052 TO DIGITAL MAIN 6.8K CBA UNIT CN3105 R4054 CN4052 or CN3501 1 AL+3.3V 2 P-ON+5V 3 LIGHT C4051 C4056 C4052...
Page 160 IR Sensor Schematic Diagram [TYPE B] C4054 R4061 R4062 OPEN OPEN RS4051 RS-272 (REMOTE SENSOR) R4063 R4064 OPEN R4051 R4052 D4051 D4052 6.8K CL-840S-WT-SD-TS OPEN POWER TO DIGITAL MAIN R4054 CN4051 CBA UNIT CN3105 6 REMOTE 5 GND C4055 OPEN 4 LIGHT C4051 C4056...
Page 161 Power Supply CBA Top View [TYPE A, D] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 162 Power Supply CBA Bottom View [TYPE A, D] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 163 Power Supply CBA Top View [TYPE B] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 164 Power Supply CBA Bottom View [TYPE B] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 165 Power Supply CBA Top View [TYPE C] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 166 Power Supply CBA Bottom View [TYPE C] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 167 Power Supply CBA Top View [TYPE E] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 168 Power Supply CBA Bottom View [TYPE E] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 169 Power Supply CBA Top View [TYPE F] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 170 Power Supply CBA Bottom View [TYPE F] Because a hot chassis ground is present in the power supply CAUTION ! circuit, an isolation transformer must be used when repairing. Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. CAUTION ! : For continued protection against risk of fire, Also, in order to have the ability to increase the input slowly,...
Page 171 WIRING DIAGRAMS [TYPE A, D] SP3801 SP3802 SPEAKER SPEAKER L-CH R-CH CL3801 COMPONENT CN3105 CN4052 -Y/VIDEO-IN CN3801 IR SENSOR CBA UNIT CL3105 COMPONENT -Pb-IN CN4051 COMPONENT -Pr-IN CL4051 AUDIO(L)-IN REAR AUDIO(R)-IN CN4001 FUNCTION CBA UNIT DIGITAL AUDIO-OUT (OPTICAL) PC-RGB-IN AC CORD DIGITAL MAIN CBA UNIT ETHERNET CN3601...
Page 172: [Type B]
[TYPE B] SP3801 SP3802 SPEAKER SPEAKER L-CH R-CH CL3801 COMPONENT CN3105 CN4051 -Y/VIDEO-IN CN3801 CL3105 IR SENSOR CBA UNIT COMPONENT -Pb-IN COMPONENT -Pr-IN AUDIO(L)-IN CN3102 CN4001 AUDIO(R)-IN CL3102 FUNCTION CBA UNIT REAR DIGITAL AUDIO-OUT (OPTICAL) PC-RGB-IN AC CORD DIGITAL MAIN CBA UNIT ETHERNET CN3601 CN651...
Page 173: [Type C, E]
[TYPE C, E] SP3801 SP3802 SPEAKER SPEAKER L-CH R-CH CL3801 CN3501 CN4052 ANT-IN CN3801 CL3101 IR SENSOR CBA UNIT CN4051 USB JACK HEADPHONE SIDE JACK CL4001 [TYPE C, 55PFL4901/F8(Serial No.:DS1)] CL4051 HDMI- [55PFL4901/F8(Serial No.:TC2)] CONNECTOR-2 HDMI- CN4001 CONNECTOR-3 FUNCTION CBA UNIT HDMI- CONNECTOR-1 AC CORD...
Page 174: [Type F]
[TYPE F] 55PFL5601/F7 model has the combination of more than one Wire Assembly and Digital Main PCB. See the following table for more information. Type 1 Type 2 Type 3 Wire Assembly WX1A51REx313 WX1A51RJx303 WX1A51RJx303 Parts No. Digital Main PCB SP3801 SP3802 BA51REG04012...
Page 175: Exploded Views
EXPLODED VIEWS [TYPE A] MB14 LCD1 MB12 55PFL6900/F7 MB14 RA1-1 Digital Main CBA Unit CL3902 CL3601 CL3901 CL3105 IR Sensor CBA Unit SP3801 RA1-2 Power Supply CBA AC601 CL4051 CL3801 SP3802 Function CBA Unit SNA1 55PFL6900/F7 SSK1 55PFL6900/F8 See Electrical Parts List for parts with this mark.
