Table of Contents
Advertisement
Quick Links
DUST & CHIP EXTRACTOR
OWNERS MANUAL
MODELS: W791, W791/3, W791CF, W791/3CF
A 16 amp fixed electric
supply is required to run
this machine.
Recommended breaker size:
16 Amps (Type C)
Charnwood, Cedar Court, Walker Road,
Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU
Tel. 01530 516 926
email: sales@charnwood.net
website: www.charnwood.net
1
Advertisement
Table of Contents
Related Manuals for Charnwood W791
Summary of Contents for Charnwood W791
- Page 1 DUST & CHIP EXTRACTOR OWNERS MANUAL MODELS: W791, W791/3, W791CF, W791/3CF A 16 amp fixed electric supply is required to run this machine. Recommended breaker size: 16 Amps (Type C) Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel.
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. - Page 3 7. DO NOT use without the filter bag and collection bag in place. 8. Keep hair, loose clothing, fingers, and all parts of the body away from the end of the suction hose. W791 Specification Motor (Available in 240v single phase or 415v 3 phase)
- Page 4 Unpacking This machine is supplied in 2 cartons. Open the cartons and carefully unpack all of the contents. Y-Piece Inlet Filter Bag Support Foam Sealing Strip Motor Assembly Base Plate Handle Collector Body Right Side Panel Collection Bag Filter Bag Castors Bag Straps Left Side Panel...
- Page 5 Assembly Install the 4 Castors to the Base Turn the base upside down Secure each castor using 4 Hex. Head screws Tighten with a 12mm spanner, or socket set Attach the 2 Side Panels to the Base Turn the base back over so it now sits on the castors.
- Page 6 Use 8 of the Hex Head screws to secure the motor assembly Attach the Collector Body to the Motor Assembly Place the Rubber Gasket between the 2 parts. Tip: Use a G clamp to hold the 2 parts in place whilst fitting the screws. Use 8 of the Hex Head screws to secure the Collector Body...
- Page 7 Fit the Handle Attach the Handle using the 2 smaller Hex head screws. Tighten with a 12mm spanner Fit the Filter Bag Support Thread a Nut 20mm onto the end of the Filter Bag Support Add a Washer Screw the Filter Bag Support into the threaded hole in the Collector Body Rotate at least 5 times and stop with the hook directly over the centre of the...
- Page 8 Fit the plastic Collection Bag Open the bag and fit it over the outside of the Collector Body rim. Use the 3 spring clips, located around the drum, top hold the bag in place whilst fitting the Bag Strap. Fit the Bag Strap over the plastic bag, so it sits on the foam strip.
-
Page 9: Installation
Fit the Y-Piece The standard inlet on the extractor is 125mm diameter. It can be converted to 2 x 100mm diameter inlets by fitting the Y-Piece. Use a cross head screwdriver to remove the retaining screw from the inlet. Fit the Y-piece over the inlet and then re-fit the screw. -
Page 10: Optional Items
When using the extractor with machines or power tools which have a smaller diameter connection, it is recommended to run the 100mm diameter hose from the extractor up to the machines dust outlet and fit the appropriate sized reducer at that point. This will maintain the airflow rate of the unit. -
Page 11: Troubleshooting
Troubleshooting Reduced Performance Check the collection bag is not full. Empty or replace the bag as required. Check the filter bag is not clogged. Turn the bag inside out and scrape the inside clean. The filter bag can also be washed, ensure it is completely dry before refitting. -
Page 12: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Dust Extractor, Models: W791, W791CF, W791/3 & W791/3CF Conforms with the following Directives: Machinery Directive 2006/42/EC Low Voltage Directive 2006/95/EC Conforms with the following UK Regulations: Supply of Machinery (Safety) Regulations 2008 Electrical Equipment (Safety) Regulations 2016 And further conforms to the machinery example for which the EC type examination Certificate No. - Page 13 Charnwood W791 Parts List Part No. Description Quantity Castor Hex. Screw 5/16” x 1/2“ Base Plate Left Side Panel Right Side Panel Pan Screw 3/16” x 3/8” Impellor Housing Cover Hex Screw M6 x 20 (Left Hand Thread) Washer Set Screw 5/16” x 1/2"...
- Page 14 CHARNWOOD W791 EXPLODED VIEW DIAGRAM...
- Page 15 Update October 2022 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 email: sales@charnwood.net website: www.charnwood.net...