Sony LSPX-S1 - Glass Sound Speaker Startup Guide

Sony LSPX-S1 - Glass Sound Speaker Startup Guide

Also See for LSPX-S1:

Advertisement

Sony LSPX-S1 - Glass Sound Speaker Startup Guide

Parts and Controls

Do not directly touch areas , , and .
Parts and Controls

Buttons/Indicators/Terminals section

  1. DC IN 19.5 V jack
  2. AUDIO IN jack
  3. ON/STANDBY (power) button/indicator
    Press briefly to turn the illumination LED on and off. Press and hold to turn the speaker on and off.
  4. BLUETOOTH indicator

Speaker/Illumination LED section

  1. Passive radiator
  2. Glass tweeter
  3. Illumination LED
  4. Woofer
  5. Reflector

Base operating section

  1. (illumination LED) +/– buttons
    Raise and lower the brightness of the illumination LED.
  2. TIMER/ PAIRING button
    Press briefly to set the Sleep Timer.
    Press and hold to turn on pairing mode.
  3. ADD (Speaker Add function) button
  4. (volume) +/– buttons
  5. RESET button
  6. N-Mark
    Touch here when connecting by One-touch (NFC).

Charging

Be sure to charge the speaker before using it for the first time.

  1. Connect the AC adaptor to the DC IN 19.5 V jack.
    Charging begins, and the ON/STANDBY indicator (red) turns on.
    Charging

Hint
When battery power becomes low, the ON/STANDBY (red) indicator flashes, and after a short while, the speaker automatically turns off.

Turning the Power On/Off

  1. Press and hold the ON/STANDBY button for at least two seconds.

Hint
If you press the ON/STANDBY button briefly while the speaker is on, the illumination LED turns on/off.

How to Make a Wireless Connection with BLUETOOTH Devices

Select your case from the pairing types below.

  1. Pairing and connecting with a BLUETOOTH device
  2. Connecting with a BLUETOOTH device by One-touch (NFC)

Pairing and connecting with a BLUETOOTH device

If no BLUETOOTH devices are paired with the speaker when it is turned on, it will automatically enter pairing mode. Proceed to step 2.

  1. Press and hold the TIMER/ PAIRING button for at least two seconds.
    The speaker will make a sound to indicate that pairing mode has been entered, and the BLUETOOTH indicator (white) will flash.
    Pairing and connecting with a BLUETOOTH device
  2. Detect the speaker from the BLUETOOTH device and select [LSPX-S1].
  3. Confirm that the BLUETOOTH indicator (white) has lit up.
    The connection has been made.

Hint
If the indicator turns off in the middle of the operation, turn the power off and back on and then perform the operation again.

Connecting with a BLUETOOTH device by One-touch (NFC)

  1. Unlock the screen of your BLUETOOTH device and touch it to the N marked area on the bottom of the speaker.
    This operation can be performed even when the speaker is turned off.
    Connecting with a BLUETOOTH device by One-touch (NFC)
  2. Confirm that the BLUETOOTH indicator (white) has lit up.
    The connection has been made.

Disconnecting by One-touch
Touch the N marked area with the device again.

When you cannot establish a connection

  • Move the BLUETOOTH device slowly over the N marked area.
  • If the BLUETOOTH device is in a case, remove it from the case.

Listening to Music

Start playback on the BLUETOOTH device and adjust the volume.
Set the volume at an appropriate level on the connected device and adjust the volume with the buttons on the speaker.

Listening to Music from an External Device

  1. Connect a portable audio device to the AUDIO IN jack using an audio cable* (not supplied).
    * Stereo mini to stereo mini, no resistor
  2. Start playback on the connected device.

Hint
When listening to music from a BLUETOOTH device, remove the connection cord from the AUDIO IN jack.

Other Functions

  • Adjusting the Brightness of the Illumination LED
    Press the buttons
    Press and hold the button for rapid adjustments.
  • Using the Sleep Timer
    Press the TIMER/ PAIRING button.
    A sound will indicate that the Sleep Timer has been set, and the power will automatically turn off after 60 minutes.*
    * The duration setting can be changed by using SongPal.

Canceling the Sleep Timer
Press the TIMER/ PAIRING button again. A sound will indicate that the Sleep Timer has been canceled.