Page 176 [TYPE B] LCD1 55PFL7900/F7 Digital Main CBA Unit B10-1 CL3601 A34-1 CL3902 A26-1 55PFL7900/F7 CL3901 B10-2 SP3801 A26-2 CL3105 A34-2 A3-1 A3-2 L111 CL3801 L111 MB27 SP3802 Function CBA Unit IR Sensor CBA Unit L111 55PFL7900/F7, 55PFL7900/F8 B19C 55PFL7900/F7 B18 B17 (Serial No.: TC1) B19B L111...
Page 177 [TYPE C, 55PFL4901/F8 (Serial No.: DS1)] MB14 LCD1 MB12 55PFL4901/F7 MB14 RA1-1 Digital Main CBA Unit CL3901 CL3601 B-1704 CL3101 IR Sensor CBA Unit TYPE C RA1-2 SP3801 Power Supply CBA CL3801 CL4001 SP3802 AC601 55PFL4901/F8 Function CBA Unit 55PFL4901/F8 55PFL4901/F7 SNA1 SNA1...
Page 178 [55PFL4901/F8 (Serial No.: TC2)] MB14 LCD1 MB12 MB14 RA1-1 Digital Main CBA Unit CL3901 CL3601 CL3101 IR Sensor CBA Unit RA1-2 SP3801 Power Supply CBA CL3801 CL4051 SP3802 AC601 Function CBA Unit SNA1 See Electrical Parts List for parts with this mark. SSK1 SBA1 SSK1...
Page 179 [TYPE D, F] 55PFL6900/F8 A, 55PFL5901/F8 MB14 LCD1 MB12 MB14 RA1-1 Digital Main CBA Unit 55PFL6900/F7 A, 55PFL5601/F7, 55PFL5901/F7 CL3902 CL3601 CL3901 CL3105 IR Sensor CBA Unit SP3801 RA1-2 Power Supply CBA AC601 CL4051 CL3801 SP3802 Function CBA Unit TYPE F...
Page 180 Packing [TYPE A, 55PFL6900/F7 A, 55PFL6900/F8 A (Serial No.:DS1)] 55PFL6900/F8 Packing Tape SNA1 55PFL6900/F8 Polybag Sheet 55PFL6900/F8 55PFL6900/F7, 55PFL6900/F7 55PFL6900/F8 A Fixlon Tape SSK1 Fixlon Tape PCB Label Tape Fixlon Tape SBA1 55PFL6900/F7, 55PFL6900/F7 A, 55PFL6900/F8 A Packing Tape Some Ref. Numbers are not in sequence.
Page 181 [TYPE B] 55PFL7900/F8 (Serial No.: XA1) Packing Tape 55PFL7900/F8 55PFL7900/F7, 55PFL7900/F8 (Serial No.: TC1) SSK1 PCB Label SA1-1 Tape Fixlon Tape SA1-2 Fixlon Tape Fixlon Tape 55PFL7900/F7 Fixlon Tape Packing Tape Some Ref. Numbers are not in sequence. 12-7 PL15.16-B_PEX...
Page 182 [TYPE C, E] 55PFL4901/F8 (Serial No.: TC2) Packing Tape 55PFL4901/F8 SNA1 55PFL4901/F8 (Serial No.: TC1) 55PFL4901/F7 SNA1 SSK1 Fixlon Tape TYPE E 55PFL4901/F7 SSK2 SSK1 55PFL4901/F8 (Serial No.: TC2) TYPEC, 55PFL4901/F7 (Serial No.: DS1) PCB Label Fixlon Tape 55PFL4901/F7, SBA1 55PFL4901/F8 (Serial No.: TC2) Tape...
Page 183 [55PFL6900/F8 A (Serial No.:TC1)] Packing Tape SNA1 SSK1 Fixlon Tape PCB Label Fixlon Tape Tape Fixlon Tape PCB Label SBA1 Packing Tape Some Ref. Numbers are not in sequence. 12-9 PL15.16-D_PEX...
