Table of Contents
Advertisement
Quick Links
DUST & CHIP EXTRACTOR
OPERATORS MANUAL
MODEL: W691
Please Note:
This machine requires
a 16amp electric supply
Charnwood, Cedar Court, Walker Road,
Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU
Tel. 01530 516 926 Fax. 01530 516 929
email: sales@charnwood.net
website: www.charnwood.net
1
Advertisement
Table of Contents
Related Manuals for Charnwood W691
Summary of Contents for Charnwood W691
- Page 1 DUST & CHIP EXTRACTOR OPERATORS MANUAL MODEL: W691 Please Note: This machine requires a 16amp electric supply Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. - Page 3 11. Wear proper apparel. Avoid loose clothing, gloves, ties, rings, bracelets, and jewellery which could get caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long hair. 12. Always use safety glasses. Normal spectacles only have impact resistant lenses.
-
Page 4: Specification
Specification Motor (induction) 1500w (2hp), 240v Flowrate (cubic metres per hour) 2000m /hour Inlet Diameter 1 x 125mm or 2 x 100mm Bag capacity 148 Litres Collection Bag Size (order ref W791PB) 800mm x 1075mm Maximum continuous run time 2 hours Dimensions (WxDxH) 900mm x 560mm x 1950mm Weight... - Page 5 Assembly Leave all bolts finger tight until each castor is fitted. Place the base upside down and bolt one of the castors into the corner as shown. Use 4 domed cross head bolts, nuts and washers provided, to mount each castor. Continue with the remaining three.
- Page 6 Bolt on the three collector support arms, making sure that the tops are cranked inwards. Use 2 M8 x 16mm hex head bolts, washers and nuts to secure each support arm. Place the assembled unit on the floor. Lift the collector, part 33, and hold it in position with the 3 support arms on the outside of the collector.
- Page 7 Fit the transparent plastic bag over the bottom of the collector and secure it with one of the flexible clamps. If you have a helper, have them hold the bag in place for you while you attach and tighten the clamp.
-
Page 8: Optional Items
Gates can be used to close off any branch lines which are not currently in use. Reducing Connectors: Charnwood have a large range of plastic connectors, which allow different diameter hoses to be connected together or for connecting to bench... -
Page 9: Troubleshooting
Troubleshooting Reduced Performance Check the collection bag is not full. Empty or replace the bag as required. Check the filter bag is not clogged. Turn the bag inside out and scrape the inside clean. The filter bag can also be washed, ensure it is completely dry before refitting. -
Page 10: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Dust Collector, Model W691 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2004/108/EC And further conforms to the machinery example for which the EC type examination Certificate No. AM 50189644 and AE 50220714 have been issued by TUV Rheinland LGA Products GmbH, Tillystrasse 2, 90431, Nurnberg. - Page 11 CHARNWOOD W691 EXTRACTOR EXPLODED DIAGRAM...
- Page 12 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...