Oceanic OCEATV3Z60B User Manual page 42

Pressing again will switch off the Triple
Zone of the heater. Each operation causes
a status change of the Dual and Triple
zones in the following manner: dual zone
on/off, triple zone on, all extended zones
off, dual zone on/off, triple zone on, all
zones off, and so on.
Set Cooking Level with and without Heat
Boost
All heaters are equipped with the heat
boost function.
If the heat boost is required, set the heat
from the current level to level 9 by pressing
the button only. Once level 9 has been
reached, press
boost. The display will flash "A" alternating
with the heat setting value "9" to show the
heat boost is active.
If the heat boost is active, the heater will
operate with maximum power for a period of
time dependent on the heat setting selected
before the heat boost was activated.
Once the heat boost time has ended, only
the heat setting will be indicated on the
heater display.
The heat boost can be deactivated by
pressing until the heat setting "0" is
displayed.
Switching Off Individual Heaters
A heater can be turned off in 3 different
ways:
• Simultaneous pressing of
buttons
• Reduction of the heat setting to ´0` by
pressing the
• Use of the timer switch-off function for
the corresponding heater.
Simultaneous operation of
buttons
The corresponding heater must be chosen
with the Activate/Deactivate Heater Button
, the Decimal Point of the related
Heater Display will then flash. To switch
off the heater, and
simultaneously. A buzzer will sound and "0"
will appear in the heat setting display when
this is successful.
If the timer is active for the selected heater,
then "0" will appear in the heater and timer
displays, and the related Cooking Zone
Indicator and the Timer Function will both
switch off.
If there is any residual heat for the heater,
this will be indicated by a "H" in the heat
to activate the heat
and
button
and
must be pressed
setting display.
Reduction of the heat setting to "0" by
operating
The heater can also be switched off by
reducing the heat setting to "0".This causes
the associated Decimal Point of the heater,
the related Cooking Zone Indicator and the
Timer Display to all switch off, also.
If there is any residual heat for the heater,
this will be indicated by a "H" in the heat
setting display.
Use of timer switch-off function for
corresponding heater
After counting down to zero, the timer will
stop. The corresponding heater will show
"0" in the Heater Display and the Timer
Display will show "00". The corresponding
Cooking Zone Indicator will disappear.
An assigned Dual/Triple Zone Selection
Indicator will also disappear if it is active.
Additionally, the buzzer will sound when the
timer stops. Pressing any button will silence
the timer.
Timer Function
The timer provides the following features.
The control can run a maximum of 2 heater
assigned timers and 1 minute minder
timer (which is not assigned to a heater)
simultaneously.
The timers can only be used in B-Mode.
A heater timer can only be assigned to an
active heater set at a level between 1 and
9. The minute minder timer is independent
of any heater.
In order to use both functions, the timer
function must be activated using the
Activate/Deactivate Timer button
Pressing for the fist time, after activating
the heaters, controls the minute minder
timer (no Cooking Zone Indicator will flash,
they will all be either on or off).
Pressing for a second time, will assign
a timer to one of the activated heaters. The
Cooking Zone Indicator will begin flashing.
Pressing again, will assign the next timer
in a clockwise direction to the next active
heater, and so on.
Minute Minder Timer
The Minute Minder Timer can be operated
by pressing
activated or not, and is selected only when
all Cooking Zone Indicators are either on or
off, i.e. none are flashing.
The Timer Display will show "00", indicating
EN - 17
button
, whether a heater has been
.