Page 184 [55PFL5601/F7, 55PFL5901/F7] 55PFL5901/F7 (Serial No.: DS1) SSK1 SNA1 Fixlon Tape SSK2 PCB Label Fixlon Tape SBA1 Tape Fixlon Tape Packing Tape Packing Tape Packing Tape Some Ref. Numbers are not in sequence. 12-10 PL15.16-F_PEX...
Page 185 [55PFL5901/F8] Packing Tape SNA1 Fixlon Tape SSK2 SSK1 PCB Label Fixlon Tape SBA1 Tape PCB Label Fixlon Tape Packing Tape Some Ref. Numbers are not in sequence. 12-11 PL15.16-F_PEX...
Page 186: Parts List
TYPE A PARTS LIST [55PFL6900/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. ACCESSORIES Before replacing any of these components, read POLYETHYLENE BAG HDPE 180X340XT0.03...
Page 187 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a MSW ASSEMBLY # have special characteristics important to safety. Ref. No. Description Part No. Before replacing any of these components, read MSW ASSEMBLY A51RCMSW-001 carefully the product safety notice in this service Consists of the following manual.
Page 188 Ref. No. Description Part No. Ref. No. Description Part No. C1107 CHIP CERAMIC CAP .(1608) B K 0.047µF/25V CHD1EK30B473 C1613 CERAMIC CAP . 220pF/2kV CA3D221PAN04 C1108 CHIP CERAMIC CAP . B K 560pF/50V CHD1JK30B561 C1614 CERAMIC CAP . 220pF/2kV CA3D221PAN04 C1109 CHIP CERAMIC CAP .(1608) B K 1000pF/50V CHD1JK30B102...
Page 189 Ref. No. Description Part No. Ref. No. Description Part No. D1301 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150 Q1003 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U D1303 DIODE SWITCHING SMD 1SS400ST(SOD-523) ND1Z1SS400ST Q1004 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S D1304 ZENER DIODE MM5Z16B ND1B0MM5Z16B Q1101 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH D1305 ZENER DIODE MM5Z16B...
Page 190 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 10k Ω RES CHIP 1608 1/10W F 200k Ω R669 RRXA103HH013 R1125 RTW2003HH008 RES CHIP 1608 1/10W 0 Ω RES CHIP 1608 1/10W F 200k Ω R674 RRXA000HH014 R1126...
Page 191 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W J 10k Ω RES CHIP 1608 1/10W J 820k Ω R1406 RRXA103HH013 R1707 RRXA824HH013 RES CHIP 1608 1/10W J 100k Ω RES CHIP 1608 1/10W J 22k Ω R1407 RRXA104HH013 R1708...
Page 192 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 55PFL6900/F7 (Serial No. : DS1) Ref. No. Description Part No. Not used...
Page 193 C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 55PFL6900/F7 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A51RDMMA-004 TU3001 TUNER UNIT U9004UZ U9004UZ 2016/12/05 13-8...
Page 194 TYPE A PARTS LIST [55PFL6900/F8 (Serial No.: TC1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 195 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 196 2EMZ00441 SA1-1 STAND L A511ZUH 2EMZ00419 SA1-2 STAND R A511ZUH 2EMZ00420 Different parts from the original model SBA1 Not used 55PFL6900/F7 (Serial No. : DS1) SNA1 Not used SP3801 SPEAKER MAGNETIC SB05N70-A DS08060XQ004 Ref. No. Description Part No. SP3802 SPEAKER MAGNETIC SB05N70-A...
Page 197 Different parts from the original model C1111 CAP CHIP CERAMIC (1608) B K 2.2µF/16V CA1C225TE072 C1112 CHIP CERAMIC CAP .(3216) X7R K 1.0µF/100V CA2A105MR080 55PFL6900/F7 (Serial No. : DS1) C1113 CHIP CERAMIC CAP .(3216) X7R K 1.0µF/100V CA2A105MR080 Ref. No. Description Part No.
Page 198 Ref. No. Description Part No. Ref. No. Description Part No. C1401 Not used D1403 Not used C1402 Not used D1404 Not used C1403 Not used D1405 Not used C1405 Not used D1608 ZENER DIODE SMD TFZVTR18B QD1B00TFZV18 C1406 Not used D1711 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27...