  • Listening to Music with Two Speakers (Speaker Add Function)
    Two LSPX-S1 speakers can play in stereo (stereo mode) or can play the same sound (double mode).
    When using the Speaker Add function, one speaker acts as the "master unit," while the other acts as the "satellite unit."
    Speaker Add Function - Step 1
  1. Turn on two speakers and bring them within 1 m (3 ft) of each other. Then press and hold the ADD button for at least two seconds on each.
    A sound will indicate that the Speaker Add function has been activated, and the BLUETOOTH indicator (orange) will flash.
    Speaker Add Function - Step 2
  2. Briefly press the ADD button on the speaker that you want to set as the master unit.
    The speaker that you operate will release a sound to indicate that it has been set as the "master unit" (left (L) channel).
    Another sound will indicate when the Speaker Add function is completely set up.
  3. Pair your BLUETOOTH device with the master unit.
    For details, see "How to Make a Wireless Connection with BLUETOOTH Devices."
    If pairing has already been performed, then just connect.
  4. Start playback on the BLUETOOTH device.

Hint

  • Once setup is complete, the speakers can be separated by more than 1 m (3 ft).
  • While using the Speaker Add function, the volume and brightness of both speakers are synchronized. Adjustments can be made from either speaker.

Switching between stereo mode and double mode
Each time you press the ADD button on the master unit while using the Speaker Add function, the mode switches in this order: stereo mode (left channel) → stereo mode (right channel) → double mode. When switching the channel in stereo mode, the satellite unit automatically switches to the opposite channel.
In stereo mode, the BLUETOOTH indicator for the left (L) channel is orange, and for the right (R) channel is red. In double mode, both BLUETOOTH indicators are orange.

Canceling the Speaker Add function
Press and hold the ADD button for at least two seconds. A sound will indicate when the setting has been canceled.

Note
You cannot listen to music from an external device connected to the AUDIO IN jack while using two speakers.

Resetting

When the speaker is not working properly, resetting it may resolve some issues.
Use a pointed object, such as a pin, to press the RESET button.

Note
Pairing information is not erased by resetting the speaker.

FAQ

Refer to the Help Guide for more detailed solutions.

There is noise when connected via BLUETOOTH.
This may be caused by signal interference. Try moving the speaker to a different location. If the noise disappears depending on the location, the speaker has not malfunctioned. Using SongPal to switch the BLUETOOTH codec to [Prioritize connection] (SBC) may also resolve the issue.

The speaker automatically turns off, and the ON/ STANDBY indicator flashes in red.
The speaker has entered protect mode. Unplug the power cord, and then remove all connected cords from the jacks on the speaker. Reconnect the power cord and turn on the speaker. If the issue is not resolved, contact your nearest Sony dealer.

BLUETOOTH is connected, but there is no sound.

  • Make sure that the speaker is turned on. When the speaker is on, the ON/STANDBY indicator is lit up in white or orange.
  • Make sure that the speaker has a BLUETOOTH connection with the BLUETOOTH device.
  • Pair the speaker with the BLUETOOTH device again.
  • The volume of the speaker or BLUETOOTH device may be low. Adjust the volume to a moderate level.
  • If a cord is connected to the AUDIO IN jack of the speaker or to the BLUETOOTH device, unplug it.

SongPal

SongPal allows you to operate any supported Sony audio devices from your smartphone/iPhone.

How to Download
Search for SongPal in Google Play™ (Play Store) or the App Store, and download.

www.apple.com
play.google.com

Features

  • Adjust the illumination LED
  • Set the sound quality
  • Set the BLUETOOTH codec
  • Set the Sleep Timer

For details, refer to the help page for SongPal
http://info.songpal.sony.net/help/

Note

  • While using SongPal, the sound source cannot be switched between a BLUETOOTH device and a device connected to the AUDIO IN jack.
  • The operations that SongPal can perform vary depending on the audio device. Specifications for the app are subject to change without prior notice.

Help Guide Information

Refer to the Help Guide for more easy-to-understand troubleshooting tips. Use a computer or smartphone/iPhone to access it.
http://rd1.sony.net/help/speaker/lspx-s1/h_zz/

©2016 Sony Corporation
Printed in Japan

Documents / Resources

References

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download Sony LSPX-S1 - Glass Sound Speaker Startup Guide

Advertisement

Table of Contents