Related Manuals for Charnwood W685
Summary of Contents for Charnwood W685
- Page 1 WALL MOUNTED DUST EXTRACTOR MODEL: W685 & W685KIT Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. - Page 3 13. Always use safety glasses. Normal spectacles only have impact resistant lenses. They are not safety glasses. 14. Do not over-reach. Keep proper footing and balance at all times. 15. Maintain the machine in good condition. Keep the machine clean for best and safest performance.
-
Page 4: Specification
Specification Motor (Induction) 750W (1hp) 240V Flow Rate 850 cubic metres per hour Inlet Diameter 100mm Bag Capacity 60 litres Filtration Level 5 microns Maximum Recommended Hose Length 3 metres Maxumu Continuous Run Time 2 hours Weight 27kg Rating Hobby Warranty 1 Year Hobby Rating –... - Page 5 Unpack the parts carefully and check that everything is present as shown. If anything is missing contact your retailer immediately. Assembly Leave all bolts finger tight until each castor is fitted. Place the machine on its back and bolt one of the castors to the baseplate using four dome head M5 bolts with washers and nuts on the underside.
- Page 6 Stand the extractor on its castors. Insert two M6 bolts into the top holes of the square extractor outlet and slip the rubber gasket onto them. Fit the plastic adapter over the bolts and secure with washers and nuts. Add the remaining four bolts. Tighten the nuts when all six bolts are in position.
- Page 7 Fix the handle to the fan casing using the two M6 bolts supplied. Fit the dust collection bag over the round outlet and secure it in place with the jubilee clip supplied. The dust bag is emptied through the inlet after first removing it from the extractor.
- Page 8 W685KIT Hose & Dust Hood Kit (Optional Accessory) The Kit consists of a 3m length of 100mm diameter flexible hose, a dust hood and a support arm that can be positioned in a convenient place to collect from bench top machinery, most notably a woodturning lathe.
- Page 9 Insert the reduced end of the support arm into the mounting bracket. Attach the adjustable bracket assembly to the dust hood using the bolts, nuts and washers fitted to the hood. Ensure that the heads of the bolts are inside the hood and the nuts/washers outside.
-
Page 10: Troubleshooting
Using the Extractor The W685 extractor is designed to collect wood dust, chips and shavings from the woodworking machine, transport it into the collection bag and filter the clean air out. Because this is a single bag machine, the same bag acts as collector and filter. The bag should therefore be emptied when 50% full, otherwise there will not be enough surface area to act as a filtration medium and performance will be impaired. -
Page 11: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Dust Collector, Model W696 Conforms with the following Directives: Machinery Directive 2006/42/EC EMC Directive 2004/108/EC And further conforms to the machinery example for which the EC type examination Certificate No. AM 50187475 and AE 50220617 have been issued by TUV Rheinland LGA Products GmbH, Tillystrasse 2, 90431, Nurnberg, Germany. - Page 12 Charnwood W685 Parts List Part No. Description Part No. Description Castor Pan Head Screw 02-1 Hex Nut Washer Base Pan Head Screw Inlet Cover Left Hand Cap Screw Set Screw Washer Impeller Impeller Housing Washer 12-1 Hex Nut Hex Bolt...
- Page 13 Charnwood W685KIT Parts Drawing W685KIT Parts List Part No. Description Part No. Description Dust Hood Support Bracket Washer Dust Hood Bracket Bracket Adapter Locking Lever Hose 100mm x 3m Hose Clip 100mm Coach Bolt M8 x 20mm Washer M8 Nut M8...
- Page 14 Updated October 2016 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 Fax. 01530 516 929 email: sales@charnwood.net website: www.charnwood.net...