Page 199 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W F 13.0k Ω RES CHIP 1608 1/10W J 5.1k Ω R627 RTW1302HH008 R1138 RRXA512HH013 RES CHIP 1608 1/10W J 1.0k Ω R628 Not used R1139 RRXA102HH013 RES CHIP 1608 1/10W J 100 Ω...
Page 200 Ref. No. Description Part No. R1318 Not used R1319 Not used R1320 Not used R1321 Not used R1323 Not used R1324 Not used R1325 Not used R1326 Not used R1327 Not used R1328 Not used R1329 Not used R1330 Not used R1331 Not used R1401...
Page 201 TYPE B PARTS LIST [55PFL7900/F8 (Serial No.: XA1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 202 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 203 TYPE B PARTS LIST [55PFL7900/F8 (Serial No.: TC1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 204 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 205 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 55PFL6900/F7 (Serial No. : DS1) Ref. No. Description Part No. A1-1...
Page 206 C643# CAP CERAMIC SAFETY 1000pF/250V E M CJMR102M42E1 Different parts from the original model C651 CAP ELE 330µF/25V/M/85 CED3310V8006 55PFL6900/F7 (Serial No. : DS1) C652 CAP ELE 330µF/25V/M/85 CED3310V8006 C660 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 Ref. No.
Page 207 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 1608 1/10W F 27.0k Ω C1707 Not used R660 RTW2702HH008 RES CHIP 1608 1/10W F 3.30k Ω C1710 CHIP CERAMIC CAP .(1608) B K 1000pF/50V CHD1JK30B102 R661 RTW3301HH008 RES CHIP 1608 1/10W 0 Ω...
Page 208 Ref. No. Description Part No. B-1704 POW HEAT SINK A7120UH 1EM423993A Not used B19A Not used B19C Not used BC1102 WIRE CP CP0.56 XZ40F0XRC001 BC1202 WIRE CP CP0.56 XZ40F0XRC001 BC1302 WIRE CP CP0.56 XZ40F0XRC001 BC1402 WIRE CP CP0.56 XZ40F0XRC001 BC1601 Not used BC1602 Not used...
Page 209 TYPE C PARTS LIST [55PFL4901/F8 (Serial No.: TC1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 210 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 211 TYPE D PARTS LIST [55PFL6900/F7 A (Serial No.: DS2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual.
Page 212 C..±0.25% D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model 55PFL6900/F7 (Serial No. : DS1) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A51RGMMA-001 IC3001 IC MSD95M0D-3-004E NSAA0RMST008 IC3101 Not used...
Page 213 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model TYPE D 55PFL6900/F7 A (Serial No. : DS2) Ref. No. Description Part No. A15#...
Page 214 D..±0.5% F..±1% G..±2% J..±5% K..±10% M..±20% N..±30% Z..+80/-20% Different parts from the original model TYPE D 55PFL6900/F7 A (Serial No. : DS2) Ref. No. Description Part No. DIGITAL MAIN CBA UNIT A51RHMMA-001 MSW ASSEMBLY A51RHMSW-001 Consists of the following FUNCTION CBA UNIT...
Page 215 TYPE D PARTS LIST [55PFL6900/F8 A (Serial No.: TC1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual.
Page 216 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 217 TYPE E PARTS LIST [55PFL4901/F8 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 218 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a Ref. No. Description Part No. # have special characteristics important to safety. C1106 CHIP CERAMIC CAP .(1608) B K 0.01µF/50V CHD1JK30B103 Before replacing any of these components, read C1107 CHIP CERAMIC CAP .(1608) B K 0.1µF/50V CHD1JK30B104 carefully the product safety notice in this service C1108...
Page 219 Ref. No. Description Part No. Ref. No. Description Part No. C1418 Not used IC1201 Not used C1616 Not used IC1301 Not used C1622 CERAMIC CAP . RB 330pF/2kV CA3D331TE006 IC1401 Not used C1623 CERAMIC CAP . RB 330pF/2kV CA3D331TE006 IC1702# Not used C1701 Not used...
