Table of Contents
Advertisement
C. Projecting images
Preparation:
• Remove the lens cap.
COMPUTER 1, 2 buttons
POWER button
DVI-D(HDCP) button
Main power switch
1. Put the projector into standby mode by pressing the main power switch. The POWER indicator lights up red.
• If the projector was turned off before the lamp was cooled down suffi ciently last time, the fan may start rotating
and the POWER button may not work after the main power switch is turned ON. (The STATUS indicator blinks
green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.
2. Turn on the power of the connected video equipment.
3. Press the POWER button.
• It may take about 1 minute for the lamp to light up.
• The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.
• Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the
lens cap.
• After the POWER button is pressed, the image may fl icker before the lamp becomes stable. This is not a prod-
uct malfunction.
• Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated
by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode
changes from STANDARD to LOW about 1 minute after turn-on.
• The projector starts warming up when the POWER button is pressed. During the warm-up process, images
may appear dark and no commands are accepted.
• By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when
the STATUS indicator blinks red. (See page 31.)
4. Press the ZOOM/FOCUS button on the projector or on the remote control to display "FOCUS".
5. Adjust with the
or
6. Select an input source.
• Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is
corresponding to the terminal in use.
• The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector.
• The VIDEO and S-VIDEO buttons don't function while the menu is being displayed.
• Though it may take some time before an image is displayed on the screen depending on the type of the input
signal, such symptom is not a malfunction.
• Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)
• When projecting images from a DVD player that is connected to the DVI connector, press the COMPUTER
button on the projector to select DVI or press the DVI-D(HDCP) button on the remote control.
• When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN-1
or COMPUTER/COMPONENT VIDEO IN-2 connector, press the COMPUTER button on the projector or the
COMPUTER 1 or COMPUTER 2 button on the remote control.
7. Adjust the position of the projector to keep an appropriate projection distance with which images are projected in
their specifi ed sizes.
8. Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)
• When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)
9. Press the ZOOM/FOCUS button on the projector or on the remote control to display "FOCUS" and then press the
button again to display "ZOOM."
10. Adjust with the
or
11. Press the LENS SHIFT button. "LENS SHIFT" will appear on the display.
12.Press the
or
button to adjust the vertical position and
displayed image.
Repeat steps 4, 5 and 9 to 12, if necessary.
Important:
• Focus, zoom and lens shift adjustment is possible in the normal picture mode only.
• When you press the ZOOM/FOCUS button or LENS SHIFT button while no signal is supplied, a blue background
screen is displayed.
S-VIDEO button
VIDEO button
button to get a fi ne picture.
button to get an approximate size.
POWER button
VIDEO button
COMPUTER button
ZOOM/FOCUS button
LENS SHIFT button
or
button to adjust the horizontal position of the
POWER
STATUS
AUTO POSITION
KEYSTONE
COMPUTER
ENTER
VIDEO
VOLUME
MENU
ZOOM/FOCUS
LENS SHIFT
EN-19
Advertisement
Table of Contents
