Related Manuals for Charnwood W796
Summary of Contents for Charnwood W796
- Page 1 DUST & CHIP EXTRACTOR OWNERS MANUAL MODEL: W796 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. - Page 3 7. DO NOT use without the filter bag and collection bag in place. 8. Keep hair, loose clothing, fingers, and all parts of the body away from the end of the suction hose. W796 Specification Motor (induction) 750w (1hp), 240v, 50hz, 2850rpm...
- Page 4 A B C Filter Bag Support Hose Clamp Handle Collector Support Fixings Pack Filter Bag Bag Strap Hose Collection Bag Foam Strip Collector Body Support Leg Castors Base Assembly Install the 4 Castors to the Base Secure each castor with a washer and domed nut.
- Page 5 Attach the 2 Support Legs to the Base Use 2 of the Hex head Screws To secure each leg. Tighten with a 12mm spanner Attach the Collector Support to the Base Use 2 of the Hex head Screws To secure the support. Tighten with a 12mm spanner Lift the Motor and Collector Body unit above the support legs and then lower...
- Page 6 Secure the Collector Body to the Support Legs Use 4 Hex Head Screws. Tighten with a 12mm spanner Fit the Filter Bag Support Push the Filter Bag Support into the 2 holes located in the rim of the collector drum. Firmly press down until it is fully seated on both sides.
- Page 7 Fit the plastic Collection Bag Open the bag and fit it over the outside of the Collector Body rim. Tip: If you find this step tricky, use a couple of pieces of tape to secure the plastic bag in place whilst fitting the strap.
-
Page 8: Optional Items
Fit the Hose Place a Hose Clamp over the outside of one end the Hose. Push it onto the inlet, on the underside of the Collector Body. Use a cross head screw driver to close the Hose Clamp until it is tight. The second Hose Clamp can be used on the other end of the hose to secure it to a hose fitting or the dust hood of a... -
Page 9: Troubleshooting
Troubleshooting Reduced Performance Check the collection bag is not full. Empty or replace the bag as required. Check the filter bag is not clogged. Turn the bag inside out and scrape the inside clean. The filter bag can also be washed, ensure it is completely dry before refitting. -
Page 10: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Dust Extractor, Model W796 & W796CF Conforms with the following Directives: Machinery Directive 2006/42/EC Low Voltage Directive 2006/95/EC Conforms with the following UK Regulations: Supply of Machinery (Safety) Regulations 2008 Electrical Equipment (Safety) Regulations 2016 And further conforms to the machinery example for which the EC type examination Certificate No. - Page 11 Charnwood W796 Parts List Part No. Description Quantity Base Caster 5/16” Domed Nut 5/16” Collector Body Hex. Head Screw M6 x 20mm Impellor Washer Impellor 228mm Diameter Hex. Head Screw 5/16” x 5/16” Hex. Head Screw 1/4” x 1/2” Washer 1/4” x 25 Inlet Cover Hex.
- Page 12 CHARNWOOD W796 EXPLODED VIEW DIAGRAM Update October 2022...