Table of Contents
Advertisement
Quick Links
Thoroughly read and understand this manual before
installing, operating or servicing this equipment.
PREMIUM SERIES
OPERATION, INSTALLATION,
MAINTENANCE AND REPAIR GUIDE
SERVICE BULLETIN SB2001
HOSE REELS
TM
Multi-Purpose Dispense
Models: 2110-XXX
See page 3 for Hose Reel Model
Numbers and Technical Data
REV. K 7/11
®
Advertisement
Table of Contents
Related Manuals for Balcrank PREMIUM 2110 Series
Summary of Contents for Balcrank PREMIUM 2110 Series
- Page 1 SERVICE BULLETIN SB2001 REV. K 7/11 ® PREMIUM SERIES HOSE REELS Multi-Purpose Dispense Models: 2110-XXX See page 3 for Hose Reel Model Numbers and Technical Data Thoroughly read and understand this manual before installing, operating or servicing this equipment. OPERATION, INSTALLATION, MAINTENANCE AND REPAIR GUIDE...
-
Page 2: General Safety
General Safety CAUTION Thoroughly read and understand this manual before installing, operating or Be aware of possible fluid thermal expansion! A servicing this equipment. pressure relief valve should be properly installed in any system where this product is used. Should this IMPORTANT product fail as a result of thermal expansion and no pressure relief valve was installed, the product... -
Page 3: Model Numbers
Model Numbers NOTE (1): Inlet hoses are included with Premium Series Open Type of Model Hose Maximum Outlet Inlet Bare Service Size Working Hose Hose Reel Pressure 2110-013 30’ x 3/8” 250 psi 8136-030 8141-002 2110-024 Low Pressure 2110-014 40’ x 3/8” 250 psi 8136-040 8141-002... -
Page 4: Installation
Installation 2. Locate the mounting holes for drilling, using measurements on previous page. If mounting Tank/Wall Mounting: directly to I-Beam use mounting kit 2230-013 (no The hose reel has been shipped for a ceiling mount drilling required). application unless specified differently. The outlet 3. - Page 5 Installation WARNING: Wear Heavy Leather Increasing Power Spring Tension: Gloves when replacing service hose and/or 1. Pull the hose out fully and engage the stop replacing power spring to protect your hands from pawl. injury. 2. Be sure the system pressure has been relieved. Follow the pressure relieve procedures below.
-
Page 6: Maintenance
Tank/Mobile Mounting Position: NOTE: Check the power spring tension. The 1. Pull the hose out fully and engage the stop pawl. hose must pull out and retract fully. Wrap ONE Place C-Clamp on spool to prevent possible more loop onto or off the spool, extend the bodily injury. - Page 7 Maintenance Replacing Power Spring: CAUTION 1. Be sure the pressure supply has been relieved when. Follow the pressure relieve USE EXTREME CARE WHEN procedures below. HANDLING THE POWER SPRING! The spring is ALWAYS under great tension and could be propelled from the case with enough WARNING force to cause serious bodily injury.
- Page 8 Replacing Power Spring continued 12. Twist the complete spring case assembly to the left or right, making sure that the power spring is centered and has engaged the spring center plates (26). 13. Align upright assembly (15) with base (40) and tip tie bar (19).
-
Page 9: Troubleshooting Guide
Doing so may cause spring (37) and snap ring (39). Once this damage to reel and/or personal injury. has been done the complete assembly can Always use genuine Balcrank replacement be removed. parts. 3. Item (36) bronze bearing will need to be NOTE: Number with “*”... - Page 12 For Warranty Information Visit: www.balcrank.com Revision Log: Balcrank Corporation Weaverville, NC 28787 Rev. G - Changed swivel to 831488. 800-747-5300 Rev. H - Added Troubleshooting Table. 800-763-0840 Fax Rev. I - Added item 55 and revised item 10. www.balcrank.com Added Model #2110-026.