Page 220 Ref. No. Description Part No. Ref. No. Description Part No. RES CHIP 3216 1/4W J 10 Ω R802 RRX4100HH034 R1226 Not used RES CHIP 3216 1/4W J 680 Ω R803 RRX4681HH034 R1227 Not used RES CHIP 1608 1/10W J 10k Ω R804 RRXA103HH013 R1228...
Page 221 Ref. No. Description Part No. RES CHIP 1608 1/10W F 6.80k Ω R1621 RTW6801HH008 RES CHIP 3216 1/4W J 10 Ω R1625 RRX4100HH034 RES CHIP 3216 1/4W J 10 Ω R1626 RRX4100HH034 R1632 Not used RES CHIP 1608 1/10W F 51.0k Ω R1645 RTW5102HH008 R1702...
Page 222 TYPE E PARTS LIST [55PFL4901/F8 (Serial No.: TC2)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 223 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 224 Don't degrade the safety of the product through improper servicing. NOTE: Parts that are not assigned part numbers (---------) are not available. Different parts from the original model 55PFL6900/F7 (Serial No. : DS1) Ref. No. Description Part No. A15#...
Page 225 M..±20% N..±30% Z..+80/-20% IC5003 Not used IC5006 Not used Different parts from the original model IC5602 Not used 55PFL6900/F7 (Serial No. : DS1) IC5604 Not used IC5605 Not used Ref. No. Description Part No. IC5606 Not used DIGITAL MAIN CBA UNIT...
Page 226 Ref. No. Description Part No. D1605 DIODE FAST RECOVERY /_1 SF38G B0 NDWZ000SF38G D1608 ZENER DIODE SMD TFZVTR18B QD1B00TFZV18 D1705A DIODE SCHOTTKY SMD RB520SM-30 T2R QD1ZRB520SM3 IC601 IC SWITCHING BM1P062FJ/SOP-J8 QSCA0T0RM432 Q602 Not used Q1103 MOS FET /_1 RSR020N06TL QF1ZSR020N06 Q1203 MOS FET /_1 RSR020N06TL QF1ZSR020N06...
Page 227 TYPE F PARTS LIST [55PFL5901/F7 (Serial No.: DS1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 228 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 229 TYPE F PARTS LIST [55PFL5901/F8 (Serial No.: FM1)] Mechanical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
Page 230 Electrical Parts PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing. NOTES: 1.
Page 231: Revision History
55PFL7900/F8 (Serial No.: TC1) First draft added • 2016/05/16 55PFL4901/F7 (Serial No.: DS6) First draft added • 2016/05/18 55PFL6900/F7 A (Serial No.: DS2) First draft added • 2016/05/19 55PFL4901/F8 (Serial No.: TC1) First draft added • 2016/05/23 55PFL4901/F8 (Serial No.: DS1) First draft added •...
Page 232 TYPE B 55PFL4901/F7 (DS6) A5DRGUH TYPE C 55PFL4901/F8 (TC1) A5DRDML TYPE C (DS1) A5DRJMH TYPE E (TC2) A5DRLML TYPE E 55PFL6900/F7 A (DS2) A51RGUH TYPE D 55PFL6900/F8 A (DS1) A51RHMH TYPE D (TC1) A51RKML TYPE D 55PFL5601/F7 (DS1) A51RJUH TYPE F...
Page 233 55PFL5601/F7 (Serial No.: DS1) A51RJUH SERVICE ADDITIONAL SHEET Notification on wiring ● Corresponding Models 55PFL5601/F7 (DS1) ● Symptom When replacing the Digital Main CBA Unit, replace it along with the Wire Assembly. When removing the Digital Main CBA Unit from the Main Unit, remove it along with the Wire Assembly and use them in pairs.

This manual is also suitable for:

55pfl6900/f8 55pfl7900/f7 55pfl7900/f8 55pfl4901/f7 55pfl4901/f8 55pfl5601/f7 ... Show all

Philips 55PFL6900/F7 Service Manual

Quick Links

Related Manuals for Philips 55PFL6900/F7

Summary of Contents for Philips 55PFL6900/F7

This manual is also suitable for:

Table of Contents